[PATCH 02/10] mmc: sdhci-of-k1: enable essential clock infrastructure for SD operation

[Yixun Lan]

Hi Iker,

On 16:13 Mon 02 Mar     , Iker Pedrosa wrote:
> Ensure SD card pins receive clock signals by enabling pad clock
> generation and overriding automatic clock gating. Required for all SD
> operation modes.
> 
> Signed-off-by: Iker Pedrosa <ikerpedrosam at gmail.com>
> ---
>  drivers/mmc/host/sdhci-of-k1.c | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/mmc/host/sdhci-of-k1.c b/drivers/mmc/host/sdhci-of-k1.c
> index 0cc97e23a2f9c7b2f9376318a8a7ebb860571504..b703b78282ed8d89183c816477c149c0a565618a 100644
> --- a/drivers/mmc/host/sdhci-of-k1.c
> +++ b/drivers/mmc/host/sdhci-of-k1.c
> @@ -20,6 +20,13 @@
>  #include "sdhci.h"
>  #include "sdhci-pltfm.h"
>  
[snip]

> +	spacemit_sdhci_setbits(host, SDHC_OVRRD_CLK_OEN | SDHC_FORCE_CLK_ON,
> +			       SPACEMIT_SDHC_OP_EXT_REG);
As I'm testing on Bananapi F3 board with emmc chip, this line will cause timeout problem

[   27.613806] mmc2: Timeout waiting for hardware interrupt.
[   27.616592] mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
[   27.623007] mmc2: sdhci: Sys addr:  0x00000400 | Version:  0x00000002
[   27.629429] mmc2: sdhci: Blk size:  0x00007200 | Blk cnt:  0x000003a6
[   27.635853] mmc2: sdhci: Argument:  0x001ca0a0 | Trn mode: 0x0000002b
[   27.642277] mmc2: sdhci: Present:   0x01f70106 | Host ctl: 0x00000035
[   27.648700] mmc2: sdhci: Power:     0x0000000f | Blk gap:  0x00000000
[   27.655124] mmc2: sdhci: Wake-up:   0x00000000 | Clock:    0x00000107
[   27.661547] mmc2: sdhci: Timeout:   0x0000000e | Int stat: 0x00000000
[   27.667971] mmc2: sdhci: Int enab:  0x03ff000b | Sig enab: 0x03ff000b
[   27.674394] mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000000
[   27.680818] mmc2: sdhci: Caps:      0x35fc0080 | Caps_1:   0x00002f77
[   27.687241] mmc2: sdhci: Cmd:       0x0000193a | Max curr: 0x00000000
[   27.693666] mmc2: sdhci: Resp[0]:   0x00000900 | Resp[1]:  0xfff6dbff
[   27.700088] mmc2: sdhci: Resp[2]:   0x320f5903 | Resp[3]:  0x00000900
[   27.706513] mmc2: sdhci: Host ctl2: 0x0000400d
[   27.710940] mmc2: sdhci: ADMA Err:  0x00000000 | ADMA Ptr: 0x02080208
[   27.717363] mmc2: sdhci: ============================================

Drop it will make emmc work again.. but I'm still unable to make SD card driver work,
that's probably another problem

I've took a look at current K3's sdhci driver, all operations on SPACEMIT_SDHC_OP_EXT_REG
register are used only when doing voltage switch with SD card, snip of the code from vendor

	if (host->mmc->caps2 & MMC_CAP2_NO_MMC) {
                /* sd/sdio has no phy */
                spacemit_sdhci_setbits(host, SDHC_TX_INT_CLK_SEL, SPACEMIT_SDHC_TX_CFG_REG);

        } else {
                /* use phy func mode */
                spacemit_sdhci_setbits(host, SDHC_PHY_FUNC_EN | SDHC_PHY_PLL_LOCK,
                                       SPACEMIT_SDHC_PHY_CTRL_REG);
                spacemit_sdhci_clrsetbits(host, SDHC_PHY_DRIVE_SEL,
                                          SDHC_RX_BIAS_CTRL |
                                          FIELD_PREP(SDHC_PHY_DRIVE_SEL, 4),
                                          SPACEMIT_SDHC_PHY_PADCFG_REG);
                /* mmc card mode */
                spacemit_sdhci_setbits(host, SDHC_MMC_CARD_MODE, SPACEMIT_SDHC_MMC_CTRL_REG);
        }

-- 
Yixun Lan (dlan)