[PATCH v3 3/3] riscv: dts: thead: Enable I2C on the BeagleV-Ahead

[Drew Fustini]

On Tue, Jun 18, 2024 at 09:42:40AM +0200, Thomas Bonnefille wrote:
> This commit enables the I2C0 controller of the TH1520, together with
> the FT24C32A EEPROM that is connected to it.
> In addition, this commit also enables the I2C controllers I2C2, I2C4
> and I2C5 as they are all three exposed on headers (P9 19 and 20 for I2C2,
> P9 17 and 18 for I2C5 and MikroBus 7 and 5 for I2C4).
> It also defined the required pinctrl nodes.
> 
> Signed-off-by: Thomas Bonnefille <thomas.bonnefille at bootlin.com>
> ---
>  arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts | 84 ++++++++++++++++++++++
>  1 file changed, 84 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
> index 57a2578123eb..b5c4f1811955 100644
> --- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
> +++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
> @@ -122,6 +122,19 @@ led-pins {
>  };
>  
>  &padctrl0_apsys {
> +	i2c2_pins: i2c2-0 {
> +		i2c-pins {
> +			pins = "I2C2_SDA",
> +			       "I2C2_SCL";
> +			function = "i2c";
> +			bias-pull-up = <48000>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +
>  	uart0_pins: uart0-0 {
>  		tx-pins {
>  			pins = "UART0_TXD";
> @@ -145,8 +158,79 @@ rx-pins {
>  	};
>  };
>  
> +&padctrl1_apsys {
> +	i2c0_pins: i2c0-0 {
> +		i2c-pins {
> +			pins = "I2C0_SDA",
> +			       "I2C0_SCL";
> +			function = "i2c";
> +			bias-pull-up = <48000>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +
> +	i2c4_pins: i2c4-0 {
> +		i2c-pins {
> +			pins = "GPIO0_19", /* I2C4_SDA */
> +			       "GPIO0_18"; /* I2C4_SCL */
> +			function = "i2c";
> +			bias-pull-up = <48000>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +
> +	i2c5_pins: i2c5-0 {
> +		i2c-pins {
> +			pins = "QSPI1_D0_MOSI", /* I2C5_SDA */
> +			       "QSPI1_CSN0";    /* I2C5_SCL */
> +			function = "i2c";
> +			bias-pull-up = <48000>;
> +			drive-strength = <7>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};
> +	};
> +};
> +
>  &uart0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart0_pins>;
>  	status = "okay";
>  };
> +
> +&i2c0 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c0_pins>;
> +	status = "okay";
> +
> +	eeprom at 50 {
> +		compatible = "atmel,24c32";
> +		reg = <0x50>;
> +	};
> +};
> +
> +&i2c2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c2_pins>;
> +	status = "okay";
> +};
> +
> +&i2c4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c4_pins>;
> +	status = "okay";
> +};
> +
> +&i2c5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&i2c5_pins>;
> +	status = "okay";
> +};
> 
> -- 
> 2.45.2
>

Reviewed-by: Drew Fustini <dfustini at tenstorrent.com>