[PATCH 1/2] riscv: dts: cv1800b: add pinctrl node for cv1800b

[Samuel Holland]

On 2023-11-12 6:57 PM, Jisheng Zhang wrote:
> Add the reset device tree node to cv1800b SoC reusing the
          ^^^^^
          I assume you mean pinctrl here?

> pinctrl-single driver.
> 
> Signed-off-by: Jisheng Zhang <jszhang at kernel.org>
> ---
>  arch/riscv/boot/dts/sophgo/cv-pinctrl.h | 19 +++++++++++++++++++
>  arch/riscv/boot/dts/sophgo/cv1800b.dtsi | 10 ++++++++++
>  2 files changed, 29 insertions(+)
>  create mode 100644 arch/riscv/boot/dts/sophgo/cv-pinctrl.h
> 
> diff --git a/arch/riscv/boot/dts/sophgo/cv-pinctrl.h b/arch/riscv/boot/dts/sophgo/cv-pinctrl.h
> new file mode 100644
> index 000000000000..ed78b6fb3142
> --- /dev/null
> +++ b/arch/riscv/boot/dts/sophgo/cv-pinctrl.h

A couple of questions: Should this go in include/dt-bindings? And is it worth
including macros for the actual function mappings, like in the vendor source[1]?

[1]:
https://github.com/milkv-duo/duo-buildroot-sdk/blob/develop/linux_5.10/drivers/pinctrl/cvitek/cv180x_pinlist_swconfig.h

> @@ -0,0 +1,19 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * This header provides constants for pinctrl bindings for Sophgo CV* SoC.
> + *
> + * Copyright (C) 2023 Jisheng Zhang <jszhang at kernel.org>
> + */
> +#ifndef _DTS_RISCV_SOPHGO_CV_PINCTRL_H
> +#define _DTS_RISCV_SOPHGO_CV_PINCTRL_H
> +
> +#define MUX_M0		0
> +#define MUX_M1		1
> +#define MUX_M2		2
> +#define MUX_M3		3
> +#define MUX_M4		4
> +#define MUX_M5		5
> +#define MUX_M6		6
> +#define MUX_M7		7
> +
> +#endif
> diff --git a/arch/riscv/boot/dts/sophgo/cv1800b.dtsi b/arch/riscv/boot/dts/sophgo/cv1800b.dtsi
> index e04df04a91c0..7a44d8e8672b 100644
> --- a/arch/riscv/boot/dts/sophgo/cv1800b.dtsi
> +++ b/arch/riscv/boot/dts/sophgo/cv1800b.dtsi
> @@ -6,6 +6,8 @@
>  #include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/reset/sophgo,cv1800b-reset.h>
>  
> +#include "cv-pinctrl.h"
> +
>  / {
>  	compatible = "sophgo,cv1800b";
>  	#address-cells = <1>;
> @@ -55,6 +57,14 @@ soc {
>  		dma-noncoherent;
>  		ranges;
>  
> +		pinctrl0: pinctrl at 3001000 {
> +			compatible = "pinctrl-single";
> +			reg = <0x3001000 0x130>;
> +			#pinctrl-cells = <1>;
> +			pinctrl-single,register-width = <32>;
> +			pinctrl-single,function-mask = <0x00000007>;
> +		};

>From the vendor driver[2], it looks like this peripheral block only handles
pinmuxing, so indeed this looks like a good use of pinctrl-single.

[2]:
https://github.com/milkv-duo/duo-buildroot-sdk/blob/develop/linux_5.10/drivers/pinctrl/cvitek/pinctrl-cv180x.h

> +
>  		rst: reset-controller at 3003000 {
>  			compatible = "sophgo,cv1800b-reset";
>  			reg = <0x03003000 0x1000>;