[PATCH 06/12] RISC-V: crypto: add accelerated AES-CBC/CTR/ECB/XTS implementations
Eric Biggers
ebiggers at kernel.org
Thu Nov 9 21:44:28 PST 2023
On Fri, Nov 10, 2023 at 12:58:12PM +0800, Andy Chiu wrote:
> Hi Eric,
>
> On Thu, Nov 9, 2023 at 3:16 PM Eric Biggers <ebiggers at kernel.org> wrote:
> >
> > On Tue, Nov 07, 2023 at 04:53:13PM +0800, Jerry Shih wrote:
> > > On Nov 2, 2023, at 13:16, Eric Biggers <ebiggers at kernel.org> wrote:
> > > > On Thu, Oct 26, 2023 at 02:36:38AM +0800, Jerry Shih wrote:
> > > >> +static int ecb_encrypt(struct skcipher_request *req)
> > > >> +{
> > > >> + struct crypto_skcipher *tfm = crypto_skcipher_reqtfm(req);
> > > >> + const struct riscv64_aes_ctx *ctx = crypto_skcipher_ctx(tfm);
> > > >> + struct skcipher_walk walk;
> > > >> + unsigned int nbytes;
> > > >> + int err;
> > > >> +
> > > >> + /* If we have error here, the `nbytes` will be zero. */
> > > >> + err = skcipher_walk_virt(&walk, req, false);
> > > >> + while ((nbytes = walk.nbytes)) {
> > > >> + kernel_vector_begin();
> > > >> + rv64i_zvkned_ecb_encrypt(walk.src.virt.addr, walk.dst.virt.addr,
> > > >> + nbytes & AES_BLOCK_VALID_SIZE_MASK,
> > > >> + &ctx->key);
> > > >> + kernel_vector_end();
> > > >> + err = skcipher_walk_done(
> > > >> + &walk, nbytes & AES_BLOCK_REMAINING_SIZE_MASK);
> > > >> + }
> > > >> +
> > > >> + return err;
> > > >> +}
> > > >
> > > > There's no fallback for !crypto_simd_usable() here. I really like it this way.
> > > > However, for it to work (for skciphers and aeads), RISC-V needs to allow the
> > > > vector registers to be used in softirq context. Is that already the case?
> > >
> > > The kernel-mode-vector could be enabled in softirq, but we don't have nesting
> > > vector contexts. Will we have the case that kernel needs to jump to softirq for
> > > encryptions during the regular crypto function? If yes, we need to have fallbacks
> > > for all algorithms.
> >
> > Are you asking what happens if a softirq is taken while the CPU is between
> > kernel_vector_begin() and kernel_vector_end()? I think that needs to be
> > prevented by making kernel_vector_begin() and kernel_vector_end() disable and
> > re-enable softirqs, like what kernel_neon_begin() and kernel_neon_end() do on
> > arm64. Refer to commit 13150149aa6ded which implemented that behavior on arm64.
>
> Yes, if making Vector available to softirq context is a must, then it
> is reasonable to call local_bh_disable() in kernel_vector_begin().
> However, softirq would not be the only user for Vector and disabling
> it may cause extra latencies. Meanwhile, simply disabling bh in
> kernel_vector_begin() will conflict with the patch[1] that takes an
> approach to run Preemptible Vector. Though it is not clear yet on
> whether we should run Vector without turning off preemption, I have
> tested running preemptible Vector and observed some latency
> improvements without sacrificing throughput. We will have a discussion
> on LPC2023[2] and it'd be great if you could join or continue to
> discuss it here.
>
> Approaches can be done such as nesting, if running Vector in softirq
> is required. Since it requires extra save/restore on nesting, I think
> we should run some tests to get more performance (latency/throughput)
> figure let the result decide the final direction. For example, we
> could run Vector in either nesting with preempt-V and non-nesting
> without preempt-V and compare the following performance catachristics:
> - System-wide latency impact
> - Latency and throughput of softirq-Vector itself
The skcipher and aead APIs do indeed need to work in softirq context.
It's possible to use a fallback, either by falling back to scalar instructions
or by punting the encryption/decryption operation to a workqueue using
crypto/simd.c. However, both approaches have some significant disadvantages.
It was nice that the need for them on arm64 was eliminated by commit
13150149aa6ded. Note that it's possible to yield the vector unit occasionally,
to keep preemption and softirqs from being disabled for too long.
- Eric
More information about the linux-riscv
mailing list