[PATCH v7 2/3] clocksource: Add JH7110 timer driver

[Xingyu Wu]

On 2023/10/27 21:34, Daniel Lezcano wrote:
> 
> On 27/10/2023 11:17, Xingyu Wu wrote:
>> On 2023/10/25 22:39, Daniel Lezcano wrote:
>>>
>>> Hi Xingyu,
>>>
>>>
>>> On 25/10/2023 11:04, Xingyu Wu wrote:
>>>> On 2023/10/24 22:56, Daniel Lezcano wrote:
>>>>>
>>>>> Hi Xingyu,
>>>>>
>>>>>
>>>>> On 19/10/2023 07:35, Xingyu Wu wrote:
>>>>>> Add timer driver for the StarFive JH7110 SoC.
>>>>>
>>>>> As it is a new timer, please add a proper nice description
>>>>> explaining the timer hardware, thanks.
>>>>
>>>> OK. Will add the description in next version.
>>>>
>>>>>
>>>>>> Signed-off-by: Xingyu Wu <xingyu.wu at starfivetech.com> --- MAINTAINERS                        |   7 + drivers/clocksource/Kconfig        |  11 + drivers/clocksource/Makefile       |   1 + drivers/clocksource/timer-jh7110.c | 380
>>>>>> +++++++++++++++++++++++++++++ 4 files changed, 399
>>>>>> insertions(+) create mode 100644
>>>>>> drivers/clocksource/timer-jh7110.c
>>>>>>
>>>>>> diff --git a/MAINTAINERS b/MAINTAINERS index
>>>>>> 7a7bd8bd80e9..91c09b399131 100644 --- a/MAINTAINERS +++
>>>>>> b/MAINTAINERS @@ -20473,6 +20473,13 @@ S:    Maintained F:
>>>>>> Documentation/devicetree/bindings/sound/starfive,jh7110-tdm.yaml
>>>>>>
>>>>>>
> F:    sound/soc/starfive/jh7110_tdm.c
>>>>>> +STARFIVE JH7110 TIMER DRIVER +M:    Samin Guo
>>>>>> <samin.guo at starfivetech.com> +M:    Xingyu Wu
>>>>>> <xingyu.wu at starfivetech.com> +S:    Supported +F:
>>>>>> Documentation/devicetree/bindings/timer/starfive,jh7110-timer.yaml
>>>>>>
>>>>>>
> +F:    drivers/clocksource/timer-jh7110.c
>>>>>> + STARFIVE JH71X0 CLOCK DRIVERS M:    Emil Renner Berthing
>>>>>> <kernel at esmil.dk> M:    Hal Feng <hal.feng at starfivetech.com> diff --git a/drivers/clocksource/Kconfig
>>>>>> b/drivers/clocksource/Kconfig index
>>>>>> 0ba0dc4ecf06..821abcc1e517 100644 ---
>>>>>> a/drivers/clocksource/Kconfig +++
>>>>>> b/drivers/clocksource/Kconfig @@ -641,6 +641,17 @@ config
>>>>>> RISCV_TIMER is accessed via both the SBI and the rdcycle
>>>>>> instruction.  This is required for all RISC-V systems. +config STARFIVE_JH7110_TIMER +    bool "Timer for the
>>>>>> STARFIVE JH7110 SoC" +    depends on ARCH_STARFIVE ||
>>>>>> COMPILE_TEST
>>>>>
>>>>> You may want to use ARCH_STARFIVE only if the platform can make
>>>>> this timer optional. Otherwise, set the option from the
>>>>> platform Kconfig and put the bool "bla bla" if COMPILE_TEST
>>>>
>>>> Yes, this timer only be used on the StarFive SoC. So I intend to
>>>> modify to this:
>>>>
>>>> bool "Timer for the STARFIVE JH7110 SoC" if COMPILE_TEST depends
>>>> on ARCH_STARFIVE
>>>
>>> In this case, you should change the platform config and select the
>>> timer from there. Remove the depends on ARCH_STARFIVE so it is
>>> possible enable cross test compilation. Otherwise COMPILE_TEST will
>>> not work on other platforms.
>>>
>>> [ ... ]
>>>
>>
>> It is not a kernel timer or clocksource. It will not work on other
>> platforms and is just used on the JH7110 SoC. I think I needn't
>> remove it. Maybe I modify to this:
>>
>> bool "Timer for the STARFIVE JH7110 SoC" if COMPILE_TEST depends on
>> ARCH_STARFIVE || COMPILE_TEST
> 
> I think there is a misunderstanding.
> 
> If we want to compile on x86 drivers for other platforms, we select COMPILE_TEST so we can enable the timer and do compilation testing.
> 
> In this case, we may want to compile the STARFIVE JH7110 on x86 just to double check it is correctly compiling (eg. we do changes impacting all the drivers). If the ARCH_STARFIVE dependency is set, then that won't be possible.
> 
> So it should be:
> 
> bool "Timer for the STARFIVE JH7110 SoC" if COMPILE_TEST
> ...
> 
> And in arch/riscv/Kconfig.socs
> 
> config SOC_STARFIVE
>     ...
>     select STARFIVE_JH7110_TIMER
>     ...
> 
>>>>>> +struct jh7110_clkevt { +    struct clock_event_device evt; +
>>>>>> struct clocksource cs; +    bool cs_is_valid; +    struct clk
>>>>>> *clk; +    struct reset_control *rst; +    u32 rate; +    u32
>>>>>> reload_val; +    void __iomem *base; +    char
>>>>>> name[sizeof("jh7110-timer.chX")]; +}; + +struct
>>>>>> jh7110_timer_priv { +    struct clk *pclk; +    struct
>>>>>> reset_control *prst; +    struct jh7110_clkevt
>>>>>> clkevt[JH7110_TIMER_CH_MAX];
>>>>>
>>>>> Why do you need several clock events and clock sources ?
>>>>
>>>> This timer has four counters (channels) which run independently.
>>>> So each counter can have its own clock event and clock source to
>>>> configure different settings.
>>>
>>> The kernel only needs one clocksource. Usually multiple clockevents
>>> are per-cpu based system.
>>>
>>> The driver does not seem to have a per cpu timer but just
>>> initializing multiple clockevents which will end up unused, wasting
>>> energy.
>>>
>>>
>>
>> The board of the StarFive JH7110 SoC has two types of timer :
>> riscv-timer and jh7110-timer. It boots by riscv-timer(clocksource)
>> and the jh7110-timer is optional and additional. I think I should
>> initialize the four channels of jh7110-timer as clockevents not
>> clocksource pre-cpu.
> 
> If no clocksource is needed on this SoC because riscv timers are used, then it is not useful to register a clocksource for this timer and the corresponding code can go away.
> 
> If the clockevent is optional why do you need this driver at all?
> 
> 
> 

Hi Daniel,

Sorry, maybe I didn't express it clearly enough. I use this jh7110-timer as a global timer on the SoC and riscv-timer as cpu local timer. So these are something different.

These four counters in this jh7110-timer are exactly the same and independent of each other. If this timer is used as a global timer, do I use only one or all of the counters to register clocksource and clockevent?

Thanks,
Xingyu Wu