[PATCH 06/11] RISC-V: drivers/iommu/riscv: Add command, fault, page-req queues

[Zong Li]

On Fri, Jul 21, 2023 at 2:00 AM Tomasz Jeznach <tjeznach at rivosinc.com> wrote:
>
> On Wed, Jul 19, 2023 at 8:12 PM Nick Kossifidis <mick at ics.forth.gr> wrote:
> >
> > Hello Tomasz,
> >
> > On 7/19/23 22:33, Tomasz Jeznach wrote:
> > > Enables message or wire signal interrupts for PCIe and platforms devices.
> > >
> >
> > The description doesn't match the subject nor the patch content (we
> > don't jus enable interrupts, we also init the queues).
> >
> > > +     /* Parse Queue lengts */
> > > +     ret = of_property_read_u32(pdev->dev.of_node, "cmdq_len", &iommu->cmdq_len);
> > > +     if (!ret)
> > > +             dev_info(dev, "command queue length set to %i\n", iommu->cmdq_len);
> > > +
> > > +     ret = of_property_read_u32(pdev->dev.of_node, "fltq_len", &iommu->fltq_len);
> > > +     if (!ret)
> > > +             dev_info(dev, "fault/event queue length set to %i\n", iommu->fltq_len);
> > > +
> > > +     ret = of_property_read_u32(pdev->dev.of_node, "priq_len", &iommu->priq_len);
> > > +     if (!ret)
> > > +             dev_info(dev, "page request queue length set to %i\n", iommu->priq_len);
> > > +
> > >       dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
> > >
> >
> > We need to add those to the device tree binding doc (or throw them away,
> > I thought it would be better to have them as part of the device
> > desciption than a module parameter).
> >
>
> We can add them as an optional fields to DT.
> Alternatively, I've been looking into an option to auto-scale CQ/PQ
> based on number of attached devices, but this gets trickier for
> hot-pluggable systems. I've added module parameters as a bare-minimum,
> but still looking for better solutions.
>
> >
> > > +static irqreturn_t riscv_iommu_priq_irq_check(int irq, void *data);
> > > +static irqreturn_t riscv_iommu_priq_process(int irq, void *data);
> > > +
> >
> > > +     case RISCV_IOMMU_PAGE_REQUEST_QUEUE:
> > > +             q = &iommu->priq;
> > > +             q->len = sizeof(struct riscv_iommu_pq_record);
> > > +             count = iommu->priq_len;
> > > +             irq = iommu->irq_priq;
> > > +             irq_check = riscv_iommu_priq_irq_check;
> > > +             irq_process = riscv_iommu_priq_process;
> > > +             q->qbr = RISCV_IOMMU_REG_PQB;
> > > +             q->qcr = RISCV_IOMMU_REG_PQCSR;
> > > +             name = "priq";
> > > +             break;
> >
> >
> > It makes more sense to add the code for the page request queue in the
> > patch that adds ATS/PRI support IMHO. This comment also applies to its
> > interrupt handlers below.
> >
>
> ack. will do.
>
> >
> > > +static inline void riscv_iommu_cmd_inval_set_addr(struct riscv_iommu_command *cmd,
> > > +                                               u64 addr)
> > > +{
> > > +     cmd->dword0 |= RISCV_IOMMU_CMD_IOTINVAL_AV;
> > > +     cmd->dword1 = addr;
> > > +}
> > > +
> >
> > This needs to be (addr >> 2) to match the spec, same as in the iofence
> > command.
> >
>
> oops. Thanks!
>

I think it should be (addr >> 12) according to the spec.

> > Regards,
> > Nick
> >
>
> regards,
> - Tomasz
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv