[PATCH 5/7] riscv: dts: bouffalolab: add the bl808 SoC base device tree

[Emil Renner Berthing]

On Mon, 21 Nov 2022 at 04:37, Icenowy Zheng <uwu at icenowy.me> wrote:
>
> 在 2022-11-20星期日的 15:57 +0100，Emil Renner Berthing写道：
> > On Sun, 20 Nov 2022 at 09:32, Jisheng Zhang <jszhang at kernel.org>
> > wrote:
> > >
> > > Add a baisc dtsi for the bouffalolab bl808 SoC.
> > >
> > > Signed-off-by: Jisheng Zhang <jszhang at kernel.org>
> > > ---
> > >  arch/riscv/boot/dts/Makefile               |  1 +
> > >  arch/riscv/boot/dts/bouffalolab/bl808.dtsi | 74
> > > ++++++++++++++++++++++
> > >  2 files changed, 75 insertions(+)
> > >  create mode 100644 arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > >
> > > diff --git a/arch/riscv/boot/dts/Makefile
> > > b/arch/riscv/boot/dts/Makefile
> > > index ff174996cdfd..b525467152b2 100644
> > > --- a/arch/riscv/boot/dts/Makefile
> > > +++ b/arch/riscv/boot/dts/Makefile
> > > @@ -1,4 +1,5 @@
> > >  # SPDX-License-Identifier: GPL-2.0
> > > +subdir-y += bouffalolab
> > >  subdir-y += sifive
> > >  subdir-y += starfive
> > >  subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > > diff --git a/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > > b/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > > new file mode 100644
> > > index 000000000000..c98ebb14ee10
> > > --- /dev/null
> > > +++ b/arch/riscv/boot/dts/bouffalolab/bl808.dtsi
> > > @@ -0,0 +1,74 @@
> > > +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> > > +/*
> > > + * Copyright (C) 2022 Jisheng Zhang <jszhang at kernel.org>
> > > + */
> > > +
> > > +#include <dt-bindings/interrupt-controller/irq.h>
> > > +
> > > +/ {
> > > +       compatible = "bouffalolab,bl808";
> > > +       #address-cells = <1>;
> > > +       #size-cells = <1>;
> > > +
> > > +       cpus {
> > > +               timebase-frequency = <1000000>;
> > > +               #address-cells = <1>;
> > > +               #size-cells = <0>;
> > > +
> > > +               cpu0: cpu at 0 {
> > > +                       compatible = "thead,c906", "riscv";
> > > +                       device_type = "cpu";
> > > +                       reg = <0>;
> > > +                       d-cache-block-size = <64>;
> > > +                       d-cache-sets = <256>;
> > > +                       d-cache-size = <32768>;
> > > +                       i-cache-block-size = <64>;
> > > +                       i-cache-sets = <128>;
> > > +                       i-cache-size = <32768>;
> > > +                       mmu-type = "riscv,sv39";
> > > +                       riscv,isa = "rv64imafdc";
> > > +
> > > +                       cpu0_intc: interrupt-controller {
> > > +                               compatible = "riscv,cpu-intc";
> > > +                               interrupt-controller;
> > > +                               #address-cells = <0>;
> > > +                               #interrupt-cells = <1>;
> > > +                       };
> > > +               };
> > > +       };
> > > +
> > > +       xtal: xtal-clk {
> > > +               compatible = "fixed-clock";
> > > +               clock-frequency = <40000000>;
> >
> > This was discussed many times before, but I think the conclusion was
> > that the frequency is a property of the crystal on the board, so this
> > should be 0 in the SoC dtsi, and then overwritten in the board device
> > tree.
>
> But many chips just specify an accepted frequency in their datasheet,
> and using a frequency other than this is undefined behavior.

Yes, this was the argument in previous discussions, but the conclusion
was still that it should go in the board dts. To be clear I'm just
summing up the conclusion from previous discussions about this, and
have no strong opinion other than we should do the same everywhere.

> >
> > > +               clock-output-names = "xtal";
> > > +               #clock-cells = <0>;
> > > +       };
> > > +
> > > +       soc {
> > > +               compatible = "simple-bus";
> > > +               ranges;
> > > +               interrupt-parent = <&plic>;
> > > +               dma-noncoherent;
> > > +               #address-cells = <1>;
> > > +               #size-cells = <1>;
> > > +
> > > +               uart0: serial at 30002000 {
> > > +                       compatible = "bouffalolab,uart";
> > > +                       reg = <0x30002000 0x1000>;
> > > +                       interrupts = <20 IRQ_TYPE_LEVEL_HIGH>;
> > > +                       clocks = <&xtal>;
> > > +                       status = "disabled";
> > > +               };
> > > +
> > > +               plic: interrupt-controller at e0000000 {
> > > +                       compatible = "thead,c900-plic";
> > > +                       reg = <0xe0000000 0x4000000>;
> > > +                       interrupts-extended = <&cpu0_intc
> > > 0xffffffff>,
> > > +                                             <&cpu0_intc 9>;
> > > +                       interrupt-controller;
> > > +                       #address-cells = <0>;
> > > +                       #interrupt-cells = <2>;
> > > +                       riscv,ndev = <64>;
> > > +               };
> > > +       };
> > > +};
> > > --
> > > 2.37.2
> > >
> > >
> > > _______________________________________________
> > > linux-riscv mailing list
> > > linux-riscv at lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-riscv
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>