[PATCH v2 6/9] net: phy: motorcomm: Add YT8531 phy support
Heiner Kallweit
hkallweit1 at gmail.com
Fri Dec 16 03:58:05 PST 2022
On 16.12.2022 08:06, Yanhong Wang wrote:
> This adds basic support for the Motorcomm YT8531
> Gigabit Ethernet PHY.
>
> Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
> ---
> drivers/net/phy/Kconfig | 3 +-
> drivers/net/phy/motorcomm.c | 202 ++++++++++++++++++++++++++++++++++++
> 2 files changed, 204 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
> index c57a0262fb64..86399254d9ff 100644
> --- a/drivers/net/phy/Kconfig
> +++ b/drivers/net/phy/Kconfig
> @@ -258,9 +258,10 @@ config MICROSEMI_PHY
>
> config MOTORCOMM_PHY
> tristate "Motorcomm PHYs"
> + default SOC_STARFIVE
Both are completely independent. This default should be removed.
> help
> Enables support for Motorcomm network PHYs.
> - Currently supports the YT8511 gigabit PHY.
> + Currently supports the YT8511 and YT8531 gigabit PHYs.
>
This doesn't apply. Parts of your patch exist already in net-next.
Support for YT8531S has been added in the meantime. Please rebase
your patch on net-next and annotate your patch as net-next.
> config NATIONAL_PHY
> tristate "National Semiconductor PHYs"
> diff --git a/drivers/net/phy/motorcomm.c b/drivers/net/phy/motorcomm.c
> index 7e6ac2c5e27e..bca03185b338 100644
> --- a/drivers/net/phy/motorcomm.c
> +++ b/drivers/net/phy/motorcomm.c
> @@ -3,13 +3,17 @@
> * Driver for Motorcomm PHYs
> *
> * Author: Peter Geis <pgwipeout at gmail.com>
> + *
> */
>
> +#include <linux/bitops.h>
> #include <linux/kernel.h>
> #include <linux/module.h>
> +#include <linux/of.h>
> #include <linux/phy.h>
>
> #define PHY_ID_YT8511 0x0000010a
> +#define PHY_ID_YT8531 0x4f51e91b
>
> #define YT8511_PAGE_SELECT 0x1e
> #define YT8511_PAGE 0x1f
> @@ -17,6 +21,10 @@
> #define YT8511_EXT_DELAY_DRIVE 0x0d
> #define YT8511_EXT_SLEEP_CTRL 0x27
>
> +#define YTPHY_EXT_SMI_SDS_PHY 0xa000
> +#define YTPHY_EXT_CHIP_CONFIG 0xa001
> +#define YTPHY_EXT_RGMII_CONFIG1 0xa003
> +
> /* 2b00 25m from pll
> * 2b01 25m from xtl *default*
> * 2b10 62.m from pll
> @@ -38,6 +46,51 @@
> #define YT8511_DELAY_FE_TX_EN (0xf << 12)
> #define YT8511_DELAY_FE_TX_DIS (0x2 << 12)
>
> +struct ytphy_reg_field {
> + char *name;
> + u32 mask;
> + u8 dflt; /* Default value */
> +};
> +
> +struct ytphy_priv_t {
> + u32 tx_inverted_1000;
> + u32 tx_inverted_100;
> + u32 tx_inverted_10;
> +};
> +
> +/* rx_delay_sel: RGMII rx clock delay train configuration, about 150ps per
> + * step. Delay = 150ps * N
> + *
> + * tx_delay_sel_fe: RGMII tx clock delay train configuration when speed is
> + * 100Mbps or 10Mbps, it's 150ps per step. Delay = 150ps * N
> + *
> + * tx_delay_sel: RGMII tx clock delay train configuration when speed is
> + * 1000Mbps, it's 150ps per step. Delay = 150ps * N
> + */
> +static const struct ytphy_reg_field ytphy_rxtxd_grp[] = {
> + { "rx_delay_sel", GENMASK(13, 10), 0x0 },
> + { "tx_delay_sel_fe", GENMASK(7, 4), 0xf },
> + { "tx_delay_sel", GENMASK(3, 0), 0x1 }
> +};
> +
> +/* tx_inverted_x: Use original or inverted RGMII TX_CLK to drive the RGMII
> + * TX_CLK delay train configuration when speed is
> + * xMbps(10/100/1000Mbps).
> + * 0: original, 1: inverted
> + */
> +static const struct ytphy_reg_field ytphy_txinver_grp[] = {
> + { "tx_inverted_1000", BIT(14), 0x0 },
> + { "tx_inverted_100", BIT(14), 0x0 },
> + { "tx_inverted_10", BIT(14), 0x0 }
Copy & Paste error that mask is the same for all entries?
> +};
> +
> +/* rxc_dly_en: RGMII clk 2ns delay control bit.
> + * 0: disable 1: enable
> + */
> +static const struct ytphy_reg_field ytphy_rxden_grp[] = {
> + { "rxc_dly_en", BIT(8), 0x1 }
> +};
> +
> static int yt8511_read_page(struct phy_device *phydev)
> {
> return __phy_read(phydev, YT8511_PAGE_SELECT);
> @@ -48,6 +101,33 @@ static int yt8511_write_page(struct phy_device *phydev, int page)
> return __phy_write(phydev, YT8511_PAGE_SELECT, page);
> };
>
> +static int ytphy_read_ext(struct phy_device *phydev, u32 regnum)
> +{
> + int ret;
> + int val;
> +
> + ret = __phy_write(phydev, YT8511_PAGE_SELECT, regnum);
> + if (ret < 0)
> + return ret;
> +
> + val = __phy_read(phydev, YT8511_PAGE);
> +
> + return val;
> +}
> +
> +static int ytphy_write_ext(struct phy_device *phydev, u32 regnum, u16 val)
> +{
> + int ret;
> +
> + ret = __phy_write(phydev, YT8511_PAGE_SELECT, regnum);
> + if (ret < 0)
> + return ret;
> +
> + ret = __phy_write(phydev, YT8511_PAGE, val);
> +
> + return ret;
> +}
> +
> static int yt8511_config_init(struct phy_device *phydev)
> {
> int oldpage, ret = 0;
> @@ -111,6 +191,116 @@ static int yt8511_config_init(struct phy_device *phydev)
> return phy_restore_page(phydev, oldpage, ret);
> }
>
> +static int ytphy_config_init(struct phy_device *phydev)
> +{
> + struct device_node *of_node;
> + u32 val;
> + u32 mask;
> + u32 cfg;
> + int ret;
> + int i = 0;
> +
> + of_node = phydev->mdio.dev.of_node;
> + if (of_node) {
> + ret = of_property_read_u32(of_node, ytphy_rxden_grp[0].name, &cfg);
> + if (!ret) {
> + mask = ytphy_rxden_grp[0].mask;
> + val = ytphy_read_ext(phydev, YTPHY_EXT_CHIP_CONFIG);
> +
> + /* check the cfg overflow or not */
> + cfg = cfg > mask >> (ffs(mask) - 1) ? mask : cfg;
> +
> + val &= ~mask;
> + val |= FIELD_PREP(mask, cfg);
> + ytphy_write_ext(phydev, YTPHY_EXT_CHIP_CONFIG, val);
This is the unlocked version. MDIO bus locking is missing.
> + }
> +
> + val = ytphy_read_ext(phydev, YTPHY_EXT_RGMII_CONFIG1);
> + for (i = 0; i < ARRAY_SIZE(ytphy_rxtxd_grp); i++) {
> + ret = of_property_read_u32(of_node, ytphy_rxtxd_grp[i].name, &cfg);
> + if (!ret) {
> + mask = ytphy_rxtxd_grp[i].mask;
> +
> + /* check the cfg overflow or not */
> + cfg = cfg > mask >> (ffs(mask) - 1) ? mask : cfg;
> +
> + val &= ~mask;
> + val |= cfg << (ffs(mask) - 1);
> + }
> + }
> + return ytphy_write_ext(phydev, YTPHY_EXT_RGMII_CONFIG1, val);
> + }
> +
> + phydev_err(phydev, "Get of node fail\n");
> +
Please consider that the PHY may be used on non-DT systems.
> + return -EINVAL;
> +}
> +
> +static void ytphy_link_change_notify(struct phy_device *phydev)
> +{
> + u32 val;
> + struct ytphy_priv_t *ytphy_priv = phydev->priv;
> +
> + if (phydev->speed < 0)
> + return;
> +
> + val = ytphy_read_ext(phydev, YTPHY_EXT_RGMII_CONFIG1);
> + switch (phydev->speed) {
> + case SPEED_1000:
> + val &= ~ytphy_txinver_grp[0].mask;
> + val |= FIELD_PREP(ytphy_txinver_grp[0].mask,
> + ytphy_priv->tx_inverted_1000);
> + break;
> +
> + case SPEED_100:
> + val &= ~ytphy_txinver_grp[1].mask;
> + val |= FIELD_PREP(ytphy_txinver_grp[1].mask,
> + ytphy_priv->tx_inverted_100);
> + break;
> +
> + case SPEED_10:
> + val &= ~ytphy_txinver_grp[2].mask;
> + val |= FIELD_PREP(ytphy_txinver_grp[2].mask,
> + ytphy_priv->tx_inverted_10);
> + break;
> +
> + default:
> + break;
> + }
> +
> + ytphy_write_ext(phydev, YTPHY_EXT_RGMII_CONFIG1, val);
> +}
> +
> +static int yt8531_probe(struct phy_device *phydev)
> +{
> + struct ytphy_priv_t *priv;
> + const struct device_node *of_node;
> + u32 val;
> + int ret;
> +
> + priv = devm_kzalloc(&phydev->mdio.dev, sizeof(*priv), GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + of_node = phydev->mdio.dev.of_node;
> + if (of_node) {
> + ret = of_property_read_u32(of_node, ytphy_txinver_grp[0].name, &val);
> + if (!ret)
> + priv->tx_inverted_1000 = val;
> +
> + ret = of_property_read_u32(of_node, ytphy_txinver_grp[1].name, &val);
> + if (!ret)
> + priv->tx_inverted_100 = val;
> +
> + ret = of_property_read_u32(of_node, ytphy_txinver_grp[2].name, &val);
> + if (!ret)
> + priv->tx_inverted_10 = val;
> + }
> + phydev->priv = priv;
> +
> + return 0;
> +}
> +
> static struct phy_driver motorcomm_phy_drvs[] = {
> {
> PHY_ID_MATCH_EXACT(PHY_ID_YT8511),
> @@ -120,6 +310,17 @@ static struct phy_driver motorcomm_phy_drvs[] = {
> .resume = genphy_resume,
> .read_page = yt8511_read_page,
> .write_page = yt8511_write_page,
> + }, {
> + PHY_ID_MATCH_EXACT(PHY_ID_YT8531),
> + .name = "YT8531 Gigabit Ethernet",
> + .probe = yt8531_probe,
> + .config_init = ytphy_config_init,
> + .read_status = genphy_read_status,
> + .suspend = genphy_suspend,
> + .resume = genphy_resume,
> + .read_page = yt8511_read_page,
> + .write_page = yt8511_write_page,
> + .link_change_notify = ytphy_link_change_notify,
> },
> };
>
> @@ -131,6 +332,7 @@ MODULE_LICENSE("GPL");
>
> static const struct mdio_device_id __maybe_unused motorcomm_tbl[] = {
> { PHY_ID_MATCH_EXACT(PHY_ID_YT8511) },
> + { PHY_ID_MATCH_EXACT(PHY_ID_YT8531) },
> { /* sentinal */ }
> };
>
More information about the linux-riscv
mailing list