[PATCH v2 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl

[Icenowy Zheng]

在 2022-11-18星期五的 09:11 +0800，Hal Feng写道：
> From: Jianlong Huang <jianlong.huang at starfivetech.com>
> 
> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
> 
> Signed-off-by: Jianlong Huang <jianlong.huang at starfivetech.com>
> Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
> ---
>  .../pinctrl/starfive,jh7110-sys-pinctrl.yaml  | 165
> ++++++++++++++++++
>  1 file changed, 165 insertions(+)
>  create mode 100644
> Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-
> pinctrl.yaml
> 
> diff --git
> a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-
> pinctrl.yaml
> b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-
> pinctrl.yaml
> new file mode 100644
> index 000000000000..79623f884a9c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-
> pinctrl.yaml
> @@ -0,0 +1,165 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id:
> http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: StarFive JH7110 Sys Pin Controller
> +
> +description: |
> +  Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
> +
> +  Out of the SoC's many pins only the ones named PAD_GPIO0 to
> PAD_GPIO63
> +  can be multiplexed and have configurable bias, drive strength,
> +  schmitt trigger etc.
> +  Some peripherals have their I/O go through the 64 "GPIOs". This
> also
> +  includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
> +  All these peripherals are connected to all 64 GPIOs such that
> +  any GPIO can be set up to be controlled by any of the peripherals.
> +
> +maintainers:
> +  - Jianlong Huang <jianlong.huang at starfivetech.com>
> +
> +properties:
> +  compatible:
> +    const: starfive,jh7110-sys-pinctrl
> +
> +  reg:
> +    maxItems: 1
> +
> +  reg-names:
> +    items:
> +      - const: control
> +
> +  clocks:
> +    maxItems: 1
> +
> +  resets:
> +    maxItems: 1
> +
> +  gpio-controller: true
> +
> +  "#gpio-cells":
> +    const: 2
> +
> +  interrupts:
> +    maxItems: 1
> +    description: The GPIO parent interrupt.
> +
> +  interrupt-controller: true
> +
> +  "#interrupt-cells":
> +    const: 2
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - clocks
> +  - gpio-controller
> +  - "#gpio-cells"
> +  - interrupts
> +  - interrupt-controller
> +  - "#interrupt-cells"
> +
> +patternProperties:
> +  '-[0-9]+$':
> +    type: object
> +    patternProperties:
> +      '-pins$':
> +        type: object
> +        description: |
> +          A pinctrl node should contain at least one subnode
> representing the
> +          pinctrl groups available on the machine. Each subnode will
> list the
> +          pins it needs, and how they should be configured, with
> regard to
> +          muxer configuration, system signal configuration, pin
> groups for
> +          vin/vout module, pin voltage, mux functions for output,
> mux functions
> +          for output enable, mux functions for input.

Could this handle hard wiring an internal input mux function to high or
low?

This feature is needed on the Star64 board to omit the USB overcurrent
pin.

> +
> +        properties:
> +          pinmux:
> +            description: |
> +              The list of GPIOs and their mux settings that
> properties in the
> +              node apply to. This should be set using the GPIOMUX
> macro.
> +            $ref: "/schemas/pinctrl/pinmux-
> node.yaml#/properties/pinmux"
> +
> +          bias-disable: true
> +
> +          bias-pull-up:
> +            type: boolean
> +
> +          bias-pull-down:
> +            type: boolean
> +
> +          drive-strength:
> +            enum: [ 2, 4, 8, 12 ]
> +
> +          input-enable: true
> +
> +          input-disable: true
> +
> +          input-schmitt-enable: true
> +
> +          input-schmitt-disable: true
> +
> +          slew-rate:
> +            maximum: 1
> +
> +        additionalProperties: false
> +
> +    additionalProperties: false
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/starfive-jh7110.h>
> +    #include <dt-bindings/reset/starfive-jh7110.h>
> +    #include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
> +
> +        soc {
> +                #address-cells = <2>;
> +                #size-cells = <2>;
> +
> +                gpio: gpio at 13040000 {
> +                        compatible = "starfive,jh7110-sys-pinctrl";
> +                        reg = <0x0 0x13040000 0x0 0x10000>;
> +                        reg-names = "control";
> +                        clocks = <&syscrg_clk JH7110_SYSCLK_IOMUX>;
> +                        resets = <&syscrg_rst JH7110_SYSRST_IOMUX>;
> +                        interrupts = <86>;
> +                        interrupt-controller;
> +                        #interrupt-cells = <2>;
> +                        #gpio-cells = <2>;
> +                        gpio-controller;
> +                        status = "okay";
> +
> +                        uart0_pins: uart0-0 {
> +                                tx-pins {
> +                                        pinmux = <GPIOMUX(5,
> GPOUT_SYS_UART0_TX, GPOEN_ENABLE, GPI_NONE)>;
> +                                        bias-disable;
> +                                        drive-strength = <12>;
> +                                        input-disable;
> +                                        input-schmitt-disable;
> +                                        slew-rate = <0>;
> +                                };
> +
> +                                rx-pins {
> +                                        pinmux = <GPIOMUX(6,
> GPOUT_LOW, GPOEN_DISABLE, GPI_SYS_UART0_RX)>;
> +                                        bias-pull-up;
> +                                        drive-strength = <2>;
> +                                        input-enable;
> +                                        input-schmitt-enable;
> +                                        slew-rate = <0>;
> +                                };
> +                        };
> +                };
> +
> +                uart0 {
> +                        pinctrl-names = "default";
> +                        pinctrl-0 = <&uart0_pins>;
> +                        status = "okay";
> +                };
> +        };
> +
> +...