[PATCH v1 7/7] riscv: dts: starfive: visionfive-v2: Add phy delay_chain configuration

[yanhong wang]

On 2022/12/2 1:49, Conor Dooley wrote:
> On Thu, Dec 01, 2022 at 05:02:42PM +0800, Yanhong Wang wrote:
>> Add phy delay_chain configuration to support motorcomm phy driver for
>> StarFive VisionFive 2 board.
>> 
>> Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
>> ---
>>  .../jh7110-starfive-visionfive-v2.dts         | 46 +++++++++++++++++++
>>  1 file changed, 46 insertions(+)
>> 
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
>> index c8946cf3a268..2868ef4c74ef 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
>> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-v2.dts
>> @@ -15,6 +15,8 @@
>>  
>>  	aliases {
>>  		serial0 = &uart0;
>> +		ethernet0=&gmac0;
>> +		ethernet1=&gmac1;
> 
> Please match the whitespace usage of the existing entry.
> 

Will fix in the next version.

>>  	};
>>  
>>  	chosen {
>> @@ -114,3 +116,47 @@
>>  	pinctrl-0 = <&uart0_pins>;
>>  	status = "okay";
>>  };
>> +
>> +&gmac0 {
>> +	status = "okay";
>> +	#address-cells = <1>;
>> +	#size-cells = <0>;
>> +	phy-handle = <&phy0>;
>> +	status = "okay";
>> +	mdio0 {
> 
> A line of whitespace before the child nodes too please :)
> 

Will fix.

>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		compatible = "snps,dwmac-mdio";
>> +		phy0: ethernet-phy at 0 {
>> +			reg = <0>;
>> +			rxc_dly_en = <1>;
>> +			tx_delay_sel_fe = <5>;
>> +			tx_delay_sel = <0xa>;
>> +			tx_inverted_10 = <0x1>;
>> +			tx_inverted_100 = <0x1>;
>> +			tx_inverted_1000 = <0x1>;
>> +		};
>> +	};
>> +};
>> +
>> +&gmac1 {
>> +	status = "okay";
>> +	#address-cells = <1>;
>> +	#size-cells = <0>;
>> +	phy-handle = <&phy1>;
>> +	status = "okay";
>> +	mdio1 {
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
>> +		compatible = "snps,dwmac-mdio";
>> +		phy1: ethernet-phy at 1 {
>> +			reg = <1>;
>> +			tx_delay_sel_fe = <5>;
>> +			tx_delay_sel = <0>;
>> +			rxc_dly_en = <0>;
>> +			tx_inverted_10 = <0x1>;
>> +			tx_inverted_100 = <0x1>;
>> +			tx_inverted_1000 = <0x0>;
>> +		};
>> +	};
>> +};
>> -- 
>> 2.17.1
>>