[PATCH v3 06/12] riscv: dts: allwinner: Add Allwinner D1 Nezha devicetree

[Samuel Holland]

"D1 Nezha" is Allwinner's first-party development board for the D1 SoC.
It was shipped with 512M, 1G, or 2G of DDR3. It supports onboard audio,
HDMI, gigabit Ethernet, WiFi and Bluetooth, USB 2.0 host and OTG ports,
plus low-speed I/O from the SoC and a GPIO expander chip.

Acked-by: Jernej Skrabec <jernej.skrabec at gmail.com>
Acked-by: Palmer Dabbelt <palmer at rivosinc.com>
Reviewed-by: Guo Ren <guoren at kernel.org>
Reviewed-by: Heiko Stuebner <heiko at sntech.de>
Tested-by: Conor Dooley <conor.dooley at microchip.com>
Tested-by: Heiko Stuebner <heiko at sntech.de>
Signed-off-by: Samuel Holland <samuel at sholland.org>
---

Changes in v3:
 - Drop mmc alias

Changes in v2:
 - Common regulators moved to MangoPi MQ patch, removed analog LDOs
 - Removed LRADC (depends on analog LDOs)
 - Added XR829 host-wake interrupt

 arch/riscv/boot/dts/allwinner/Makefile        |   1 +
 .../boot/dts/allwinner/sun20i-d1-nezha.dts    | 166 ++++++++++++++++++
 2 files changed, 167 insertions(+)
 create mode 100644 arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts

diff --git a/arch/riscv/boot/dts/allwinner/Makefile b/arch/riscv/boot/dts/allwinner/Makefile
index 2f2792594f7d..277e59d1c907 100644
--- a/arch/riscv/boot/dts/allwinner/Makefile
+++ b/arch/riscv/boot/dts/allwinner/Makefile
@@ -1,2 +1,3 @@
 # SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1-nezha.dtb
 dtb-$(CONFIG_ARCH_SUNXI) += sun20i-d1s-mangopi-mq.dtb
diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
new file mode 100644
index 000000000000..a0769185be97
--- /dev/null
+++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: (GPL-2.0+ or MIT)
+// Copyright (C) 2021-2022 Samuel Holland <samuel at sholland.org>
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/dts-v1/;
+
+#include "sun20i-d1.dtsi"
+#include "sun20i-common-regulators.dtsi"
+
+/ {
+	model = "Allwinner D1 Nezha";
+	compatible = "allwinner,d1-nezha", "allwinner,sun20i-d1";
+
+	aliases {
+		ethernet0 = &emac;
+		ethernet1 = &xr829;
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usbvbus: usbvbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usbvbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
+		enable-active-high;
+		vin-supply = <&reg_vcc>;
+	};
+
+	/*
+	 * This regulator is PWM-controlled, but the PWM controller is not
+	 * yet supported, so fix the regulator to its default voltage.
+	 */
+	reg_vdd_cpu: vdd-cpu {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd-cpu";
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&reg_vcc>;
+	};
+
+	wifi_pwrseq: wifi-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 6 12 GPIO_ACTIVE_LOW>; /* PG12 */
+	};
+};
+
+&cpu0 {
+	cpu-supply = <&reg_vdd_cpu>;
+};
+
+&dcxo {
+	clock-frequency = <24000000>;
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&emac {
+	pinctrl-0 = <&rgmii_pe_pins>;
+	pinctrl-names = "default";
+	phy-handle = <&ext_rgmii_phy>;
+	phy-mode = "rgmii-id";
+	phy-supply = <&reg_vcc_3v3>;
+	status = "okay";
+};
+
+&i2c2 {
+	pinctrl-0 = <&i2c2_pb0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pcf8574a: gpio at 38 {
+		compatible = "nxp,pcf8574a";
+		reg = <0x38>;
+		interrupt-parent = <&pio>;
+		interrupts = <1 2 IRQ_TYPE_LEVEL_LOW>; /* PB2 */
+		interrupt-controller;
+		gpio-controller;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+	};
+};
+
+&mdio {
+	ext_rgmii_phy: ethernet-phy at 1 {
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <1>;
+	};
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+	disable-wp;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&mmc1 {
+	bus-width = <4>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	non-removable;
+	vmmc-supply = <&reg_vcc_3v3>;
+	vqmmc-supply = <&reg_vcc_3v3>;
+	pinctrl-0 = <&mmc1_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	xr829: wifi at 1 {
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 */
+		interrupt-names = "host-wake";
+	};
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&uart0 {
+	pinctrl-0 = <&uart0_pb8_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&uart1 {
+	uart-has-rtscts;
+	pinctrl-0 = <&uart1_pg6_pins>, <&uart1_pg8_rts_cts_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* XR829 bluetooth is connected here */
+};
+
+&usb_otg {
+	dr_mode = "otg";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_id_det-gpios = <&pio 3 21 GPIO_ACTIVE_HIGH>; /* PD21 */
+	usb0_vbus_det-gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
+	usb0_vbus-supply = <&reg_usbvbus>;
+	usb1_vbus-supply = <&reg_vcc>;
+	status = "okay";
+};
-- 
2.37.4