[PATCH v5 2/6] phy: cdns-dphy: Add Rx support
Paul Kocialkowski
paul.kocialkowski at bootlin.com
Thu Sep 16 03:22:54 PDT 2021
Hi,
On Fri 03 Sep 21, 00:25, Pratyush Yadav wrote:
> The Cadence DPHY can be used to receive image data over the CSI-2
> protocol. Add support for Rx mode. The programming sequence differs from
> the Tx mode so it is added as a separate set of hooks to isolate the two
> paths. The mode in which the DPHY has to be used is selected based on
> the compatible.
I just realized that I didn't follow-up on a previous revision on the debate
about using the phy sub-mode to distinguish between rx/tx.
I see that you've been using a dedicated compatible, but I'm not sure this is a
good fit either. My understanding is that the compatible should describe a group
of register-compatible revisions of a hardware component, not how the hardware
is used specifically. I guess the distinction between rx/tx falls under
the latter rather than the former.
I just sent out a patch in my Allwinner MIPI CSI-2+ISP series adding
a specific direction property:
- https://lists.infradead.org/pipermail/linux-phy/2021-September/001420.html
- https://lists.infradead.org/pipermail/linux-phy/2021-September/001421.html
Which I feel is a more appropriate solution to implement the distinction.
What do you think?
Cheers,
Paul
> Signed-off-by: Pratyush Yadav <p.yadav at ti.com>
>
> ---
>
> Changes in v5:
> - Use the new cdns_dphy_info to specify PHY ops.
> - Re-order include in alphabetical order.
> - Make bands const.
> - Drop num_bands.
> - Make i, lanes unsigned.
> - Drop the maximum check in cdns_dphy_rx_get_band_ctrl(). Let the loop
> complete and return -EOPNOTSUPP when we reach the end.
> - Drop the "rate < bands[i].min_rate" check since the bands are in
> ascending order.
> - Move data_lane_ctrl to start of function and make it static const.
>
> Changes in v4:
> - Drop the submode parts. Use a different compatible for the Rx ops.
> - Make bands and num_bands static.
>
> Changes in v3:
> - Use a table to select the band.
> - Use a table to poll the data lane ready bits.
> - Multiply the DPHY HS clock rate by 2 to get the bit rate since the
> clock is DDR.
>
> drivers/phy/cadence/cdns-dphy.c | 182 ++++++++++++++++++++++++++++++++
> 1 file changed, 182 insertions(+)
>
> diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
> index e2c2b27c6539..9a4c1c684e9a 100644
> --- a/drivers/phy/cadence/cdns-dphy.c
> +++ b/drivers/phy/cadence/cdns-dphy.c
> @@ -1,11 +1,14 @@
> // SPDX-License-Identifier: GPL-2.0+
> /*
> * Copyright: 2017-2018 Cadence Design Systems, Inc.
> + * Copyright (C) 2021 Texas Instruments Incorporated - https://www.ti.com/
> */
>
> +#include <linux/bitfield.h>
> #include <linux/bitops.h>
> #include <linux/clk.h>
> #include <linux/io.h>
> +#include <linux/iopoll.h>
> #include <linux/module.h>
> #include <linux/of_address.h>
> #include <linux/of_device.h>
> @@ -25,10 +28,14 @@
> #define DPHY_PMA_RCLK(reg) (0x600 + (reg))
> #define DPHY_PMA_RDATA(lane, reg) (0x700 + ((lane) * 0x100) + (reg))
> #define DPHY_PCS(reg) (0xb00 + (reg))
> +#define DPHY_ISO(reg) (0xc00 + (reg))
>
> #define DPHY_CMN_SSM DPHY_PMA_CMN(0x20)
> #define DPHY_CMN_SSM_EN BIT(0)
> +#define DPHY_CMN_RX_BANDGAP_TIMER_MASK GENMASK(8, 1)
> #define DPHY_CMN_TX_MODE_EN BIT(9)
> +#define DPHY_CMN_RX_MODE_EN BIT(10)
> +#define DPHY_CMN_RX_BANDGAP_TIMER 0x14
>
> #define DPHY_CMN_PWM DPHY_PMA_CMN(0x40)
> #define DPHY_CMN_PWM_DIV(x) ((x) << 20)
> @@ -45,10 +52,27 @@
> #define DPHY_CMN_OPDIV_FROM_REG BIT(6)
> #define DPHY_CMN_OPDIV(x) ((x) << 7)
>
> +#define DPHY_BAND_CFG DPHY_PCS(0x0)
> +#define DPHY_BAND_CFG_LEFT_BAND GENMASK(4, 0)
> +#define DPHY_BAND_CFG_RIGHT_BAND GENMASK(9, 5)
> +
> #define DPHY_PSM_CFG DPHY_PCS(0x4)
> #define DPHY_PSM_CFG_FROM_REG BIT(0)
> #define DPHY_PSM_CLK_DIV(x) ((x) << 1)
>
> +#define DPHY_POWER_ISLAND_EN_DATA DPHY_PCS(0x8)
> +#define DPHY_POWER_ISLAND_EN_DATA_VAL 0xaaaaaaaa
> +#define DPHY_POWER_ISLAND_EN_CLK DPHY_PCS(0xc)
> +#define DPHY_POWER_ISLAND_EN_CLK_VAL 0xaa
> +
> +#define DPHY_ISO_CL_CTRL_L DPHY_ISO(0x10)
> +#define DPHY_ISO_DL_CTRL_L0 DPHY_ISO(0x14)
> +#define DPHY_ISO_DL_CTRL_L1 DPHY_ISO(0x20)
> +#define DPHY_ISO_DL_CTRL_L2 DPHY_ISO(0x30)
> +#define DPHY_ISO_DL_CTRL_L3 DPHY_ISO(0x3c)
> +#define DPHY_ISO_LANE_READY_BIT 0
> +#define DPHY_ISO_LANE_READY_TIMEOUT_MS 100UL
> +
> #define DSI_HBP_FRAME_OVERHEAD 12
> #define DSI_HSA_FRAME_OVERHEAD 14
> #define DSI_HFP_FRAME_OVERHEAD 6
> @@ -57,6 +81,9 @@
> #define DSI_NULL_FRAME_OVERHEAD 6
> #define DSI_EOT_PKT_SIZE 4
>
> +#define DPHY_LANES_MIN 1
> +#define DPHY_LANES_MAX 4
> +
> struct cdns_dphy_cfg {
> u8 pll_ipdiv;
> u8 pll_opdiv;
> @@ -105,6 +132,20 @@ struct cdns_dphy {
> struct phy *phy;
> };
>
> +struct cdns_dphy_rx_band {
> + unsigned int min_rate;
> + unsigned int max_rate;
> +};
> +
> +/* Order of bands is important since the index is the band number. */
> +static const struct cdns_dphy_rx_band bands[] = {
> + {80, 100}, {100, 120}, {120, 160}, {160, 200}, {200, 240},
> + {240, 280}, {280, 320}, {320, 360}, {360, 400}, {400, 480},
> + {480, 560}, {560, 640}, {640, 720}, {720, 800}, {800, 880},
> + {880, 1040}, {1040, 1200}, {1200, 1350}, {1350, 1500}, {1500, 1750},
> + {1750, 2000}, {2000, 2250}, {2250, 2500}
> +};
> +
> static int cdns_dsi_get_dphy_pll_cfg(struct cdns_dphy *dphy,
> struct cdns_dphy_cfg *cfg,
> struct phy_configure_opts_mipi_dphy *opts,
> @@ -360,6 +401,145 @@ static const struct cdns_dphy_info tx_ref_info = {
> .tx_ops = &tx_ref_dphy_ops,
> };
>
> +static int cdns_dphy_rx_power_on(struct phy *phy)
> +{
> + struct cdns_dphy *dphy = phy_get_drvdata(phy);
> +
> + /* Start RX state machine. */
> + writel(DPHY_CMN_SSM_EN | DPHY_CMN_RX_MODE_EN |
> + FIELD_PREP(DPHY_CMN_RX_BANDGAP_TIMER_MASK,
> + DPHY_CMN_RX_BANDGAP_TIMER),
> + dphy->regs + DPHY_CMN_SSM);
> +
> + return 0;
> +}
> +
> +static int cdns_dphy_rx_power_off(struct phy *phy)
> +{
> + struct cdns_dphy *dphy = phy_get_drvdata(phy);
> +
> + writel(0, dphy->regs + DPHY_CMN_SSM);
> +
> + return 0;
> +}
> +
> +static int cdns_dphy_rx_get_band_ctrl(unsigned long hs_clk_rate)
> +{
> + unsigned int rate, i;
> +
> + rate = hs_clk_rate / 1000000UL;
> + /* Since CSI-2 clock is DDR, the bit rate is twice the clock rate. */
> + rate *= 2;
> +
> + if (rate < bands[0].min_rate)
> + return -EOPNOTSUPP;
> +
> + for (i = 0; i < ARRAY_SIZE(bands); i++) {
> + if (rate < bands[i].max_rate)
> + return i;
> + }
> +
> + return -EOPNOTSUPP;
> +}
> +
> +static int cdns_dphy_rx_wait_for_bit(void __iomem *addr, unsigned int bit)
> +{
> + u32 val;
> +
> + return readl_relaxed_poll_timeout(addr, val, val & BIT(bit), 10,
> + DPHY_ISO_LANE_READY_TIMEOUT_MS * 1000);
> +}
> +
> +static int cdns_dphy_rx_wait_lane_ready(struct cdns_dphy *dphy,
> + unsigned int lanes)
> +{
> + static const u32 data_lane_ctrl[] = {DPHY_ISO_DL_CTRL_L0,
> + DPHY_ISO_DL_CTRL_L1,
> + DPHY_ISO_DL_CTRL_L2,
> + DPHY_ISO_DL_CTRL_L3};
> + void __iomem *reg = dphy->regs;
> + unsigned int i;
> + int ret;
> +
> + /* Data lanes. Minimum one lane is mandatory. */
> + if (lanes < DPHY_LANES_MIN || lanes > DPHY_LANES_MAX)
> + return -EINVAL;
> +
> + /* Clock lane */
> + ret = cdns_dphy_rx_wait_for_bit(reg + DPHY_ISO_CL_CTRL_L,
> + DPHY_ISO_LANE_READY_BIT);
> + if (ret)
> + return ret;
> +
> + for (i = 0; i < lanes; i++) {
> + ret = cdns_dphy_rx_wait_for_bit(reg + data_lane_ctrl[i],
> + DPHY_ISO_LANE_READY_BIT);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int cdns_dphy_rx_configure(struct phy *phy,
> + union phy_configure_opts *opts)
> +{
> + struct cdns_dphy *dphy = phy_get_drvdata(phy);
> + unsigned int reg;
> + int band_ctrl, ret;
> +
> + band_ctrl = cdns_dphy_rx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
> + if (band_ctrl < 0)
> + return band_ctrl;
> +
> + reg = FIELD_PREP(DPHY_BAND_CFG_LEFT_BAND, band_ctrl) |
> + FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, band_ctrl);
> + writel(reg, dphy->regs + DPHY_BAND_CFG);
> +
> + /*
> + * Set the required power island phase 2 time. This is mandated by DPHY
> + * specs.
> + */
> + reg = DPHY_POWER_ISLAND_EN_DATA_VAL;
> + writel(reg, dphy->regs + DPHY_POWER_ISLAND_EN_DATA);
> + reg = DPHY_POWER_ISLAND_EN_CLK_VAL;
> + writel(reg, dphy->regs + DPHY_POWER_ISLAND_EN_CLK);
> +
> + ret = cdns_dphy_rx_wait_lane_ready(dphy, opts->mipi_dphy.lanes);
> + if (ret) {
> + dev_err(dphy->dev, "DPHY wait for lane ready timeout\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int cdns_dphy_rx_validate(struct phy *phy, enum phy_mode mode,
> + int submode, union phy_configure_opts *opts)
> +{
> + int ret;
> +
> + if (mode != PHY_MODE_MIPI_DPHY)
> + return -EINVAL;
> +
> + ret = cdns_dphy_rx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
> + if (ret < 0)
> + return ret;
> +
> + return phy_mipi_dphy_config_validate(&opts->mipi_dphy);
> +}
> +
> +static const struct phy_ops rx_ref_phy_ops = {
> + .power_on = cdns_dphy_rx_power_on,
> + .power_off = cdns_dphy_rx_power_off,
> + .configure = cdns_dphy_rx_configure,
> + .validate = cdns_dphy_rx_validate,
> +};
> +
> +static const struct cdns_dphy_info rx_ref_info = {
> + .phy_ops = &rx_ref_phy_ops,
> +};
> +
> static int cdns_dphy_probe(struct platform_device *pdev)
> {
> struct phy_provider *phy_provider;
> @@ -417,6 +597,7 @@ static int cdns_dphy_remove(struct platform_device *pdev)
>
> static const struct of_device_id cdns_dphy_of_match[] = {
> { .compatible = "cdns,dphy", .data = &tx_ref_info },
> + { .compatible = "cdns,dphy-rx", .data = &rx_ref_info },
> { /* sentinel */ },
> };
> MODULE_DEVICE_TABLE(of, cdns_dphy_of_match);
> @@ -432,5 +613,6 @@ static struct platform_driver cdns_dphy_platform_driver = {
> module_platform_driver(cdns_dphy_platform_driver);
>
> MODULE_AUTHOR("Maxime Ripard <maxime.ripard at bootlin.com>");
> +MODULE_AUTHOR("Pratyush Yadav <p.yadav at ti.com>");
> MODULE_DESCRIPTION("Cadence MIPI D-PHY Driver");
> MODULE_LICENSE("GPL");
> --
> 2.33.0
>
--
Paul Kocialkowski, Bootlin
Embedded Linux and kernel engineering
https://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-phy/attachments/20210916/1de5ea97/attachment.sig>
More information about the linux-phy
mailing list