[Linux-parport] [RFC] remove the paride driver
Christoph Hellwig
hch at lst.de
Wed Feb 2 06:13:40 PST 2022
On Sun, Jan 30, 2022 at 09:14:43PM +0100, Ondrej Zary wrote:
> Here's the first version that works somehow. Detected LS-120 drive (epat) and
> even mounted the filesystem and copied files! The code is crap (missing error
> handling, unclaim/dicconnect, unregister, oopses on reboot, etc.).
>
> The pata_parport_* functions are copied from libata-sff.c and modified not to
> use ioread/iowrite. The pi_* functions are copied from paride.c and slightly
> modified. The original paride protocol modules can register without any
> changes.
Nice!
> I'm not sure about the device model integration (required by libata?).
> It currently registers "pata_parport" bus with a "new_device" sysfs file
> which is used to create new devices. I wonder if it's the correct way - it's
> not possible to simply modprobe something with parameters to get a working
> drive.
Not sure. Maybe Damien as the new libata maintainer has any idea what
to best do about that.
>
> [ 130.605256] paride: epat registered as protocol 0
> [ 132.363939] xxx: 0x378 is parport0
> [ 132.374746] xxx: epat: port 0x378, mode 0, ccr 0, test=(0,256,0)
> [ 132.374777] xxx: Sharing parport0 at 0x378
> [ 132.374918] xxx: epat 1.02, Shuttle EPAT chip c6 at 0x378,
> [ 132.374922] mode 0 (4-bit), delay 0
> [ 132.374950] pi_init ok!
> [ 132.377377] alloc_ok!
> [ 132.394447] scsi host4: pata_parport
> [ 132.394623] ata5: PATA max PIO0
> [ 132.613339] ata5.00: ATAPI: LS-120 COSM 04 UHD Floppy, 0270M09T, max PIO2
> [ 132.694550] scsi 4:0:0:0: Direct-Access MATSHITA LS-120 COSM 04 0270 PQ: 0 ANSI: 5
> [ 132.729748] sd 4:0:0:0: Attached scsi generic sg1 type 0
> [ 132.760779] sd 4:0:0:0: [sdb] Media removed, stopped polling
> [ 132.792602] sd 4:0:0:0: [sdb] Attached SCSI removable disk
> [ 151.142037] sd 4:0:0:0: [sdb] Read Capacity(16) failed: Result: hostbyte=DID_ERROR driverbyte=DRIVER_OK
> [ 151.142090] sd 4:0:0:0: [sdb] Sense not available.
> [ 151.204874] sd 4:0:0:0: [sdb] 246528 512-byte logical blocks: (126 MB/120 MiB)
> [ 151.226471] sd 4:0:0:0: [sdb] Write Protect is on
> [ 151.226514] sd 4:0:0:0: [sdb] Mode Sense: 00 66 31 80
> [ 151.320880] sdb: detected capacity change from 0 to 246528
> [ 152.090211] sdb:
>
> From ddfc09664e5800c57cda4908ccf1ba4db92e94c4 Mon Sep 17 00:00:00 2001
> From: Ondrej Zary <linux at zary.sk>
> Date: Sun, 30 Jan 2022 21:09:39 +0100
> Subject: [PATCH] pata_parport: first preview
>
> ---
> drivers/ata/Kconfig | 6 +
> drivers/ata/Makefile | 2 +
> drivers/ata/pata_parport.c | 688 +++++++++++++++++++++++++++++++++++++
> 3 files changed, 696 insertions(+)
> create mode 100644 drivers/ata/pata_parport.c
>
> diff --git a/drivers/ata/Kconfig b/drivers/ata/Kconfig
> index cb54631fd950..f2e130ff67d9 100644
> --- a/drivers/ata/Kconfig
> +++ b/drivers/ata/Kconfig
> @@ -1161,6 +1161,12 @@ config PATA_WINBOND_VLB
> Support for the Winbond W83759A controller on Vesa Local Bus
> systems.
>
> +config PATA_PARPORT
> + tristate "Parallel port IDE device support"
> + depends on PARPORT_PC
> + help
> + Support for Parallel port IDE devices.
> +
> comment "Generic fallback / legacy drivers"
>
> config PATA_ACPI
> diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
> index b8aebfb14e82..77145834a585 100644
> --- a/drivers/ata/Makefile
> +++ b/drivers/ata/Makefile
> @@ -114,6 +114,8 @@ obj-$(CONFIG_PATA_SAMSUNG_CF) += pata_samsung_cf.o
>
> obj-$(CONFIG_PATA_PXA) += pata_pxa.o
>
> +obj-$(CONFIG_PATA_PARPORT) += pata_parport.o
> +
> # Should be last but two libata driver
> obj-$(CONFIG_PATA_ACPI) += pata_acpi.o
> # Should be last but one libata driver
> diff --git a/drivers/ata/pata_parport.c b/drivers/ata/pata_parport.c
> new file mode 100644
> index 000000000000..1edbbe9d9687
> --- /dev/null
> +++ b/drivers/ata/pata_parport.c
> @@ -0,0 +1,688 @@
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/libata.h>
> +#include <linux/parport.h>
> +#include "paride.h"
> +
> +#define DRV_NAME "pata_parport"
> +
> +#define MAX_PROTOS 32
> +static struct pi_protocol *protocols[MAX_PROTOS];
> +
> +static unsigned int pata_parport_devchk(struct ata_port *ap, unsigned int device)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> + u8 nsect, lbal;
> +
> + ap->ops->sff_dev_select(ap, device);
> +
> + pi->proto->write_regr(pi, 0, ATA_REG_NSECT, 0x55);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAL, 0xaa);
> +
> + pi->proto->write_regr(pi, 0, ATA_REG_NSECT, 0xaa);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAL, 0x55);
> +
> + pi->proto->write_regr(pi, 0, ATA_REG_NSECT, 055);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAL, 0xaa);
> +
> + nsect = pi->proto->read_regr(pi, 0, ATA_REG_NSECT);
> + lbal = pi->proto->read_regr(pi, 0, ATA_REG_LBAL);
> +
> + if ((nsect == 0x55) && (lbal == 0xaa))
> + return 1; /* we found a device */
> +
> + return 0; /* nothing found */
> +}
> +
> +static int pata_parport_bus_softreset(struct ata_port *ap, unsigned int devmask,
> + unsigned long deadline)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> + /* software reset. causes dev0 to be selected */
> + pi->proto->write_regr(pi, 1, 6, ap->ctl);
> + udelay(20); /* FIXME: flush */
> + pi->proto->write_regr(pi, 1, 6, ap->ctl | ATA_SRST);
> + udelay(20); /* FIXME: flush */
> + pi->proto->write_regr(pi, 1, 6, ap->ctl);
> + ap->last_ctl = ap->ctl;
> +
> + /* wait the port to become ready */
> + return ata_sff_wait_after_reset(&ap->link, devmask, deadline);
> +}
> +
> +int pata_parport_softreset(struct ata_link *link, unsigned int *classes,
> + unsigned long deadline)
> +{
> + struct ata_port *ap = link->ap;
> + unsigned int slave_possible = ap->flags & ATA_FLAG_SLAVE_POSS;
> + unsigned int devmask = 0;
> + int rc;
> + u8 err;
> +
> + /* determine if device 0/1 are present */
> + if (pata_parport_devchk(ap, 0))
> + devmask |= (1 << 0);
> + if (slave_possible && pata_parport_devchk(ap, 1))
> + devmask |= (1 << 1);
> +
> + /* select device 0 again */
> + ap->ops->sff_dev_select(ap, 0);
> +
> + /* issue bus reset */
> + rc = pata_parport_bus_softreset(ap, devmask, deadline);
> + /* if link is occupied, -ENODEV too is an error */
> + if (rc && (rc != -ENODEV || sata_scr_valid(link))) {
> + ata_link_err(link, "SRST failed (errno=%d)\n", rc);
> + return rc;
> + }
> +
> + /* determine by signature whether we have ATA or ATAPI devices */
> + classes[0] = ata_sff_dev_classify(&link->device[0],
> + devmask & (1 << 0), &err);
> + if (slave_possible && err != 0x81)
> + classes[1] = ata_sff_dev_classify(&link->device[1],
> + devmask & (1 << 1), &err);
> +
> + return 0;
> +}
> +
> +u8 pata_parport_check_status(struct ata_port *ap)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> +// printk("%s\n", __FUNCTION__);
> + return pi->proto->read_regr(pi, 0, ATA_REG_STATUS);
> +}
> +
> +u8 pata_parport_check_altstatus(struct ata_port *ap)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> +// printk("%s\n", __FUNCTION__);
> + return pi->proto->read_regr(pi, 1, 6);
> +}
> +
> +void pata_parport_dev_select(struct ata_port *ap, unsigned int device)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> + u8 tmp;
> +// printk("%s\n", __FUNCTION__);
> + if (device == 0)
> + tmp = ATA_DEVICE_OBS;
> + else
> + tmp = ATA_DEVICE_OBS | ATA_DEV1;
> +
> + pi->proto->write_regr(pi, 0, ATA_REG_DEVICE, tmp);
> + ata_sff_pause(ap); /* needed; also flushes, for mmio */
> +}
> +
> +void pata_parport_tf_load(struct ata_port *ap, const struct ata_taskfile *tf)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> + unsigned int is_addr = tf->flags & ATA_TFLAG_ISADDR;
> +// printk("%s\n", __FUNCTION__);
> + if (tf->ctl != ap->last_ctl) {
> + pi->proto->write_regr(pi, 1, 6, tf->ctl);
> + ap->last_ctl = tf->ctl;
> + ata_wait_idle(ap);
> + }
> +
> + if (is_addr && (tf->flags & ATA_TFLAG_LBA48)) {
> + pi->proto->write_regr(pi, 0, ATA_REG_FEATURE, tf->hob_feature);
> + pi->proto->write_regr(pi, 0, ATA_REG_NSECT, tf->hob_nsect);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAL, tf->hob_lbal);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAM, tf->hob_lbam);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAH, tf->hob_lbah);
> + }
> +
> + if (is_addr) {
> + pi->proto->write_regr(pi, 0, ATA_REG_FEATURE, tf->feature);
> + pi->proto->write_regr(pi, 0, ATA_REG_NSECT, tf->nsect);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAL, tf->lbal);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAM, tf->lbam);
> + pi->proto->write_regr(pi, 0, ATA_REG_LBAH, tf->lbah);
> + }
> +
> + if (tf->flags & ATA_TFLAG_DEVICE)
> + pi->proto->write_regr(pi, 0, ATA_REG_DEVICE, tf->device);
> +
> + ata_wait_idle(ap);
> +}
> +
> +void pata_parport_tf_read(struct ata_port *ap, struct ata_taskfile *tf)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> +// printk("%s\n", __FUNCTION__);
> + tf->command = pi->proto->read_regr(pi, 0, ATA_REG_STATUS);
> + tf->feature = pi->proto->read_regr(pi, 0, ATA_REG_ERR);
> + tf->nsect = pi->proto->read_regr(pi, 0, ATA_REG_NSECT);
> + tf->lbal = pi->proto->read_regr(pi, 0, ATA_REG_LBAL);
> + tf->lbam = pi->proto->read_regr(pi, 0, ATA_REG_LBAM);
> + tf->lbah = pi->proto->read_regr(pi, 0, ATA_REG_LBAH);
> + tf->device = pi->proto->read_regr(pi, 0, ATA_REG_DEVICE);
> +
> + if (tf->flags & ATA_TFLAG_LBA48) {
> + pi->proto->write_regr(pi, 1, 6, tf->ctl | ATA_HOB);
> + tf->hob_feature = pi->proto->read_regr(pi, 0, ATA_REG_ERR);
> + tf->hob_nsect = pi->proto->read_regr(pi, 0, ATA_REG_NSECT);
> + tf->hob_lbal = pi->proto->read_regr(pi, 0, ATA_REG_LBAL);
> + tf->hob_lbam = pi->proto->read_regr(pi, 0, ATA_REG_LBAM);
> + tf->hob_lbah = pi->proto->read_regr(pi, 0, ATA_REG_LBAH);
> + pi->proto->write_regr(pi, 1, 6, tf->ctl);
> + ap->last_ctl = tf->ctl;
> + }
> +}
> +
> +void pata_parport_exec_command(struct ata_port *ap, const struct ata_taskfile *tf)
> +{
> + struct pi_adapter *pi = ap->host->private_data;
> +// printk("%s\n", __FUNCTION__);
> + pi->proto->write_regr(pi, 0, ATA_REG_CMD, tf->command);
> + ata_sff_pause(ap);
> +}
> +
> +unsigned int pata_parport_data_xfer(struct ata_queued_cmd *qc, unsigned char *buf,
> + unsigned int buflen, int rw)
> +{
> + struct ata_port *ap = qc->dev->link->ap;
> + struct pi_adapter *pi = ap->host->private_data;
> +// printk("%s\n", __FUNCTION__);
> + if (rw == READ)
> + pi->proto->read_block(pi, buf, buflen);
> + else
> + pi->proto->write_block(pi, buf, buflen);
> +
> + return buflen;
> +}
> +
> +void pata_parport_drain_fifo(struct ata_queued_cmd *qc)
> +{
> + int count;
> + struct ata_port *ap;
> + struct pi_adapter *pi;
> + char junk[2];
> +// printk("%s\n", __FUNCTION__);
> + /* We only need to flush incoming data when a command was running */
> + if (qc == NULL || qc->dma_dir == DMA_TO_DEVICE)
> + return;
> +
> + ap = qc->ap;
> + pi = ap->host->private_data;
> + /* Drain up to 64K of data before we give up this recovery method */
> + for (count = 0; (ap->ops->sff_check_status(ap) & ATA_DRQ)
> + && count < 65536; count += 2)
> + pi->proto->read_block(pi, junk, 2);
> +
> + if (count)
> + ata_port_dbg(ap, "drained %d bytes to clear DRQ\n", count);
> +
> +}
> +
> +void pata_parport_lost_interrupt(struct ata_port *ap)
> +{
> + u8 status;
> + struct ata_queued_cmd *qc;
> +// printk("%s\n", __FUNCTION__);
> + /* Only one outstanding command per SFF channel */
> + qc = ata_qc_from_tag(ap, ap->link.active_tag);
> + /* We cannot lose an interrupt on a non-existent or polled command */
> + if (!qc || qc->tf.flags & ATA_TFLAG_POLLING)
> + return;
> + /* See if the controller thinks it is still busy - if so the command
> + isn't a lost IRQ but is still in progress */
> + status = pata_parport_check_altstatus(ap);
> + if (status & ATA_BUSY)
> + return;
> +
> + /* There was a command running, we are no longer busy and we have
> + no interrupt. */
> + ata_port_warn(ap, "lost interrupt (Status 0x%x)\n",
> + status);
> + /* Run the host interrupt logic as if the interrupt had not been
> + lost */
> + ata_sff_port_intr(ap, qc);
> +}
> +
> +static struct ata_port_operations pata_parport_port_ops = {
> + .qc_prep = ata_noop_qc_prep,
> + .qc_issue = ata_sff_qc_issue,
> + .qc_fill_rtf = ata_sff_qc_fill_rtf,
> +
> + .freeze = ata_sff_freeze,
> + .thaw = ata_sff_thaw,
> + .prereset = ata_sff_prereset,
> + .softreset = pata_parport_softreset,
> + .postreset = ata_sff_postreset,
> + .error_handler = ata_sff_error_handler,
> + .sched_eh = ata_std_sched_eh,
> + .end_eh = ata_std_end_eh,
> +
> + .sff_dev_select = pata_parport_dev_select,
> + .sff_check_status = pata_parport_check_status,
> + .sff_check_altstatus = pata_parport_check_altstatus,
> + .sff_tf_load = pata_parport_tf_load,
> + .sff_tf_read = pata_parport_tf_read,
> + .sff_exec_command = pata_parport_exec_command,
> + .sff_data_xfer = pata_parport_data_xfer,
> + .sff_drain_fifo = pata_parport_drain_fifo,
> +
> + .lost_interrupt = pata_parport_lost_interrupt,
> +};
> +
> +static const struct ata_port_info pata_parport_port_info = {
> + .flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_PIO_POLLING,
> + .pio_mask = ATA_PIO0,
> + /* No DMA */
> + .port_ops = &pata_parport_port_ops,
> +};
> +
> +int paride_register(struct pi_protocol *pr)
> +{
> + int k;
> +
> + for (k = 0; k < MAX_PROTOS; k++)
> + if (protocols[k] && !strcmp(pr->name, protocols[k]->name)) {
> + printk("paride: %s protocol already registered\n",
> + pr->name);
> + return -1;
> + }
> + k = 0;
> + while ((k < MAX_PROTOS) && (protocols[k]))
> + k++;
> + if (k == MAX_PROTOS) {
> + printk("paride: protocol table full\n");
> + return -1;
> + }
> + protocols[k] = pr;
> + pr->index = k;
> + printk("paride: %s registered as protocol %d\n", pr->name, k);
> + return 0;
> +}
> +
> +EXPORT_SYMBOL(paride_register);
> +
> +void paride_unregister(struct pi_protocol *pr)
> +{
> + if (!pr)
> + return;
> + if (protocols[pr->index] != pr) {
> + printk("paride: %s not registered\n", pr->name);
> + return;
> + }
> + protocols[pr->index] = NULL;
> +}
> +
> +EXPORT_SYMBOL(paride_unregister);
> +
> +
> +
> +static DEFINE_SPINLOCK(pi_spinlock);
> +
> +static void pi_wake_up(void *p)
> +{
> + PIA *pi = (PIA *) p;
> + unsigned long flags;
> + void (*cont) (void) = NULL;
> +
> + spin_lock_irqsave(&pi_spinlock, flags);
> +
> + if (pi->claim_cont && !parport_claim(pi->pardev)) {
> + cont = pi->claim_cont;
> + pi->claim_cont = NULL;
> + pi->claimed = 1;
> + }
> +
> + spin_unlock_irqrestore(&pi_spinlock, flags);
> +
> + wake_up(&(pi->parq));
> +
> + if (cont)
> + cont();
> +}
> +
> +static void pi_claim(PIA * pi)
> +{
> + if (pi->claimed)
> + return;
> + pi->claimed = 1;
> + if (pi->pardev)
> + wait_event(pi->parq,
> + !parport_claim((struct pardevice *) pi->pardev));
> +}
> +
> +static void pi_unclaim(PIA * pi)
> +{
> + pi->claimed = 0;
> + if (pi->pardev)
> + parport_release((struct pardevice *) (pi->pardev));
> +}
> +
> +static void pi_unregister_parport(PIA * pi)
> +{
> + if (pi->pardev) {
> + parport_unregister_device((struct pardevice *) (pi->pardev));
> + pi->pardev = NULL;
> + }
> +}
> +
> +static int default_test_proto(PIA * pi, char *scratch, int verbose)
> +{
> + int j, k;
> + int e[2] = { 0, 0 };
> +
> + pi->proto->connect(pi);
> +
> + for (j = 0; j < 2; j++) {
> + pi->proto->write_regr(pi, 0, 6, 0xa0 + j * 0x10);
> + for (k = 0; k < 256; k++) {
> + pi->proto->write_regr(pi, 0, 2, k ^ 0xaa);
> + pi->proto->write_regr(pi, 0, 3, k ^ 0x55);
> + if (pi->proto->read_regr(pi, 0, 2) != (k ^ 0xaa))
> + e[j]++;
> + }
> + }
> + pi->proto->disconnect(pi);
> +
> + if (verbose)
> + printk("%s: %s: port 0x%x, mode %d, test=(%d,%d)\n",
> + pi->device, pi->proto->name, pi->port,
> + pi->mode, e[0], e[1]);
> +
> + return (e[0] && e[1]); /* not here if both > 0 */
> +}
> +
> +static int pi_test_proto(PIA * pi, char *scratch, int verbose)
> +{
> + int res;
> +
> + pi_claim(pi);
> + if (pi->proto->test_proto)
> + res = pi->proto->test_proto(pi, scratch, verbose);
> + else
> + res = default_test_proto(pi, scratch, verbose);
> + pi_unclaim(pi);
> +
> + return res;
> +}
> +
> +static int pi_register_parport(PIA *pi, int verbose, int unit)
> +{
> + struct parport *port;
> + struct pardev_cb par_cb;
> +
> + port = parport_find_base(pi->port);
> + if (!port)
> + return 0;
> + memset(&par_cb, 0, sizeof(par_cb));
> + par_cb.wakeup = pi_wake_up;
> + par_cb.private = (void *)pi;
> + pi->pardev = parport_register_dev_model(port, pi->device, &par_cb,
> + unit);
> + parport_put_port(port);
> + if (!pi->pardev)
> + return 0;
> +
> + init_waitqueue_head(&pi->parq);
> +
> + if (verbose)
> + printk("%s: 0x%x is %s\n", pi->device, pi->port, port->name);
> +
> + pi->parname = (char *) port->name;
> +
> + return 1;
> +}
> +
> +static int pi_probe_mode(PIA * pi, int max, char *scratch, int verbose)
> +{
> + int best, range;
> +
> + if (pi->mode != -1) {
> + if (pi->mode >= max)
> + return 0;
> + range = 3;
> + if (pi->mode >= pi->proto->epp_first)
> + range = 8;
> + if ((range == 8) && (pi->port % 8))
> + return 0;
> + pi->reserved = range;
> + return (!pi_test_proto(pi, scratch, verbose));
> + }
> + best = -1;
> + for (pi->mode = 0; pi->mode < max; pi->mode++) {
> + range = 3;
> + if (pi->mode >= pi->proto->epp_first)
> + range = 8;
> + if ((range == 8) && (pi->port % 8))
> + break;
> + pi->reserved = range;
> + if (!pi_test_proto(pi, scratch, verbose))
> + best = pi->mode;
> + }
> + pi->mode = best;
> + return (best > -1);
> +}
> +
> +
> +static int pi_probe_unit(PIA * pi, int unit, char *scratch, int verbose)
> +{
> + int max, s, e;
> +
> + s = unit;
> + e = s + 1;
> +
> + if (s == -1) {
> + s = 0;
> + e = pi->proto->max_units;
> + }
> +
> + if (!pi_register_parport(pi, verbose, s))
> + return 0;
> +
> + if (pi->proto->test_port) {
> + pi_claim(pi);
> + max = pi->proto->test_port(pi);
> + pi_unclaim(pi);
> + } else
> + max = pi->proto->max_mode;
> +
> + if (pi->proto->probe_unit) {
> + pi_claim(pi);
> + for (pi->unit = s; pi->unit < e; pi->unit++)
> + if (pi->proto->probe_unit(pi)) {
> + pi_unclaim(pi);
> + if (pi_probe_mode(pi, max, scratch, verbose))
> + return 1;
> + pi_unregister_parport(pi);
> + return 0;
> + }
> + pi_unclaim(pi);
> + pi_unregister_parport(pi);
> + return 0;
> + }
> +
> + if (!pi_probe_mode(pi, max, scratch, verbose)) {
> + pi_unregister_parport(pi);
> + return 0;
> + }
> + return 1;
> +
> +}
> +
> +int pi_init(PIA * pi, int autoprobe, int port, int mode,
> + int unit, int protocol, int delay, char *scratch,
> + int devtype, int verbose, char *device)
> +{
> + int p, k, s, e;
> + int lpts[7] = { 0x3bc, 0x378, 0x278, 0x268, 0x27c, 0x26c, 0 };
> +
> + s = protocol;
> + e = s + 1;
> +
> + if (!protocols[0])
> + request_module("paride_protocol");
> +
> + if (autoprobe) {
> + s = 0;
> + e = MAX_PROTOS;
> + } else if ((s < 0) || (s >= MAX_PROTOS) || (port <= 0) ||
> + (!protocols[s]) || (unit < 0) ||
> + (unit >= protocols[s]->max_units)) {
> + printk("%s: Invalid parameters\n", device);
> + return 0;
> + }
> +
> + for (p = s; p < e; p++) {
> + struct pi_protocol *proto = protocols[p];
> + if (!proto)
> + continue;
> + /* still racy */
> + if (!try_module_get(proto->owner))
> + continue;
> + pi->proto = proto;
> + pi->private = 0;
> + if (proto->init_proto && proto->init_proto(pi) < 0) {
> + pi->proto = NULL;
> + module_put(proto->owner);
> + continue;
> + }
> + if (delay == -1)
> + pi->delay = pi->proto->default_delay;
> + else
> + pi->delay = delay;
> + pi->devtype = devtype;
> + pi->device = device;
> +
> + pi->parname = NULL;
> + pi->pardev = NULL;
> + init_waitqueue_head(&pi->parq);
> + pi->claimed = 0;
> + pi->claim_cont = NULL;
> +
> + pi->mode = mode;
> + if (port != -1) {
> + pi->port = port;
> + if (pi_probe_unit(pi, unit, scratch, verbose))
> + break;
> + pi->port = 0;
> + } else {
> + k = 0;
> + while ((pi->port = lpts[k++]))
> + if (pi_probe_unit
> + (pi, unit, scratch, verbose))
> + break;
> + if (pi->port)
> + break;
> + }
> + if (pi->proto->release_proto)
> + pi->proto->release_proto(pi);
> + module_put(proto->owner);
> + }
> +
> + if (!pi->port) {
> + if (autoprobe)
> + printk("%s: Autoprobe failed\n", device);
> + else
> + printk("%s: Adapter not found\n", device);
> + return 0;
> + }
> +
> + if (pi->parname)
> + printk("%s: Sharing %s at 0x%x\n", pi->device,
> + pi->parname, pi->port);
> +
> + pi->proto->log_adapter(pi, scratch, verbose);
> +
> + return 1;
> +}
> +
> +static struct scsi_host_template pata_parport_sht = {
> + ATA_PIO_SHT(DRV_NAME),
> +};
> +
> +static ssize_t new_device_store(struct bus_type *bus, const char *buf, size_t count)
> +{
> + struct pi_adapter *pi;
> + int retval;
> + int autoprobe, port, mode, unit, protocol, delay;
> + int fields = 0;
> + struct device dev;
> + const struct ata_port_info *ppi[] = { &pata_parport_port_info };
> + struct ata_host *host;
> + char scratch[512];
> +
> + fields = sscanf(buf, "%x %d %d %d %d",
> + &port, &mode, &unit, &protocol, &delay);
> + if (fields < 5)
> + return -EINVAL;
> +
> + memset(&dev, 0, sizeof(dev));
> + dev.parent = bus->dev_root;
> + dev.bus = bus;
> + dev_set_name(&dev, "pata_parport%d", 0);////
> + retval = device_register(&dev);
> + if (retval) {
> + printk("register failed\n");
> + return retval;
> + }
> +
> + pi = devm_kzalloc(&dev, sizeof(struct pi_adapter), GFP_KERNEL);
> + if (!pi) {
> + //device_unregister
> + return -ENOMEM;
> + }
> +
> + if (!pi_init(pi, autoprobe, port, mode, unit, protocol, delay, scratch, PI_PD, 2, "xxx"))
> + return -ENODEV;
> +
> + printk("pi_init ok!\n");
> + pi_claim(pi);
> + pi->proto->connect(pi);
> + host = ata_host_alloc_pinfo(&dev, ppi, 1);
> + if (!host) {
> + /* pi_deinit??? */
> + return -ENOMEM;
> + }
> + host->private_data = pi;
> + printk("alloc_ok!\n");
> + if (ata_host_activate(host, 0, NULL, 0, &pata_parport_sht)) {
> + /* dealloc, pi_deinit??? */
> + return -EIO;
> + }
> +
> + return count;
> +}
> +static BUS_ATTR_WO(new_device);
> +
> +static struct bus_type pata_parport_bus = {
> + .name = "pata_parport",
> +};
> +
> +static __init int pata_parport_init(void)
> +{
> + int error;
> +
> + error = bus_register(&pata_parport_bus);
> + if (error) {
> + pr_err("failed to register pata_parport bus, error: %d\n", error);
> + return error;
> + }
> + error = bus_create_file(&pata_parport_bus, &bus_attr_new_device);
> + if (error) {
> + pr_err("unable to create sysfs file, error: %d\n", error);
> + return error;
> + }
> +
> + return 0;
> +}
> +
> +static __exit void pata_parport_exit(void)
> +{
> + bus_remove_file(&pata_parport_bus, &bus_attr_new_device);
> + bus_unregister(&pata_parport_bus);
> +}
> +
> +MODULE_AUTHOR("Ondrej Zary");
> +MODULE_DESCRIPTION("driver for parallel port ATA adapters");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("paride");
> +
> +module_init(pata_parport_init);
> +module_exit(pata_parport_exit);
> --
> Ondrej Zary
---end quoted text---
More information about the Linux-parport
mailing list