[PATCH v2] nvme: report write pointer for a full zone as zone start + zone len

[Damien Le Moal]

On 2021/11/26 19:42, Niklas Cassel wrote:
> From: Niklas Cassel <niklas.cassel at wdc.com>
> 
> The write pointer in NVMe ZNS is invalid for a zone in zone state full.
> The same also holds true for ZAC/ZBC.
> 
> The current behavior for NVMe is to simply propagate the wp reported by
> the drive, even for full zones. Since the wp is invalid for a full zone,
> the wp reported by the drive may be any value.
> 
> The way that the sd_zbc driver handles a full zone is to always report
> the wp as zone start + zone len, regardless of what the drive reported.
> null_blk also follows this convention.
> 
> Do the same for NVMe, so that a BLKREPORTZONE ioctl reports the write
> pointer for a full zone in a consistent way, regardless of the interface
> of the underlying zoned block device.
> 
> blkzone report before patch:
> start: 0x000040000, len 0x040000, cap 0x03e000, wptr 0xfffffffffffbfff8
> reset:0 non-seq:0, zcond:14(fu) [type: 2(SEQ_WRITE_REQUIRED)]
> 
> blkzone report after patch:
> start: 0x000040000, len 0x040000, cap 0x03e000, wptr 0x040000 reset:0
> non-seq:0, zcond:14(fu) [type: 2(SEQ_WRITE_REQUIRED)]
> 
> Signed-off-by: Niklas Cassel <niklas.cassel at wdc.com>
> ---
> Changes since v1:
> - Minor commit message rewording.
> - Use if/else instead of setting wp unconditionally and then
>   conditionally updating it.
> 
>  drivers/nvme/host/zns.c | 5 ++++-
>  1 file changed, 4 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/nvme/host/zns.c b/drivers/nvme/host/zns.c
> index bfc259e0d7b8..9f81beb4df4e 100644
> --- a/drivers/nvme/host/zns.c
> +++ b/drivers/nvme/host/zns.c
> @@ -166,7 +166,10 @@ static int nvme_zone_parse_entry(struct nvme_ns *ns,
>  	zone.len = ns->zsze;
>  	zone.capacity = nvme_lba_to_sect(ns, le64_to_cpu(entry->zcap));
>  	zone.start = nvme_lba_to_sect(ns, le64_to_cpu(entry->zslba));
> -	zone.wp = nvme_lba_to_sect(ns, le64_to_cpu(entry->wp));
> +	if (zone.cond == BLK_ZONE_COND_FULL)
> +		zone.wp = zone.start + zone.len;
> +	else
> +		zone.wp = nvme_lba_to_sect(ns, le64_to_cpu(entry->wp));
>  
>  	return cb(&zone, idx, data);
>  }
> 

Looks good.

Reviewed-by: Damien Le Moal <damien.lemoal at opensource.wdc.com>

Note: read-only zones also have an undefined wp. So I wonder if we should not
set the wp similarly to full zones, to match the fact that we cannot write to
these zones. Same for offline zones, but these are tricky since they cannot be
read either, meaning that wp should be set to the zone start for that case...


-- 
Damien Le Moal
Western Digital Research