[PATCH 3/3] nvmetcli: remove README file

[Jay Freyensee]

Contents of README have been moved and updated into the
manpage/html solution.

Signed-off-by: Jay Freyensee <james.p.freyensee at intel.com>
---
 README | 173 -----------------------------------------------------------------
 1 file changed, 173 deletions(-)
 delete mode 100644 README

diff --git a/README b/README
deleted file mode 100644
index 4c44b39..0000000
--- a/README
+++ /dev/null
@@ -1,173 +0,0 @@
-nvmetcli
-========
-This contains the NVMe target admin tool "nvmetcli".  It can either be
-used interactively by invoking it without arguments, or it can be used
-to save, restore or clear the current NVMe target configuration.
-
-Installation
-------------
-Please install the configshell-fb package from
-https://github.com/agrover/configshell-fb first.
-
-nvmetcli can be run directly from the source directory or installed
-using setup.py.
-
-Common Package Dependencies and Problems
------------------------------------------
-nvmetcli uses the 'python-six' and 'pyparsing' packages
-(running nvmetcli without these packages may produce
-hard-to-decipher errors).
-
-Walk-Through Example Usage
----------------------------
-Make sure to run nvmetcli as root, the nvmet module is loaded,
-your devices are loaded, and configfs is mounted on /sys/kernel/config
-using:
-
-	mount -t configs none /sys/kernel/config
-
-To get started with the interactive mode and the nvmetcli command prompt,
-type (in root):
-
-./nvmetcli
-...>
-
-The following walks through an example using interactive mode.
-
-# 
-# Create a subsystem.  If you do not specify a name a NQN will be generated,
-# which is probably the best choice, we we don't do it here as the name
-# would be random
-#
-
-> cd /subsystems
-...> create testnqn
-
-#
-# Add access for a specific NVMe Host by it's NQN:
-#
-
-...> cd /hosts
-...> create hostnqn
-...> cd /subsystems/testnqn/allowed_hosts/
-...> create hostnqn
-
-#
-# remove access of a subsystem by deleting the Host NQN
-#
-
-...> cd /subsystems/testnqn/allowed_hosts/
-...> delete hostnqn
-
-#
-# Alternatively this allows any host to connect to the subsystsem.  Only
-# use this in tightly controller environments:
-#
-
-...> cd /subsystems/testnqn/
-...> set attr allow_any_host=1
-
-#
-# Create a new namespace.  If you do not specify a namespace ID the fist
-# unused one will be used.
-#
-
-...> cd /subsystems/testnqn/namespaces
-...> create 1
-...> cd 1
-...> set device path=/dev/nvme0n1
-...> enable
-
-# Note that in the above setup the 'device_nguid' attribute
-# does not have to be set for correct NVMe Target functionality.
-
-#
-# Create a port through which access is allowed, and enable access to
-# a subsystem through it.
-#
-# This creates a trivial loopback port that can be used with nvme-loop on
-# the same machine:
-#
-
-...> cd /ports/
-...> create 1
-...> cd 1/
-...> set addr trtype=loop
-...> cd subsystems/
-...> create testnqn
-
-#
-# Or create a RDMA (IB, RoCE, iWarp) port using IPv4 addressing, 4420 is the
-# IANA assigned port for NVMe over Fabrics using RDMA:
-#
-
-...> cd /ports/
-...> create 2
-...> cd 2/
-...> set addr trtype=rdma
-...> set addr adrfam=ipv4
-...> set addr traddr=192.168.6.68
-...> set addr trsvcid=4420
-...> cd subsystems/
-...> create testnqn
-
-Discovery
-----------
-Each NVMe Target has a discovery controller mechanism that an NVMe
-Host can use to determine the NVM subsystems it has access too.
-nvmetcli can be used to add a new record to the discovery controller
-upon each new subsystem entry and port entry that the newly
-created subsystem entry binds too (see the '/port/' and
-'/subystem/' nvmetcli walk-through earlier in this README).  Each NVMe
-Host only gets to see the discovery entries defined in
-/subsystems/[NQN NAME]/allowed_hosts and the IP port it is connected
-to the NVMe Target.
-
-A Host can retrieve these discovery logs via the nvme-cli tool
-(https://github.com/linux-nvme/nvme-cli).
-
-Referrals
----------
-TBD
-
-Saving and restoring the configuration
---------------------------------------
-The saveconfig command in the interactive
-nvmetcli mode saves the current configuration.  For example,
-
-./nvmetcli
-...> saveconfig test.json
-
-You can also invoke a 'save' command, as well as a 'restore'
-and 'clear' command on the Linux command line.  For example,
-
-(to load an NVMe Target configuration):
-  ./nvmetcli restore test.json
-
-(to clear a current NVMe Target configuration):
-  ./nvmetcli clear test.json
-
-Without an additional file name these operate on /etc/nvmet/config.json.
-
-Example NVMe Target .json files
---------------------------------------
-To load the loop + explicit host version above do the following:
-
-  ./nvmetcli restore loop.json
-
-Or to load the rdma + no host authentication version do the following
-after you've ensured that the IP address in rdma.json fits your setup:
-
-  ./nvmetcli restore rdma.json
-
-These files can also be edited directly using your favorite editor.
-
-Testing
--------
-nvmetcli comes with a testsuite that tests itself and the kernel configfs
-interface for the NVMe target.  To run it make sure you have nose2 and
-the coverage plugin for it installed and simple run 'make test'.
-
-Development
------------------
-Please send to linux-nvme at lists.infradead.org for review and acceptance.
-- 
2.7.4