[RESEND PATCH v2 29/53] mtd: nand: denali: remove Toshiba and Hynix specific fixup code

Masahiro Yamada yamada.masahiro at socionext.com
Wed Mar 22 17:17:38 PDT 2017


The Denali IP can automatically detect device parameters such as
page size, oob size, device width, etc. and this driver currently
relies on it.  However, this hardware function is problematic.

[1] Due to a hardware bug, various misdetected cases are known.
    That is why get_toshiba_nand_para() and get_hynix_nand_para()
    exist to fix-up the misdetected parameters.  It is not realistic
    to add a new NAND device to the *black list* every time we are
    hit by a misdetected case.  We would never be able to guarantee
    that all cases are covered.

[2] Because this feature is unreliable, it is disabled on some
    platforms.

The nand_scan_ident() detects device parameters in a more tested
way.  The hardware should not set the device parameter registers in
a different, unreliable way.  Instead, set the parameters from the
nand_scan_ident() back to the registers.

Signed-off-by: Masahiro Yamada <yamada.masahiro at socionext.com>
---

Changes in v2: None

 drivers/mtd/nand/denali.c | 40 ++++++----------------------------------
 1 file changed, 6 insertions(+), 34 deletions(-)

diff --git a/drivers/mtd/nand/denali.c b/drivers/mtd/nand/denali.c
index 70e9f06..fba1908 100644
--- a/drivers/mtd/nand/denali.c
+++ b/drivers/mtd/nand/denali.c
@@ -338,36 +338,6 @@ static void get_samsung_nand_para(struct denali_nand_info *denali,
 	}
 }
 
-static void get_toshiba_nand_para(struct denali_nand_info *denali)
-{
-	/*
-	 * Workaround to fix a controller bug which reports a wrong
-	 * spare area size for some kind of Toshiba NAND device
-	 */
-	if ((ioread32(denali->flash_reg + DEVICE_MAIN_AREA_SIZE) == 4096) &&
-		(ioread32(denali->flash_reg + DEVICE_SPARE_AREA_SIZE) == 64))
-		iowrite32(216, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
-}
-
-static void get_hynix_nand_para(struct denali_nand_info *denali,
-							uint8_t device_id)
-{
-	switch (device_id) {
-	case 0xD5: /* Hynix H27UAG8T2A, H27UBG8U5A or H27UCG8VFA */
-	case 0xD7: /* Hynix H27UDG8VEM, H27UCG8UDM or H27UCG8V5A */
-		iowrite32(128, denali->flash_reg + PAGES_PER_BLOCK);
-		iowrite32(4096, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
-		iowrite32(224, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
-		iowrite32(0, denali->flash_reg + DEVICE_WIDTH);
-		break;
-	default:
-		dev_warn(denali->dev,
-			 "Unknown Hynix NAND (Device ID: 0x%x).\n"
-			 "Will use default parameter values instead.\n",
-			 device_id);
-	}
-}
-
 /*
  * determines how many NAND chips are connected to the controller. Note for
  * Intel CE4100 devices we don't support more than one device.
@@ -454,10 +424,6 @@ static uint16_t denali_nand_timing_set(struct denali_nand_info *denali)
 			return FAIL;
 	} else if (maf_id == 0xEC) { /* Samsung NAND */
 		get_samsung_nand_para(denali, device_id);
-	} else if (maf_id == 0x98) { /* Toshiba NAND */
-		get_toshiba_nand_para(denali);
-	} else if (maf_id == 0xAD) { /* Hynix NAND */
-		get_hynix_nand_para(denali, device_id);
 	}
 
 	dev_info(denali->dev,
@@ -1649,6 +1615,12 @@ int denali_init(struct denali_nand_info *denali)
 						chip->ecc.strength);
 
 	iowrite32(chip->ecc.strength, denali->flash_reg + ECC_CORRECTION);
+	iowrite32(mtd->erasesize / mtd->writesize,
+		  denali->flash_reg + PAGES_PER_BLOCK);
+	iowrite32(denali->nand.options & NAND_BUSWIDTH_16 ? 1 : 0,
+		  denali->flash_reg + DEVICE_WIDTH);
+	iowrite32(mtd->writesize, denali->flash_reg + DEVICE_MAIN_AREA_SIZE);
+	iowrite32(mtd->oobsize, denali->flash_reg + DEVICE_SPARE_AREA_SIZE);
 
 	iowrite32(chip->ecc.size, denali->flash_reg + CFG_DATA_BLOCK_SIZE);
 	iowrite32(chip->ecc.size, denali->flash_reg + CFG_LAST_DATA_BLOCK_SIZE);
-- 
2.7.4




More information about the linux-mtd mailing list