[PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection

Bean Huo 霍斌斌 (beanhuo) beanhuo at micron.com
Sun Mar 20 19:55:56 PDT 2016


Hi, Yunhai
You mean that EVCR.bit7 cannot clear(enable quad mode) if not write SR.bit7 to 0?
They don't have any connection each other.

> -----Original Message-----
> From: Yunhui Cui [mailto:yunhui.cui at nxp.com]
> Sent: Friday, March 18, 2016 6:09 PM
> To: Bean Huo 霍斌斌 (beanhuo); Yunhui Cui
> Cc: linux-mtd at lists.infradead.org; dwmw2 at infradead.org;
> computersforpeace at gmail.com; han.xu at freescale.com;
> linux-kernel at vger.kernel.org; linux-mtd at lists.infradead.org;
> linux-arm-kernel at lists.infradead.org; Yao Yuan
> Subject: RE: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection
> 
> Hi Bean,
> 
> Thanks for your suggestions very much.
> Yes, the flash N25Q128A status register write enable/disable bit is disable in
> initial state.
> But, This patch aims to clear status registerV bit[7](write enable/disable bit) to
> 0, which enables the bit.
> Frankly speaking, I also don't want to add this patch.
> The reason for this is that clear status register bit[7] to 0 is a must to set quad
> mode to Enhanced Volatile Configuration Register using command
> SPINOR_OP_WD_EVCR. Otherwise it will output "Micron EVCR Quad bit not
> clear" in spi-nor.c I looked up the datasheet, but I really don't find out any
> connection between status register bit[7](write enable/disable bit) equals 0
> and seting quad mode to Enhanced Volatile Configuration Register.
> 
> Just as I want to send the issue to Micron team , could you give me some
> solutions ?
> 
> 
> Thanks
> Yunhui
> 
> -----Original Message-----
> From: Bean Huo 霍斌斌 (beanhuo) [mailto:beanhuo at micron.com]
> Sent: Thursday, March 03, 2016 9:39 PM
> To: Yunhui Cui
> Cc: linux-mtd at lists.infradead.org; dwmw2 at infradead.org;
> computersforpeace at gmail.com; han.xu at freescale.com;
> linux-kernel at vger.kernel.org; linux-mtd at lists.infradead.org;
> linux-arm-kernel at lists.infradead.org; Yao Yuan; Yunhui Cui
> Subject: Re: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW protection
> 
> > From: Yunhui Cui <B56489 at freescale.com>
> > To: <dwmw2 at infradead.org>, <computersforpeace at gmail.com>,
> > 	<han.xu at freescale.com>
> > Cc: <linux-kernel at vger.kernel.org>, <linux-mtd at lists.infradead.org>,
> > 	<linux-arm-kernel at lists.infradead.org>, <yao.yuan at nxp.com>, Yunhui
> > Cui
> > 	<yunhui.cui at nxp.com>
> > Subject: [PATCH v3 4/4] mtd: spi-nor: Disable Micron flash HW
> > 	protection
> > Message-ID:
> <1456988044-37061-4-git-send-email-B56489 at freescale.com>
> > Content-Type: text/plain
> >
> > From: Yunhui Cui <yunhui.cui at nxp.com>
> >
> > For Micron family ,The status register write enable/disable bit,
> > provides hardware data protection for the device.
> > When the enable/disable bit is set to 1, the status register
> > nonvolatile bits become read-only and the WRITE STATUS REGISTER
> > operation will not execute.
> >
> > Signed-off-by: Yunhui Cui <yunhui.cui at nxp.com>
> > ---
> >  drivers/mtd/spi-nor/spi-nor.c | 9 +++++++++
> >  1 file changed, 9 insertions(+)
> >
> > diff --git a/drivers/mtd/spi-nor/spi-nor.c
> > b/drivers/mtd/spi-nor/spi-nor.c index ed0c19c..917f814 100644
> > --- a/drivers/mtd/spi-nor/spi-nor.c
> > +++ b/drivers/mtd/spi-nor/spi-nor.c
> > @@ -39,6 +39,7 @@
> >
> >  #define SPI_NOR_MAX_ID_LEN	6
> >  #define SPI_NOR_MAX_ADDR_WIDTH	4
> > +#define SPI_NOR_MICRON_WRITE_ENABLE	0x7f
> >
> >  struct flash_info {
> >  	char		*name;
> > @@ -1238,6 +1239,14 @@ int spi_nor_scan(struct spi_nor *nor, const
> > char *name, enum read_mode mode)
> >  		write_sr(nor, 0);
> >  	}
> >
> > +	if (JEDEC_MFR(info) == SNOR_MFR_MICRON) {
> > +		ret = read_sr(nor);
> > +		ret &= SPI_NOR_MICRON_WRITE_ENABLE;
> > +
> For Micron the status register write enable/disable bit, its default/factory
> value is disable.
> Can here first check ,then program?
> > +		write_enable(nor);
> > +		write_sr(nor, ret);
> > +	}
> > +
> >  	if (!mtd->name)
> >  		mtd->name = dev_name(dev);
> >  	mtd->priv = nor;


More information about the linux-mtd mailing list