[PATCH 2/2] mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller.

[vikas]

Hi,

On 08/25/2015 11:19 PM, Marek Vasut wrote:
> On Wednesday, August 26, 2015 at 12:09:50 AM, vikas wrote:
>> Hi,
>>
>> On 08/21/2015 02:20 AM, Marek Vasut wrote:
>>> From: Graham Moore <grmoore at opensource.altera.com>
>>>
>>> Add support for the Cadence QSPI controller. This controller is
>>> present in the Altera SoCFPGA SoCs and this driver has been tested
>>> on the Cyclone V SoC.
>>>
>>> Signed-off-by: Graham Moore <grmoore at opensource.altera.com>
>>> Signed-off-by: Marek Vasut <marex at denx.de>
>>> Cc: Alan Tull <atull at opensource.altera.com>
>>> Cc: Brian Norris <computersforpeace at gmail.com>
>>> Cc: David Woodhouse <dwmw2 at infradead.org>
>>> Cc: Dinh Nguyen <dinguyen at opensource.altera.com>
>>> Cc: Graham Moore <grmoore at opensource.altera.com>
>>> Cc: Vikas MANOCHA <vikas.manocha at st.com>
>>> Cc: Yves Vandervennet <yvanderv at opensource.altera.com>
>>> Cc: devicetree at vger.kernel.org
>>> ---
>>>
>>>  drivers/mtd/spi-nor/Kconfig           |   11 +
>>>  drivers/mtd/spi-nor/Makefile          |    1 +
>>>  drivers/mtd/spi-nor/cadence-quadspi.c | 1260
>>>  +++++++++++++++++++++++++++++++++ 3 files changed, 1272 insertions(+)
>>>  create mode 100644 drivers/mtd/spi-nor/cadence-quadspi.c
>>>
>>> V2: use NULL instead of modalias in spi_nor_scan call
>>> V3: Use existing property is-decoded-cs instead of creating duplicate.
>>> V4: Support Micron quad mode by snooping command stream for EVCR command
>>>
>>>     and subsequently configuring Cadence controller for quad mode.
>>>
>>> V5: Clean up sparse and smatch complaints.  Remove snooping of Micron
>>>
>>>     quad mode.  Add comment on XIP mode bit and dummy clock cycles.  Set
>>>     up SRAM partition at 1:1 during init.
>>>
>>> V6: Remove dts patch that was included by mistake.  Incorporate Vikas's
>>>
>>>     comments regarding fifo width, SRAM partition setting, and trigger
>>>     address.  Trigger address was added as an unsigned int, as it is not
>>>     an IO resource per se, and does not need to be mapped. Also add
>>>     Marek Vasut's workaround for picking up OF properties on subnodes.
>>>
>>> V7: - Perform coding-style cleanup and type fixes. Remove ugly QSPI_*()
>>>
>>>       macros and replace them with functions. Get rid of unused
>>>       variables.
>>>     
>>>     - Implement support for nor->set_protocol() to handle Quad-command,
>>>     
>>>       this patch now depends on the following patch:
>>>       mtd: spi-nor: notify (Q)SPI controller about protocol change
>>>     
>>>     - Replace that cqspi_fifo_read() disaster with plain old readsl()
>>>     
>>>       and cqspi_fifo_write() tentacle horror with pretty writesl().
>>>     
>>>     - Remove CQSPI_SUPPORT_XIP_CHIPS, which is broken.
>>>     - Get rid of cqspi_find_chipselect() mess, instead just place the
>>>     
>>>       struct cqspi_st and chipselect number into struct cqspi_flash_pdata
>>>       and set nor->priv to the struct cqspi_flash_pdata of that
>>>       particular chip.
>>>     
>>>     - Replace the odd math in calculate_ticks_for_ns() with
>>>     DIV_ROUND_UP(). - Make variables const where applicable.
>>>
>>> V8: - Implement a function to wait for bit being set/unset for a given
>>>
>>>       period of time and use it to replace the ad-hoc bits of code.
>>>     
>>>     - Configure the write underflow watermark to be 1/8 if FIFO size.
>>>     - Extract out the SPI NOR flash probing code into separate function
>>>     
>>>       to clearly mark what will soon be considered a boilerplate code.
>>>     
>>>     - Repair the handling of mode bits, which caused instability in V7.
>>>     - Clean up the interrupt handling
>>>     - Fix Kconfig help text and make the patch depend on OF and
>>>     COMPILE_TEST.
>>>
>>> diff --git a/drivers/mtd/spi-nor/Kconfig b/drivers/mtd/spi-nor/Kconfig
>>> index 89bf4c1..ed253a2 100644
>>> --- a/drivers/mtd/spi-nor/Kconfig
>>> +++ b/drivers/mtd/spi-nor/Kconfig
>>> @@ -40,4 +40,15 @@ config SPI_NXP_SPIFI
>>>
>>>           Flash. Enable this option if you have a device with a SPIFI
>>>           controller and want to access the Flash as a mtd device.
>>>
>>> +config SPI_CADENCE_QUADSPI
>>> +       tristate "Cadence Quad SPI controller"
>>> +       depends on OF && COMPILE_TEST
>>> +       help
>>> +         Enable support for the Cadence Quad SPI Flash controller.
>>> +
>>> +         Cadence QSPI is a specialized controller for connecting an SPI
>>> +         Flash over 1/2/4-bit wide bus. Enable this option if you have a
>>> +         device with a Cadence QSPI controller and want to access the
>>> +         Flash as an MTD device.
>>> +
>>
>> the patch failed to apply, please rebase it to master.
> 
> it's based on -next, I'm sure you can fix trivial conflicts yourself if you
> need to apply it elsewhere. Do you have any other review comments ?

Always rebase the patch on master.
I will be reviewing the patchset this week but on a quick look it seems many review comments of v7 are not there.

Cheers,
Vikas

> .
>