[PATCH v3 3/5] mtd: ofpart: update devicetree binding specification

Michal Suchanek hramrach at gmail.com
Tue Aug 18 08:34:08 PDT 2015


To avoid conflict with other drivers using subnodes of the mtd device
create only one ofpart-specific node rather than any number of
arbitrary partition subnodes.

Signed-off-by: Michal Suchanek <hramrach at gmail.com>
---
v3:

 - rename DT node ofpart -> partitions
---
 .../devicetree/bindings/mtd/partition.txt          | 68 +++++++++++++---------
 1 file changed, 40 insertions(+), 28 deletions(-)

diff --git a/Documentation/devicetree/bindings/mtd/partition.txt b/Documentation/devicetree/bindings/mtd/partition.txt
index 8e5557d..8c2aff7 100644
--- a/Documentation/devicetree/bindings/mtd/partition.txt
+++ b/Documentation/devicetree/bindings/mtd/partition.txt
@@ -4,10 +4,16 @@ Partitions can be represented by sub-nodes of an mtd device. This can be used
 on platforms which have strong conventions about which portions of a flash are
 used for what purposes, but which don't use an on-flash partition table such
 as RedBoot.
+
+The partition table should be partitions subnode of the mtd node. Partitions are
+defined in subnodes of the partitions node.
+
+For backwards compatibility partitions as direct subnodes of the mtd device are
+supported. This use is discouraged.
 NOTE: if the sub-node has a compatible string, then it is not a partition.
 
-#address-cells & #size-cells must both be present in the mtd device. There are
-two valid values for both:
+#address-cells & #size-cells must both be present in the partitions subnode of the
+mtd device. There are two valid values for both:
 <1>: for partitions that require a single 32-bit cell to represent their
      size/address (aka the value is below 4 GiB)
 <2>: for partitions that require two 32-bit cells to represent their
@@ -28,44 +34,50 @@ Examples:
 
 
 flash at 0 {
-	#address-cells = <1>;
-	#size-cells = <1>;
+	partitions {
+		#address-cells = <1>;
+		#size-cells = <1>;
 
-	partition at 0 {
-		label = "u-boot";
-		reg = <0x0000000 0x100000>;
-		read-only;
-	};
+		partition at 0 {
+			label = "u-boot";
+			reg = <0x0000000 0x100000>;
+			read-only;
+		};
 
-	uimage at 100000 {
-		reg = <0x0100000 0x200000>;
+		uimage at 100000 {
+			reg = <0x0100000 0x200000>;
+		};
 	};
 };
 
 flash at 1 {
-	#address-cells = <1>;
-	#size-cells = <2>;
+	partitions {
+		#address-cells = <1>;
+		#size-cells = <2>;
 
-	/* a 4 GiB partition */
-	partition at 0 {
-		label = "filesystem";
-		reg = <0x00000000 0x1 0x00000000>;
+		/* a 4 GiB partition */
+		partition at 0 {
+			label = "filesystem";
+			reg = <0x00000000 0x1 0x00000000>;
+		};
 	};
 };
 
 flash at 2 {
-	#address-cells = <2>;
-	#size-cells = <2>;
+	partitions {
+		#address-cells = <2>;
+		#size-cells = <2>;
 
-	/* an 8 GiB partition */
-	partition at 0 {
-		label = "filesystem #1";
-		reg = <0x0 0x00000000 0x2 0x00000000>;
-	};
+		/* an 8 GiB partition */
+		partition at 0 {
+			label = "filesystem #1";
+			reg = <0x0 0x00000000 0x2 0x00000000>;
+		};
 
-	/* a 4 GiB partition */
-	partition at 200000000 {
-		label = "filesystem #2";
-		reg = <0x2 0x00000000 0x1 0x00000000>;
+		/* a 4 GiB partition */
+		partition at 200000000 {
+			label = "filesystem #2";
+			reg = <0x2 0x00000000 0x1 0x00000000>;
+		};
 	};
 };
-- 
2.1.4




More information about the linux-mtd mailing list