mxc_nand.c on mach-imx/imx53

Roland Stigge stigge at antcom.de
Wed Aug 29 11:20:17 EDT 2012


Hi Sascha,

On 08/29/2012 09:41 AM, Sascha Hauer wrote:
> On Thu, Aug 23, 2012 at 11:30:54AM +0200, Roland Stigge wrote:
>> Hi,
>>
>> I'd like to know about the current state of mxc_nand.c on imx53, because
>> I got an error on probe() because the clock that mxc_nand is requesting
>> is "nfc" but imx53 only defines the clock "mxc_nand".
> 
> The driver generally works on i.MX53, only some pieces are missing. I
> just resent the corresponding series and put you on Cc.

Good - thank you for the patches, didn't know about them.

Now, my flash is detected:

NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron NAND 512MiB
3,3V 8-bit), page size: 4096, OOB size: 128

However, when I read a partition, kernel (mxc_nand_correct_data_v2_v3())
says:

...
UnCorrectable RS-ECC Error
UnCorrectable RS-ECC Error
UnCorrectable RS-ECC Error
UnCorrectable RS-ECC Error
UnCorrectable RS-ECC Error
UnCorrectable RS-ECC Error
UnCorrectable RS-ECC Error
...

I'm using the following dt (on an Emtrion DIMM-MX53 board):

                        nand at 63fdb000 {
                                status = "okay";
                                #address-cells = <1>;
                                #size-cells = <1>;
                                nand-bus-width = <8>;
                                nand-ecc-mode = "hw";

                                mtd0 at 00000000 {
                                        label = "bootstrap";
                                        reg = <0x00000000 0x80000>;
                                        read-only;
                                };
                                mtd1 at 00080000 {
                                        label = "uboot";
                                        reg = <0x00080000 0x80000>;
                                        read-only;
                                };
                                mtd2 at 00100000 {
                                        label = "NVRAM";
                                        reg = <0x00100000 0x100000>;
                                };
                                mtd3 at 00200000 {
                                        label = "bootlogo";
                                        reg = <0x00200000 0x80000>;
                                };
                                mtd4 at 00280000 {
                                        label = "linux";
                                        reg = <0x00280000 0x400000>;
                                };
                                mtd5 at 00680000 {
                                        label = "rootfs";
                                        reg = <0x00680000 0x8000000>;
                                };
                                mtd6 at 08680000 {
                                        label = "appfs";
                                        reg = <0x08680000 0x17980000>;
                                };
                        };

NAND info from u-boot:

NAND:  512 MiB
Manufacturer      : Micron (0x2c)
Device Code       : 0xdc
Cell Technology   : SLC
Chip Size         : 512 MiB
Pages per Block   : 64
Page Geometry     : 4096+218
ECC Strength      : 8 bits
ECC Size          : 512 B
Data Setup Time   : 20 ns
Data Hold Time    : 10 ns
Address Setup Time: 10 ns
GPMI Sample Delay : 6 ns
tREA              : Unknown
tRLOH             : Unknown
tRHOH             : Unknown
Description       : MT29F4G08ABAEA

I guess I hit a documented open issue:

/* v3.2b: i.MX53 */
static const struct mxc_nand_devtype_data imx53_nand_devtype_data = {
        .preset = preset_v3,
        .send_cmd = send_cmd_v3,
        .send_addr = send_addr_v3,
        .send_page = send_page_v3,
        .send_read_id = send_read_id_v3,
        .get_dev_status = get_dev_status_v3,
        .check_int = check_int_v3,
        .irq_control = irq_control_v3,
        .get_ecc_status = get_ecc_status_v3,
        .ecclayout_512 = &nandv2_hw_eccoob_smallpage,
        .ecclayout_2k = &nandv2_hw_eccoob_largepage,
        .ecclayout_4k = &nandv2_hw_eccoob_smallpage, /* XXX: needs fix */

Using  ".ecclayout_4k = &nandv2_hw_eccoob_4k" also doesn't work. So is
there any hint how I can proceed from here? Any plans or hint regarding
the "XXX"?

Thanks in advance,

Roland



More information about the linux-mtd mailing list