[PATCH RFC net-next v2 06/10] net: dsa: mt7530: only indicate linkmodes that can be supported

Russell King (Oracle) rmk+kernel at armlinux.org.uk
Wed Feb 23 03:34:43 PST 2022


Now that mt7530 is not using the basex helper, it becomes unnecessary to
indicate support for both 1000baseX and 2500baseX when one of the 803.3z
PHY interface modes is being selected. Ensure that the driver indicates
only those linkmodes that can actually be supported by the PHY interface
mode.

Signed-off-by: Russell King (Oracle) <rmk+kernel at armlinux.org.uk>
---
 drivers/net/dsa/mt7530.c | 14 +++++++++-----
 drivers/net/dsa/mt7530.h |  1 +
 2 files changed, 10 insertions(+), 5 deletions(-)

diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index 25c3c54f1380..db1d13718ff1 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -2517,13 +2517,14 @@ static int mt7531_rgmii_setup(struct mt7530_priv *priv, u32 port,
 }
 
 static void mt7531_sgmii_validate(struct mt7530_priv *priv, int port,
+				  phy_interface_t interface,
 				  unsigned long *supported)
 {
 	/* Port5 supports ethier RGMII or SGMII.
 	 * Port6 supports SGMII only.
 	 */
-	if (port == 6 ||
-	    (port == 5 && !mt7531_is_rgmii_port(priv, port))) {
+	if ((port == 5 || port == 6) &&
+	    interface == PHY_INTERFACE_MODE_2500BASEX) {
 		phylink_set(supported, 2500baseX_Full);
 		phylink_set(supported, 2500baseT_Full);
 	}
@@ -2898,16 +2899,18 @@ static void mt753x_phylink_get_caps(struct dsa_switch *ds, int port,
 
 static void
 mt7530_mac_port_validate(struct dsa_switch *ds, int port,
+			 phy_interface_t interface,
 			 unsigned long *supported)
 {
 }
 
 static void mt7531_mac_port_validate(struct dsa_switch *ds, int port,
+				     phy_interface_t interface,
 				     unsigned long *supported)
 {
 	struct mt7530_priv *priv = ds->priv;
 
-	mt7531_sgmii_validate(priv, port, supported);
+	mt7531_sgmii_validate(priv, port, interface, supported);
 }
 
 static void
@@ -2930,12 +2933,13 @@ mt753x_phylink_validate(struct dsa_switch *ds, int port,
 	}
 
 	/* This switch only supports 1G full-duplex. */
-	if (state->interface != PHY_INTERFACE_MODE_MII) {
+	if (state->interface != PHY_INTERFACE_MODE_MII &&
+	    state->interface != PHY_INTERFACE_MODE_2500BASEX)
 		phylink_set(mask, 1000baseT_Full);
 		phylink_set(mask, 1000baseX_Full);
 	}
 
-	priv->info->mac_port_validate(ds, port, mask);
+	priv->info->mac_port_validate(ds, port, state->interface, mask);
 
 	phylink_set(mask, Pause);
 	phylink_set(mask, Asym_Pause);
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index cbebbcc76509..73cfd29fbb17 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -772,6 +772,7 @@ struct mt753x_info {
 	void (*mac_port_get_caps)(struct dsa_switch *ds, int port,
 				  struct phylink_config *config);
 	void (*mac_port_validate)(struct dsa_switch *ds, int port,
+				  phy_interface_t interface,
 				  unsigned long *supported);
 	int (*mac_port_get_state)(struct dsa_switch *ds, int port,
 				  struct phylink_link_state *state);
-- 
2.30.2




More information about the Linux-mediatek mailing list