[PATCH v2 1/1] arm64: dts: freescale: add pixpaper display overlay for i.MX93 FRDM

[Frank Li]

On Wed, Jan 28, 2026 at 01:05:49PM +0800, Wig Cheng wrote:

"Add device tree overlay to support the MayQueen PixPaper e-paper display
on the NXP i.MX93 FRDM board. The display is connected via LPSPI3
interface and uses GPIO pins for reset, busy and DC control.

The overlay configures:
    - LPSPI3 pinmux for SPI communication (MOSI, MISO, CLK, CE0)
    - PixPaper display device with proper GPIO assignments
    - SPI frequency set to 5MHz for stable operation
"

Sorry, My means just replace 3rd paragraph. First 2 paragraph is good.

Frank

> Enable Open-EP Community pixpaper-213-c support on NXP i.MX93.
>
> Signed-off-by: Wig Cheng <onlywig at gmail.com>
> ---
>  arch/arm64/boot/dts/freescale/Makefile        |  4 ++
>  .../freescale/imx93-11x11-frdm-pixpaper.dtso  | 51 +++++++++++++++++++
>  2 files changed, 55 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/freescale/imx93-11x11-frdm-pixpaper.dtso
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index ce8f937c2315..c2727f8061e2 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -398,6 +398,10 @@ dtb-$(CONFIG_ARCH_MXC) += imx93-9x9-qsb-i3c.dtb
>
>  dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-frdm.dtb
> +
> +imx93-11x11-frdm-pixpaper-dtbs += imx93-11x11-frdm.dtb imx93-11x11-frdm-pixpaper.dtbo
> +dtb-$(CONFIG_ARCH_MXC) += imx93-11x11-frdm-pixpaper.dtb
> +
>  dtb-$(CONFIG_ARCH_MXC) += imx93-14x14-evk.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx93-kontron-bl-osm-s.dtb
>  dtb-$(CONFIG_ARCH_MXC) += imx93-phyboard-nash.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx93-11x11-frdm-pixpaper.dtso b/arch/arm64/boot/dts/freescale/imx93-11x11-frdm-pixpaper.dtso
> new file mode 100644
> index 000000000000..1111503b08af
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx93-11x11-frdm-pixpaper.dtso
> @@ -0,0 +1,51 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree Overlay for Mayqueen (Open-EP Community) pixpaper display
> + * support on NXP FRDM i.MX 93 Development Board
> + *
> + * Copyright (C) 2026 Wig Cheng <onlywig at gmail.com>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include "imx93-pinfunc.h"
> +
> +/dts-v1/;
> +/plugin/;
> +
> +&iomuxc {
> +	pinctrl_lpspi3: lpspi3grp {
> +		fsl,pins = <
> +			MX93_PAD_GPIO_IO08__GPIO2_IO08		0x3fe /* SPI3 CE0 */
> +			MX93_PAD_GPIO_IO09__LPSPI3_SIN		0x3fe /* SPI3 MISO */
> +			MX93_PAD_GPIO_IO10__LPSPI3_SOUT		0x3fe /* SPI3 MOSI */
> +			MX93_PAD_GPIO_IO11__LPSPI3_SCK		0x3fe /* SPI3 CLK */
> +		>;
> +	};
> +
> +	pinctrl_epd_ctrl: epdctrlgrp {
> +		fsl,pins = <
> +			MX93_PAD_GPIO_IO05__GPIO2_IO05		0x31e /* DC pin */
> +			MX93_PAD_GPIO_IO06__GPIO2_IO06		0x31e /* RESET pin */
> +			MX93_PAD_GPIO_IO26__GPIO2_IO26		0x31e /* BUSY pin */
> +		>;
> +	};
> +};
> +
> +&lpspi3 {
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_lpspi3>, <&pinctrl_epd_ctrl>;
> +	cs-gpios = <&gpio2 8 GPIO_ACTIVE_LOW>;
> +	fsl,spi-num-chipselects = <1>;
> +	status = "okay";
> +
> +	display at 0 {
> +		compatible = "mayqueen,pixpaper";
> +		reg = <0>;
> +		spi-max-frequency = <5000000>;
> +		reset-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
> +		dc-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>;
> +		busy-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> +	};
> +};
> --
> 2.43.0
>