[PATCH v4 2/2] arm64: dts: rockchip: Add rk3576 evb2 board

[Chaoyi Chen]

Hi Shawn,

On 1/21/2026 10:09 AM, Shawn Lin wrote:
> 在 2026/01/21 星期三 9:53, Chaoyi Chen 写道:
>> From: Chaoyi Chen <chaoyi.chen at rock-chips.com>
>>
>> General features for rk3576 evb2 board:
>>      - Rockchip RK3576
>>      - LPDDR4/4X
>>      - eMMC5.1
>>      - RK806-2x2pcs + DiscretePower
>>      - 1x HDMI2.1 TX / HDMI2.0 RX
>>      - 1x full size DP1.4 TX (Only 2 Lanes)
>>      - 2x 10/100/1000M Ethernet
>>      - 5x SATA3.0 7Pin Slot
>>      - 2x USB3.2 Gen1 Host
>>      - 3x USB2.0 Host
>>      - WIFI/BT
>>      - ...
>>
>> Tested with eMMC/SDMMC/HDMI/USB/Ethernet/WIFI/BT module.
>>
>> Signed-off-by: Chaoyi Chen <chaoyi.chen at rock-chips.com>
>> Reviewed-by: Alexey Charkov <alchark at gmail.com>
>> ---
> 
> ---8<----
> 
>> +
>> +&sdio {
>> +    #address-cells = <1>;
>> +    #size-cells = <0>;
>> +    bus-width = <4>;
>> +    cap-sd-highspeed;
>> +    cap-sdio-irq;
>> +    disable-wp;
> 
> disable-wp is not used for SDIO case, could be removed.
> 
> 

Will fix in v5.

>> +    keep-power-in-suspend;
>> +    max-frequency = <150000000>;
>> +    mmc-pwrseq = <&sdio_pwrseq>;
>> +    no-sd;
>> +    no-mmc;
>> +    non-removable;
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&sdmmc1m0_bus4 &sdmmc1m0_clk &sdmmc1m0_cmd>;
>> +    sd-uhs-sdr104;
>> +    status = "okay";
>> +
>> +    brcmf: wifi at 1 {
>> +        compatible = "brcm,bcm4329-fmac";
>> +        reg = <1>;
>> +        interrupt-parent = <&gpio0>;
>> +        interrupts = <RK_PB0 IRQ_TYPE_LEVEL_HIGH>;
>> +        interrupt-names = "host-wake";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&wifi_host_wake>;
>> +    };
>> +};
>> +
>> +&sdhci {
>> +    bus-width = <8>;
>> +    full-pwr-cycle-in-suspend;
>> +    mmc-hs400-1_8v;
>> +    mmc-hs400-enhanced-strobe;
>> +    no-sdio;
>> +    no-sd;
>> +    non-removable;
>> +    status = "okay";
>> +};
>> +
>> +&sdmmc {
>> +    bus-width = <4>;
>> +    cap-sd-highspeed;
>> +    cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
>> +    disable-wp;
>> +    no-sdio;
>> +    no-mmc;
>> +    sd-uhs-sdr104;
>> +    vqmmc-supply = <&vccio_sd_s0>;
> 
> Should use vmmc-supply to contrl the power, the same as EVB1[1].
> 
> [1] https://lore.kernel.org/linux-rockchip/1768524932-163929-5-git-send-email-shawn.lin@rock-chips.com/T/#u
> 

That make sense. Will fix in v5.

>> +    status = "okay";
>> +};
>> +
>> +&u2phy0 {
>> +    status = "okay";
>> +};
>> +
> 
> 
> 
> 

-- 
Best, 
Chaoyi