[PATCH 2/2] arm64: dts: rockchip: Add Orange Pi 5 Pro board support
dennis at ausil.us
dennis at ausil.us
Sat Feb 28 12:54:17 PST 2026
From: Dennis Gilmore <dennis at ausil.us>
Add device tree for the Xunlong Orange Pi 5 Pro (RK3588S). The Pro
differs from the base Orange Pi 5 in the following ways:
- No SPI NOR flash; eMMC module slot instead, you can optionally solder
a SPI NOR fin place and turn off the eMMC
- PCIe-attached NIC (pcie2x1l1) replaces the GMAC1 ethernet
- PCIe NVMe slot (pcie2x1l2)
- AP6256 WiFi (BCM43456) via SDIO with mmc-pwrseq
- BCM4345C5 Bluetooth via uart9 with full RTS/CTS
- Two-colour (blue/green) GPIO LED using modern color/function binding
- audio is wired up differently
Vendors description and links to schematics available:
http://www.orangepi.org/html/hardWare/computerAndMicrocontrollers/details/Orange-Pi-5-Pro.html
Signed-off-by: Dennis Gilmore <dennis at ausil.us>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3588s-orangepi-5-pro.dts | 376 ++++++++++++++++++
2 files changed, 377 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 4d384f153c13..c99dca2ae9e7 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -214,6 +214,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5b.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-5-pro.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-orangepi-cm5-base.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-radxa-cm5-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-roc-pc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
new file mode 100644
index 000000000000..d656328c906d
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-orangepi-5-pro.dts
@@ -0,0 +1,376 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3588s-orangepi-5.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 5 Pro";
+ compatible = "xunlong,orangepi-5-pro", "rockchip,rk3588s";
+
+ aliases {
+ /delete-property/ ethernet0;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ mmc2 = &sdio;
+ };
+
+ /* Pro uses gpio-leds instead; pwm0 LED is not wired up */
+ /delete-node/ pwm-leds;
+
+ /*
+ * Pro uses i2s2 (i2s2m1 mux) for audio, not i2s1. Recreate the sound
+ * card node pointing at i2s2_2ch instead.
+ */
+ /delete-node/ analog-sound;
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpios = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ simple-audio-card,name = "rockchip,es8388";
+ simple-audio-card,routing =
+ "Headphones", "LOUT1",
+ "Headphones", "ROUT1",
+ "LINPUT1", "Microphone Jack",
+ "RINPUT1", "Microphone Jack",
+ "LINPUT2", "Onboard Microphone",
+ "RINPUT2", "Onboard Microphone";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Microphone", "Onboard Microphone",
+ "Headphone", "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s2_2ch>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ system-clock-frequency = <12288000>;
+ };
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ #cooling-cells = <2>;
+ cooling-levels = <0 50 100 150 200 255>;
+ fan-supply = <&vcc5v0_sys>;
+ pwms = <&pwm2 0 20000000 0>;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_rgb>;
+
+ blue-led {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ green-led {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_ACTIVITY;
+ gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "mmc0";
+ };
+ };
+
+ vcc5v0_otg: regulator-vcc5v0-otg {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&vcc5v0_otg_en>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <5000000>;
+ regulator-min-microvolt = <5000000>;
+ regulator-name = "vcc5v0_otg";
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&hym8563>;
+ clock-names = "ext_clock";
+ post-power-on-delay-ms = <200>;
+ reset-gpios = <&gpio0 RK_PD0 GPIO_ACTIVE_LOW>;
+ };
+
+ vcc3v3_pcie20: regulator-vcc3v3-pcie20 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_HIGH>;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pcie20";
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc3v3_pcie_eth: regulator-vcc3v3-pcie-eth {
+ compatible = "regulator-fixed";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-max-microvolt = <3300000>;
+ regulator-min-microvolt = <3300000>;
+ regulator-name = "vcc3v3_pcie_eth";
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+/* disable gmac1 as the pro has a PCIe attached NIC */
+&gmac1 {
+ status = "disabled";
+};
+
+/* 40-pin header pins 3/5 */
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1m4_xfer>;
+ status = "okay";
+};
+
+/*
+ * Pro routes audio codec via i2c3 (not i2c6) and i2s2m1 (not i2s1m0).
+ * Delete the inherited es8388 node from i2c6 and redeclare it here.
+ */
+/delete-node/ &es8388;
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c3m0_xfer>;
+ status = "okay";
+
+ es8388: audio-codec at 11 {
+ compatible = "everest,es8388", "everest,es8328";
+ reg = <0x11>;
+ #sound-dai-cells = <0>;
+ AVDD-supply = <&vcc_3v3_s0>;
+ DVDD-supply = <&vcc_1v8_s0>;
+ HPVDD-supply = <&vcc_3v3_s0>;
+ PVDD-supply = <&vcc_3v3_s0>;
+ assigned-clock-rates = <12288000>;
+ assigned-clocks = <&cru I2S2_2CH_MCLKOUT>;
+ clocks = <&cru I2S2_2CH_MCLKOUT>;
+ };
+};
+
+/* 40-pin header pins 27/28 */
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c4m3_xfer>;
+ status = "okay";
+};
+
+/*
+ * i2s1_8ch uses i2s1m0 which occupies GPIO4_PA0 (CLKREQ#) and GPIO4_PA1
+ * (WAKE#) needed for the NVMe M.2 slot. Disable it; audio is on i2s2_2ch.
+ */
+&i2s1_8ch {
+ status = "disabled";
+};
+
+/* Audio codec on i2s2, m1 mux; add mclk pin to the base pinctrl */
+&i2s2_2ch {
+ pinctrl-0 = <&i2s2m1_lrck &i2s2m1_mclk &i2s2m1_sclk
+ &i2s2m1_sdi &i2s2m1_sdo>;
+ status = "okay";
+};
+
+&package_thermal {
+ polling-delay = <1000>;
+
+ cooling-maps {
+ map0 {
+ trip = <&package_fan0>;
+ cooling-device = <&fan THERMAL_NO_LIMIT 1>;
+ };
+
+ map1 {
+ trip = <&package_fan1>;
+ cooling-device = <&fan 2 THERMAL_NO_LIMIT>;
+ };
+ };
+
+ trips {
+ package_fan0: package-fan0 {
+ hysteresis = <2000>;
+ temperature = <55000>;
+ type = "active";
+ };
+
+ package_fan1: package-fan1 {
+ hysteresis = <2000>;
+ temperature = <65000>;
+ type = "active";
+ };
+ };
+};
+
+/* NVMe */
+&pcie2x1l1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie30x1m1_1_clkreqn &pcie30x1m1_1_waken>;
+ reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
+ supports-clkreq;
+ vpcie3v3-supply = <&vcc3v3_pcie_eth>;
+ status = "okay";
+};
+
+/* NIC */
+&pcie2x1l2 {
+ reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie20>;
+ status = "okay";
+};
+
+&pinctrl {
+ bluetooth {
+ bt_wake_gpio: bt-wake-pin {
+ rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ bt_wake_host_irq: bt-wake-host-irq {
+ rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ gpio-leds {
+ leds_rgb: leds-rgb {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>,
+ <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ vcc5v0_otg_en: vcc5v0-otg-en {
+ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ wlan {
+ wifi_host_wake_irq: wifi-host-wake-irq {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+};
+
+/* pwm0 pin conflicts with i2c4 pin 27 Pro */
+&pwm0 {
+ status = "disabled";
+};
+
+&pwm2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm2m1_pins>;
+ status = "okay";
+};
+
+&sdhci {
+ status = "okay";
+};
+
+&sdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ bus-width = <4>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ disable-wp;
+ keep-power-in-suspend;
+ max-frequency = <150000000>;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ no-mmc;
+ no-sd;
+ non-removable;
+ sd-uhs-sdr104;
+ status = "okay";
+
+ ap6256: wifi at 1 {
+ compatible = "brcm,bcm43456-fmac", "brcm,bcm4329-fmac";
+ reg = <1>;
+ interrupt-names = "host-wake";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA0 IRQ_TYPE_LEVEL_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_host_wake_irq>;
+ };
+};
+
+&uart9 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart9m2_xfer &uart9m2_ctsn &uart9m2_rtsn>;
+ uart-has-rtscts;
+ status = "okay";
+
+ bluetooth {
+ compatible = "brcm,bcm4345c5";
+ clocks = <&hym8563>;
+ clock-names = "lpo";
+ device-wakeup-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_HIGH>;
+ interrupt-names = "host-wakeup";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PC5 IRQ_TYPE_LEVEL_HIGH>;
+ max-speed = <1500000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_wake_host_irq &bt_wake_gpio>;
+ shutdown-gpios = <&gpio0 RK_PD5 GPIO_ACTIVE_HIGH>;
+ vbat-supply = <&vcc_3v3_s3>;
+ vddio-supply = <&vcc_1v8_s3>;
+ };
+};
+
+/* USB2 OTG PHY for usb_host0_xhci; phy-supply enables VBUS to USB3 Type-A port */
+&u2phy0_otg {
+ phy-supply = <&vcc5v0_otg>;
+};
+
+/* Pro has no FUSB302; the USB-C port is power delivery only */
+/delete-node/ &usbc0;
+
+/*
+ * The Pro's USB-C port is power delivery only: no FUSB302, no data lines,
+ * no alt-mode switching. The parent DTSI enables usbdp_phy0 (status = "okay")
+ * and adds FUSB302 alt-mode/orientation properties; delete those here.
+ *
+ * dp-lane-mux = <0 1>: PHY lanes 0/1 are DP (physically routed to the
+ * LT8711UXD DP→HDMI2 bridge), lanes 2/3 are USB3 SuperSpeed (physically
+ * routed to the USB3 Type-A port P3). Without this property the driver
+ * defaults to USB-only mode and places USB3 on lanes 0/1, which do not
+ * reach the Type-A connector and makes the USB3 port non-functional.
+ */
+&usbdp_phy0 {
+ rockchip,dp-lane-mux = <0 1>;
+ /delete-property/ mode-switch;
+ /delete-property/ orientation-switch;
+ /delete-property/ sbu1-dc-gpios;
+ /delete-property/ sbu2-dc-gpios;
+ /delete-node/ port;
+};
+
+/* USB3 Type-A port*/
+&usb_host0_xhci {
+ dr_mode = "host";
+ /delete-property/ usb-role-switch;
+ status = "okay";
+ /delete-node/ port;
+};
+
+/*
+ * combphy2_psu is shared between usb_host2_xhci (USB3) and pcie2x1l1 (PCIe).
+ * Disable USB3 so the PHY can be used for the NVMe M.2 slot.
+ */
+&usb_host2_xhci {
+ status = "disabled";
+};
--
2.53.0
More information about the linux-arm-kernel
mailing list