[PATCH] ARM: tegra: paz00: configure WiFi rfkill switch through device tree

[Dmitry Torokhov]

Hi Marc,

On Sat, Feb 21, 2026 at 03:24:35PM +0100, Marc Dietrich wrote:
> Hi Dmitry,
> 
> On Sat, 14 Feb 2026, Marc Dietrich wrote:
> 
> > Hi Dmitry,
> > 
> > On Fri, 13 Feb 2026, Dmitry Torokhov wrote:
> > 
> > > As of d64c732dfc9e ("net: rfkill: gpio: add DT support") rfkill-gpio
> > > device can be instantiated via device tree.
> > > 
> > > Add the declaration there and drop board-paz00.c file and relevant
> > > Makefile fragments.
> > > 
> > > Signed-off-by: Dmitry Torokhov <dmitry.torokhov at gmail.com>
> > > ---
> > > 
> > > This is not tested on real hardware, compile tested only...
> > > 
> > > arch/arm/boot/dts/nvidia/tegra20-paz00.dts |  8 ++++
> > > arch/arm/mach-tegra/Makefile               |  2 -
> > > arch/arm/mach-tegra/board-paz00.c          | 56 ----------------------
> > > arch/arm/mach-tegra/board.h                |  2 -
> > > arch/arm/mach-tegra/tegra.c                |  4 --
> > > 5 files changed, 8 insertions(+), 64 deletions(-)
> > > 
> > > diff --git a/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
> > > b/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
> > > index 1408e1e00759..d1093ad569e6 100644
> > > --- a/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
> > > +++ b/arch/arm/boot/dts/nvidia/tegra20-paz00.dts
> > > @@ -706,6 +706,14 @@ vdd_pnl_reg: regulator-3v0 {
> > > 		enable-active-high;
> > > 	};
> > > 
> > > +	rfkill {
> > > +		compatible = "rfkill-gpio";
> > > +		label = "wifi_rfkill";
> > > +		radio-type = "wlan";
> > > +		reset-gpios = <&gpio TEGRA_GPIO(D, 1) GPIO_ACTIVE_HIGH>;
> > 
> > I guess this can be removed, as it should trigger the LED, which is
> > already included elsewhere ....
> > 
> > > +		shutdown-gpios = <&gpio TEGRA_GPIO(K, 5) GPIO_ACTIVE_HIGH>;
> > > +	};
> > > +
> > > 	sound {
> > > 		compatible = "nvidia,tegra-audio-alc5632-paz00",
> > > 			"nvidia,tegra-audio-alc5632";
> > 
> > I'll give it a try and report back.
> 
> rfkill (and LED) works as expected. With the reset-gpio line mentioned above
> removed, you can add my Tested-By.

Thank you Marc.

I am still a bit confused about the reset gpio. As far as I understand
looking through old commits reset gpio (PD1) is distinct from the LED
gpio (PD0) that is currently being controlled by "gpio-leds".

I guess the rfkill driver needs at least one of "reset" or "shutdown"
gpios, and that is why it continues to work with only shutdown, but I am
trying to understand if PD1 was never connected to the WiFi chip reset
line and instead is used for something else, or if it is indeed a reset
line...

Was the patch not working with reset-gpios present? I am trying to
gather data to craft a proper commit message.

Thanks.

-- 
Dmitry