[PATCH 1/3] ARM: dts: imx27-eukrea: replace interrupts with interrupts-extended

[Frank Li]

The property interrupts use default interrupt controllers. But pass down
gpio<n> as phandle. Correct it by use interrupts-extended.

Fixes: d8cae888aa2bc ("ARM: dts: Add support for the cpuimx27 board from Eukrea and its baseboard")
Signed-off-by: Frank Li <Frank.Li at nxp.com>
---
Try to fix CHECK_DTB warnings, but found it is functional block. Support
irq never worked before.
arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dtb: serial at 3,200000 (ns8250): interrupts: [[28], [23], [8]] is too long
        from schema $id: http://devicetree.org/schemas/serial/8250.yaml
---
 arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi           | 8 ++++----
 arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts | 2 +-
 2 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
index bc28250df7a7fb729c2ef76b1f4b3c1199e7f1ba..87dd80fc7061eeef88eeb353edb042b9a631a356 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-cpuimx27.dtsi
@@ -110,7 +110,7 @@ uart8250 at 3,200000 {
 		compatible = "ns8250";
 		clocks = <&clk14745600>;
 		fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
-		interrupts = <&gpio2 23 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio2 23 IRQ_TYPE_LEVEL_LOW>;
 		reg = <3 0x200000 0x1000>;
 		reg-shift = <1>;
 		reg-io-width = <1>;
@@ -123,7 +123,7 @@ uart8250 at 3,400000 {
 		compatible = "ns8250";
 		clocks = <&clk14745600>;
 		fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
-		interrupts = <&gpio2 22 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio2 22 IRQ_TYPE_LEVEL_LOW>;
 		reg = <3 0x400000 0x1000>;
 		reg-shift = <1>;
 		reg-io-width = <1>;
@@ -136,7 +136,7 @@ uart8250 at 3,800000 {
 		compatible = "ns8250";
 		clocks = <&clk14745600>;
 		fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
-		interrupts = <&gpio2 27 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio2 27 IRQ_TYPE_LEVEL_LOW>;
 		reg = <3 0x800000 0x1000>;
 		reg-shift = <1>;
 		reg-io-width = <1>;
@@ -149,7 +149,7 @@ uart8250 at 3,1000000 {
 		compatible = "ns8250";
 		clocks = <&clk14745600>;
 		fsl,weim-cs-timing = <0x0000d603 0x0d1d0d01 0x00d20000>;
-		interrupts = <&gpio2 30 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio2 30 IRQ_TYPE_LEVEL_LOW>;
 		reg = <3 0x1000000 0x1000>;
 		reg-shift = <1>;
 		reg-io-width = <1>;
diff --git a/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
index 1c834f2f5068d16174c086c1fe540ff371444675..26833ed3339e26ca88d36c4ae1b52a30943e649e 100644
--- a/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
+++ b/arch/arm/boot/dts/nxp/imx/imx27-eukrea-mbimxsd27-baseboard.dts
@@ -76,7 +76,7 @@ ads7846 at 0 {
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_touch>;
 		reg = <0>;
-		interrupts = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>;
+		interrupts-extended = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>;
 		spi-cpol;
 		spi-max-frequency = <1500000>;
 		ti,keep-vref-on;

-- 
2.43.0