[PATCH V3 03/10] arm: dts: imx6qdl: Add Root Port node and PERST property

[Sherry Sun]

> On Tue, Feb 03, 2026 at 09:56:07AM +0800, Sherry Sun wrote:
> > Since describing the PCIe PERST# property under Host Bridge node is
> > now deprecated, it is recommended to add it to the Root Port node, so
> > creating the Root Port node and add the reset-gpios property in Root
> > Port.
> >
> > Signed-off-by: Sherry Sun <sherry.sun at nxp.com>
> > ---
> >  arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi |  5 +++++
> >  arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi         | 11 +++++++++++
> >  arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts |  5 +++++
> >  3 files changed, 21 insertions(+)
> >
> > diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
> > b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
> > index ba29720e3f72..fe9046c03ddd 100644
> > --- a/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
> > +++ b/arch/arm/boot/dts/nxp/imx/imx6qdl-sabresd.dtsi
> > @@ -754,11 +754,16 @@ lvds0_out: endpoint {  &pcie {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_pcie>;
> > +	/* This property is deprecated, use reset-gpios from the Root Port
> > +node. */
> >  	reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
> 
> You should just remove this property.

Hi Manivannan,

Actually I have discussed with Frank about this in V1, Frank suggested add
comments here instead of removing the old property, just in case the dts
used by old kernel to avoid function break. Or maybe we can at least keep it
for some kernel release, then remove it later.

Best Regards
Sherry
> 
> >  	vpcie-supply = <&reg_pcie>;
> >  	status = "okay";
> >  };
> >
> > +&pcie_port0 {
> > +	reset-gpios = <&gpio7 12 GPIO_ACTIVE_LOW>; };
> > +
> >  &pwm1 {
> >  	pinctrl-names = "default";
> >  	pinctrl-0 = <&pinctrl_pwm1>;
> > diff --git a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
> > b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
> > index 76e6043e1f91..eeb376193398 100644
> > --- a/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
> > +++ b/arch/arm/boot/dts/nxp/imx/imx6qdl.dtsi
> > @@ -289,6 +289,17 @@ pcie: pcie at 1ffc000 {
> >  				 <&clks IMX6QDL_CLK_PCIE_REF_125M>;
> >  			clock-names = "pcie", "pcie_bus", "pcie_phy";
> >  			status = "disabled";
> > +
> > +			pcie_port0: pcie at 0 {
> > +				compatible = "pciclass,0604";
> > +				device_type = "pci";
> > +				reg = <0x0 0x0 0x0 0x0 0x0>;
> > +				bus-range = <0x01 0xff>;
> > +
> > +				#address-cells = <3>;
> > +				#size-cells = <2>;
> > +				ranges;
> > +			};
> >  		};
> >
> >  		aips1: bus at 2000000 { /* AIPS1 */
> > diff --git a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
> > b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
> > index c5b220aeaefd..6b12cab7175f 100644
> > --- a/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
> > +++ b/arch/arm/boot/dts/nxp/imx/imx6qp-sabreauto.dts
> > @@ -45,10 +45,15 @@ MX6QDL_PAD_GPIO_6__ENET_IRQ
> 	0x000b1
> >  };
> >
> >  &pcie {
> > +	/* This property is deprecated, use reset-gpios from the Root Port
> > +node. */
> >  	reset-gpio = <&max7310_c 5 GPIO_ACTIVE_LOW>;
> >  	status = "okay";
> >  };
> >
> > +&pcie_port0 {
> > +	reset-gpios = <&max7310_c 5 GPIO_ACTIVE_LOW>; };
> > +
> >  &sata {
> >  	status = "okay";
> >  };
> > --
> > 2.37.1
> >
> 
> --
> மணிவண்ணன் சதாசிவம்