[PATCH 6/6] arm64: dts: rockchip: add QNAP TS233 devicetree

Heiko Stuebner heiko at sntech.de
Thu Sep 25 02:29:23 PDT 2025


The TS233 is a 2 bay NAS similar to the TS433. Architecture-wise it really
seems to be the same minus the additional PCIe connected components the
TS433 has.

So it just uses two of the SoCs SATA ports and the SoC's gigabit ethernet.

Signed-off-by: Heiko Stuebner <heiko at sntech.de>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../boot/dts/rockchip/rk3568-qnap-ts233.dts   | 133 ++++++++++++++++++
 2 files changed, 134 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 099520962ffb..f1b7917ae22b 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -136,6 +136,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-odroid-m1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-photonicat.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts233.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-qnap-ts433.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-radxa-e25.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-roc-pc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts
new file mode 100644
index 000000000000..29181de1bd26
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3568-qnap-ts233.dts
@@ -0,0 +1,133 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright (c) 2021 Rockchip Electronics Co., Ltd.
+ * Copyright (c) 2024 Heiko Stuebner <heiko at sntech.de>
+ */
+
+/dts-v1/;
+
+#include "rk3568-qnap-tsx33.dtsi"
+
+/ {
+	model = "Qnap TS-233-2G NAS System 2-Bay";
+	compatible = "qnap,ts233", "rockchip,rk3568";
+
+	aliases {
+		ethernet0 = &gmac0;
+	};
+};
+
+/* connected to sata2 */
+&combphy2 {
+	status = "okay";
+};
+
+&gmac0 {
+	assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>;
+	assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>;
+	assigned-clock-rates = <0>, <125000000>;
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy0>;
+	phy-mode = "rgmii-id";
+	pinctrl-names = "default";
+	pinctrl-0 = <&gmac0_miim
+		     &gmac0_tx_bus2
+		     &gmac0_rx_bus2
+		     &gmac0_rgmii_clk
+		     &gmac0_rgmii_bus>;
+	rx_delay = <0x15>;
+	tx_delay = <0x21>;
+	status = "okay";
+};
+
+&i2c1 {
+	/* eeprom for vital-product-data on the backplane */
+	eeprom at 56 {
+		compatible = "giantec,gt24c04a", "atmel,24c04";
+		reg = <0x56>;
+		label = "VPD_BP";
+		num-addresses = <2>;
+		pagesize = <16>;
+		read-only;
+	};
+};
+
+&leds {
+	led-1 {
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_DISK;
+		gpios = <&gpio1 RK_PD6 GPIO_ACTIVE_LOW>;
+		label = "hdd2:green:disk";
+		linux,default-trigger = "disk-activity";
+		pinctrl-names = "default";
+		pinctrl-0 = <&hdd2_led_pin>;
+	};
+};
+
+&mcu {
+	compatible = "qnap,ts233-mcu";
+};
+
+&mdio0 {
+	rgmii_phy0: ethernet-phy at 3 {
+		/* Motorcomm YT8521 phy */
+		compatible = "ethernet-phy-ieee802.3-c22";
+		reg = <0x3>;
+		pinctrl-0 = <&eth_phy0_reset_pin>;
+		pinctrl-names = "default";
+		reset-assert-us = <10000>;
+		reset-gpios = <&gpio0 RK_PC6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pinctrl {
+	gmac0 {
+		eth_phy0_reset_pin: eth-phy0-reset-pin {
+			rockchip,pins = <0 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	leds {
+		hdd2_led_pin: hdd2-led-pin {
+			rockchip,pins = <1 RK_PD6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
+
+&sata2 {
+	status = "okay";
+};
+
+&usb2phy1 {
+	status = "okay";
+};
+
+/* connected to usb_host1_ehci/ohci */
+&usb2phy1_host {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+/* connected to usb_host0_ehci/ohci */
+&usb2phy1_otg {
+	phy-supply = <&vcc5v0_host>;
+	status = "okay";
+};
+
+/* right port backside */
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+/* left port backside */
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
-- 
2.47.2




More information about the linux-arm-kernel mailing list