[PATCH v2 3/4] arm64: dts: marvell: cn9132-clearfog: fix multi-lane pci x2 and x4 ports

[Gregory CLEMENT]

Josua Mayer <josua at solid-run.com> writes:

> The mvebu-comphy driver does not currently know how to pass correct
> lane-count to ATF while configuring the serdes lanes.
>
> This causes the system to hard reset during reconfiguration, if a pci
> card is present and has established a link during bootloader.
>
> Remove the comphy handles from the respective pci nodes to avoid runtime
> reconfiguration, relying solely on bootloader configuration - while
> avoiding the hard reset.
>
> When bootloader has configured the lanes correctly, the pci ports are
> functional under Linux.
>
> This issue may be addressed in the comphy driver at a future point.
>
> Fixes: e9ff907f4076 ("arm64: dts: add description for solidrun cn9132 cex7 module and clearfog board")
> Cc: <stable at vger.kernel.org>
> Signed-off-by: Josua Mayer <josua at solid-run.com>

Applied on mvebu/fixes

Thanks,

Gregory

> ---
>  arch/arm64/boot/dts/marvell/cn9132-clearfog.dts | 16 ++++++++++++++--
>  1 file changed, 14 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/marvell/cn9132-clearfog.dts b/arch/arm64/boot/dts/marvell/cn9132-clearfog.dts
> index 115c55d73786e2b9265e1caa4c62ee26f498fb41..6f237d3542b9102695f8a48457f43340da994a2c 100644
> --- a/arch/arm64/boot/dts/marvell/cn9132-clearfog.dts
> +++ b/arch/arm64/boot/dts/marvell/cn9132-clearfog.dts
> @@ -413,7 +413,13 @@ fixed-link {
>  /* SRDS #0,#1,#2,#3 - PCIe */
>  &cp0_pcie0 {
>  	num-lanes = <4>;
> -	phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>, <&cp0_comphy2 0>, <&cp0_comphy3 0>;
> +	/*
> +	 * The mvebu-comphy driver does not currently know how to pass correct
> +	 * lane-count to ATF while configuring the serdes lanes.
> +	 * Rely on bootloader configuration only.
> +	 *
> +	 * phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>, <&cp0_comphy2 0>, <&cp0_comphy3 0>;
> +	 */
>  	status = "okay";
>  };
>  
> @@ -475,7 +481,13 @@ &cp1_eth0 {
>  /* SRDS #0,#1 - PCIe */
>  &cp1_pcie0 {
>  	num-lanes = <2>;
> -	phys = <&cp1_comphy0 0>, <&cp1_comphy1 0>;
> +	/*
> +	 * The mvebu-comphy driver does not currently know how to pass correct
> +	 * lane-count to ATF while configuring the serdes lanes.
> +	 * Rely on bootloader configuration only.
> +	 *
> +	 * phys = <&cp1_comphy0 0>, <&cp1_comphy1 0>;
> +	 */
>  	status = "okay";
>  };
>  
>
> -- 
> 2.51.0
>
>

-- 
Grégory CLEMENT, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com