[PATCH 2/2] arm64: dts: allwinner: h313: Add Amediatech X96Q
J. Neuschäfer via B4 Relay
devnull+j.ne.posteo.net at kernel.org
Thu Sep 11 16:52:10 PDT 2025
From: "J. Neuschäfer" <j.ne at posteo.net>
The X96Q is a set-top box with an H313 SoC, AXP305 PMIC, 1 or 2 GiB RAM,
8 or 16 GiB eMMC flash, 2x USB A, Micro-SD, HDMI, Ethernet, audio/video
output, and infrared input.
https://x96mini.com/products/x96q-tv-box-android-10-set-top-box
Tested, works:
- debug UART
- status LED
- USB ports in host mode
- MicroSD
- eMMC
- recovery button hidden behind audio/video port
- analog audio (line out)
Does not work:
- Ethernet (requires AC200 MFD/EPHY driver)
- analog video output (requires AC200 driver)
- HDMI audio/video output
Untested:
- "OTG" USB port in device mode
- built-in IR receiver
- external IR receiver
- WLAN (requires out-of-tree XRadio driver)
Table of regulators on the downstream kernel, for reference:
vcc-5v 1 15 0 unknown 5000mV 0mA 5000mV 5000mV
dcdca 0 0 0 unknown 900mV 0mA 0mV 0mV
dcdcb 0 0 0 unknown 1350mV 0mA 0mV 0mV
dcdcc 0 0 0 unknown 900mV 0mA 0mV 0mV
dcdcd 0 0 0 unknown 1500mV 0mA 0mV 0mV
dcdce 0 0 0 unknown 3300mV 0mA 0mV 0mV
aldo1 0 0 0 unknown 3300mV 0mA 0mV 0mV
aldo2 0 0 0 unknown 700mV 0mA 0mV 0mV
aldo3 0 0 0 unknown 700mV 0mA 0mV 0mV
bldo1 0 0 0 unknown 1800mV 0mA 0mV 0mV
bldo2 0 0 0 unknown 1800mV 0mA 0mV 0mV
bldo3 0 0 0 unknown 700mV 0mA 0mV 0mV
bldo4 0 0 0 unknown 700mV 0mA 0mV 0mV
cldo1 0 0 0 unknown 2500mV 0mA 0mV 0mV
cldo2 0 0 0 unknown 700mV 0mA 0mV 0mV
cldo3 0 0 0 unknown 700mV 0mA 0mV 0mV
Signed-off-by: J. Neuschäfer <j.ne at posteo.net>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
arch/arm64/boot/dts/allwinner/sun50i-h313-x96q.dts | 235 +++++++++++++++++++++
2 files changed, 236 insertions(+)
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 780aeba0f3a4e14d69c9602e37b8d299165507b9..2edfa7bf4ab31c4aa934da98e5e042edc9aaf600 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -41,6 +41,7 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6-mini.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h313-tanix-tx1.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h313-x96q.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-cb1-manta.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-bigtreetech-pi.dtb
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h313-x96q.dts b/arch/arm64/boot/dts/allwinner/sun50i-h313-x96q.dts
new file mode 100644
index 0000000000000000000000000000000000000000..9534eb03b89557f2545af5af7cf43390be722cf0
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h313-x96q.dts
@@ -0,0 +1,235 @@
+// SPDX-License-Identifier: (GPL-2.0-or-later OR MIT)
+/*
+ * Copyright (C) 2025 J. Neuschäfer <j.ne at posteo.net>
+ */
+
+/dts-v1/;
+
+#include "sun50i-h616.dtsi"
+#include "sun50i-h616-cpu-opp.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+ model = "X96Q";
+ compatible = "amediatech,x96q", "allwinner,sun50i-h616";
+
+ aliases {
+ mmc0 = &mmc0;
+ mmc1 = &mmc1;
+ mmc2 = &mmc2;
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_vcc5v: vcc5v {
+ /* board wide 5V supply directly from the DC input */
+ compatible = "regulator-fixed";
+ regulator-name = "vcc-5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-always-on;
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ key-recovery {
+ label = "Recovery";
+ linux,code = <KEY_VENDOR>;
+ gpios = <&pio 7 9 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led-0 {
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pio 7 6 GPIO_ACTIVE_LOW>;
+ default-state = "on";
+ };
+ };
+};
+
+&codec {
+ allwinner,audio-routing = "Line Out", "LINEOUT";
+ status = "okay";
+};
+
+&cpu0 {
+ cpu-supply = <®_dcdca>;
+};
+
+&ehci0 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+/* TODO: EMAC1 connected to AC200 PHY */
+
+&gpu {
+ mali-supply = <®_dcdcc>;
+ status = "okay";
+};
+
+&ir {
+ status = "okay";
+};
+
+&mmc0 {
+ vmmc-supply = <®_aldo1>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
+ disable-wp;
+ bus-width = <4>;
+ max-frequency = <150000000>;
+ status = "okay";
+ /* µSD */
+};
+
+&mmc1 {
+ /* TODO: XRadio XR819 WLAN */
+};
+
+&mmc2 {
+ vmmc-supply = <®_aldo1>;
+ vqmmc-supply = <®_bldo1>;
+ non-removable;
+ cap-mmc-hw-reset;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ bus-width = <8>;
+ max-frequency = <100000000>;
+ status = "okay";
+ /* eMMC */
+};
+
+&ohci0 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&r_i2c {
+ status = "okay";
+
+ axp305: pmic at 36 {
+ compatible = "x-powers,axp305", "x-powers,axp805",
+ "x-powers,axp806";
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ reg = <0x36>;
+
+ x-powers,self-working-mode;
+ vina-supply = <®_vcc5v>;
+ vinb-supply = <®_vcc5v>;
+ vinc-supply = <®_vcc5v>;
+ vind-supply = <®_vcc5v>;
+ vine-supply = <®_vcc5v>;
+ aldoin-supply = <®_vcc5v>;
+ bldoin-supply = <®_vcc5v>;
+ cldoin-supply = <®_vcc5v>;
+
+ regulators {
+ reg_dcdca: dcdca {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-name = "vdd-cpu";
+ };
+
+ dcdcb {
+ /* unused */
+ };
+
+ reg_dcdcc: dcdcc {
+ regulator-always-on;
+ regulator-min-microvolt = <810000>;
+ regulator-max-microvolt = <990000>;
+ regulator-name = "vdd-gpu-sys";
+ };
+
+ dcdcd {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ };
+
+ dcdce {
+ /* unused */
+ };
+
+ reg_aldo1: aldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc3v3";
+ };
+
+ aldo2 {
+ /* unused */
+ };
+
+ aldo3 {
+ /* unused */
+ };
+
+ reg_bldo1: bldo1 {
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc1v8";
+ };
+
+ bldo2 {
+ /* unused */
+ };
+
+ bldo3 {
+ /* unused */
+ };
+
+ bldo4 {
+ /* unused */
+ };
+
+ cldo1 {
+ /* unused */
+ };
+
+ cldo2 {
+ /* unused */
+ };
+
+ cldo3 {
+ /* unused */
+ };
+ };
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_ph_pins>;
+ status = "okay";
+};
+
+&usbotg {
+ dr_mode = "host"; /* USB A type receptacle */
+ status = "okay";
+};
+
+&usbphy {
+ status = "okay";
+};
--
2.48.0.rc1.219.gb6b6757d772
More information about the linux-arm-kernel
mailing list