[PATCH 0/4] Add CCI and imx577 sensor support for monaco evk

[Vikram Sharma]

Monaco EVK is a single board computer, based on the Qualcomm QCS8300 SoC.
This series adds CCI definition and enablement of imx577 sensor
via CCI1 on monaco evk.

We have tested IMX577 Sensor on CCI1 with following commands:
- media-ctl -d /dev/media0 --reset
- media-ctl -d /dev/media0 -V '"imx577 3-001a":0[fmt:SRGGB10/4056x3040
  field:none]'
- media-ctl -d /dev/media0 -V '"msm_csiphy1":0[fmt:SRGGB10/4056x3040]'
- media-ctl -d /dev/media0 -V '"msm_csiphy1":1[fmt:SRGGB10/4056x3040]'
- media-ctl -d /dev/media0 -V '"msm_csid0":0[fmt:SRGGB10/4056x3040]'
- media-ctl -d /dev/media0 -V '"msm_csid0":1[fmt:SRGGB10/4056x3040]'
- media-ctl -d /dev/media0 -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4056x3040]'
- media-ctl -d /dev/media0 -V '"msm_vfe0_rdi0":1[fmt:SRGGB10/4056x3040]'
- media-ctl -d /dev/media0 -l '"msm_csiphy1":1->"msm_csid0":0[1]'
- media-ctl -d /dev/media0 -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
- yavta -B capture-mplane -c -I -n 5 -f SRGGB10P -s 4056x3040 -F
  /dev/video1 --capture=5

Used following tools for the sanity check of these changes.

- make -j32 W=1
- checkpatch.pl
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml dt_binding_check
- make DT_CHECKER_FLAGS=-m W=1 DT_SCHEMA_FILES=media/qcom,qcs8300-camss.yaml dt_binding_check
- make CHECK_DTBS=y W=1 DT_SCHEMA_FILES=i2c/qcom,i2c-cci.yaml
- make CHECK_DTBS=y W=1 DT_SCHEMA_FILES=media/qcom,qcs8300-camss.yaml
---
This patch series depends on patch series:
https://lore.kernel.org/linux-arm-msm/20250814101615.1102795-1-quic_vikramsa@quicinc.com/
https://lore.kernel.org/all/20250813053724.232494-1-quic_vikramsa@quicinc.com/
---
Signed-off-by: Nihal Kumar Gupta <quic_nihalkum at quicinc.com>
Signed-off-by: Vikram Sharma <quic_vikramsa at quicinc.com>
---

Nihal Kumar Gupta (4):
  dt-bindings: i2c: qcom-cci: Document qcs8300 compatible
  arm64: dts: qcom: qcs8300: Add CCI definitions
  arm64: dts: qcom: monaco-evk-camera: Add DT overlay
  dt-bindings: media: camss: Add qcs8300 supplies binding

 .../devicetree/bindings/i2c/qcom,i2c-cci.yaml |   2 +
 .../bindings/media/qcom,qcs8300-camss.yaml    |  13 +
 arch/arm64/boot/dts/qcom/Makefile             |   4 +
 .../boot/dts/qcom/monaco-evk-camera.dtso      |  98 ++++++
 arch/arm64/boot/dts/qcom/qcs8300.dtsi         | 309 ++++++++++++++++++
 5 files changed, 426 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/monaco-evk-camera.dtso

-- 
2.25.1