[PATCH v8 3/4] arm64: dts: renesas: r9a09g047: Add TSU node

[John Madieu]

Add TSU node along with thermal zones and keep it enabled in the SoC DTSI.

Signed-off-by: John Madieu <john.madieu.xa at bp.renesas.com>
---

v1 -> v2: Fix IRQ names
v2 -> v3: remove useless 'renesas,tsu-operating-mode' property'
v3 -> v4: no changes
v5: no changes
v6: no changes
v7: updated both property name and specifier (<phandle offset>) for trim property.
v8: removed #address-cells property

 arch/arm64/boot/dts/renesas/r9a09g047.dtsi | 48 ++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/arm64/boot/dts/renesas/r9a09g047.dtsi b/arch/arm64/boot/dts/renesas/r9a09g047.dtsi
index e4fac7e0d764..7bf0b4a6c67a 100644
--- a/arch/arm64/boot/dts/renesas/r9a09g047.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a09g047.dtsi
@@ -64,6 +64,7 @@ cpu0: cpu at 0 {
 			next-level-cache = <&L3_CA55>;
 			enable-method = "psci";
 			clocks = <&cpg CPG_CORE R9A09G047_CA55_0_CORECLK0>;
+			#cooling-cells = <2>;
 			operating-points-v2 = <&cluster0_opp>;
 		};
 
@@ -74,6 +75,7 @@ cpu1: cpu at 100 {
 			next-level-cache = <&L3_CA55>;
 			enable-method = "psci";
 			clocks = <&cpg CPG_CORE R9A09G047_CA55_0_CORECLK1>;
+			#cooling-cells = <2>;
 			operating-points-v2 = <&cluster0_opp>;
 		};
 
@@ -84,6 +86,7 @@ cpu2: cpu at 200 {
 			next-level-cache = <&L3_CA55>;
 			enable-method = "psci";
 			clocks = <&cpg CPG_CORE R9A09G047_CA55_0_CORECLK2>;
+			#cooling-cells = <2>;
 			operating-points-v2 = <&cluster0_opp>;
 		};
 
@@ -94,6 +97,7 @@ cpu3: cpu at 300 {
 			next-level-cache = <&L3_CA55>;
 			enable-method = "psci";
 			clocks = <&cpg CPG_CORE R9A09G047_CA55_0_CORECLK3>;
+			#cooling-cells = <2>;
 			operating-points-v2 = <&cluster0_opp>;
 		};
 
@@ -412,6 +416,19 @@ wdt3: watchdog at 13000400 {
 			status = "disabled";
 		};
 
+		tsu: thermal at 14002000 {
+			compatible = "renesas,r9a09g047-tsu";
+			reg = <0 0x14002000 0 0x1000>;
+			interrupts = <GIC_SPI 250 IRQ_TYPE_EDGE_RISING>,
+				     <GIC_SPI 251 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "adi", "adcmpi";
+			clocks = <&cpg CPG_MOD 0x10a>;
+			resets = <&cpg 0xf8>;
+			power-domains = <&cpg>;
+			#thermal-sensor-cells = <0>;
+			renesas,tsu-trim = <&sys 0x330>;
+		};
+
 		i2c0: i2c at 14400400 {
 			compatible = "renesas,riic-r9a09g047", "renesas,riic-r9a09g057";
 			reg = <0 0x14400400 0 0x400>;
@@ -970,6 +987,37 @@ stmmac_axi_setup: stmmac-axi-config {
 		snps,blen = <16 8 4 0 0 0 0>;
 	};
 
+	thermal-zones {
+		cpu-thermal {
+			polling-delay = <1000>;
+			polling-delay-passive = <250>;
+			thermal-sensors = <&tsu>;
+
+			cooling-maps {
+				map0 {
+					trip = <&target>;
+					cooling-device = <&cpu0 0 3>, <&cpu1 0 3>,
+							 <&cpu2 0 3>, <&cpu3 0 3>;
+					contribution = <1024>;
+				};
+			};
+
+			trips {
+				target: trip-point {
+					temperature = <95000>;
+					hysteresis = <1000>;
+					type = "passive";
+				};
+
+				sensor_crit: sensor-crit {
+					temperature = <120000>;
+					hysteresis = <1000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
 	timer {
 		compatible = "arm,armv8-timer";
 		interrupts-extended = <&gic GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>,
-- 
2.25.1