[PATCH] ARM: dts: imx6ul-tx6ul: Switch away from deprecated `phy-reset-gpios`

[Ahmad Fatoum]

Hi,

On 03.09.25 09:43, Csókás Bence wrote:
> Hi,
> 
> On 2025. 09. 03. 9:28, Ahmad Fatoum wrote:
>> Hello,
>>
>> On 15.08.25 17:17, Bence Csókás wrote:
>>> The Ethernet PHY's reset GPIO should be specified in the node of the PHY
>>> itself, instead of the MAC (`fec`). The latter is deprecated, and was an
>>> i.MX-specific extension, incompatible with the new reset controller
>>> subsystem.
>>
>> One reason to do it this way is that the PHY is in reset when the OS starts
>> and the external phy-reset-gpios allows MAC probe to get the PHY out of
>> reset, so it can be probed after reading its vendor/device IDs.
>>
>> Does switching to this new binding address this scenario? If so, it should
>> be noted in the commit message.
> 
> Yes, but after it has been reset, if the platform supports Power Management, the PHY's clock will be turned off, which some PHYs (in our case the LAN8710) don't tolerate. This has been reported many times, just search LKML for "lan8710 reset".
> 
> So we want a more general solution [1] where the PHY subsystem resets them before enumerating. However, if the MAC driver claims the GPIO, then it can't be used by the PHY.

I agree that it makes sense for a PHY reset to be associated with the PHY
device and controlled by the PHY driver. I am wary of regressions though,
which is why I wanted the commit message to clearly spell out the implications.

> I will clarify the commit msg with this in mind.

Thanks.

> [1] https://lore.kernel.org/lkml/20250709133222.48802-4-buday.csaba@prolan.hu/

Is this mainline yet?

Cheers,
Ahmad

> 
>>>
>>> Co-developed-by: Csaba Buday <buday.csaba at prolan.hu>
>>> Signed-off-by: Csaba Buday <buday.csaba at prolan.hu>lan8710 reset
>>> Signed-off-by: Bence Csókás <csokas.bence at prolan.hu>
>>> ---
>>>   arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi | 8 +++++++-
>>>   1 file changed, 7 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
>>> index f053358bc9317f8447d65013a18670cb470106b2..0a5e90704ea481b0716d6ff6bc6d2110914d4f31 100644
>>> --- a/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
>>> +++ b/arch/arm/boot/dts/nxp/imx/imx6ul-tx6ul.dtsi
>>> @@ -246,7 +246,6 @@ &fec1 {
>>>       pinctrl-names = "default";
>>>       pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio &pinctrl_etnphy0_rst>;
>>>       phy-mode = "rmii";
>>> -    phy-reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
>>>       phy-supply = <&reg_3v3_etn>;
>>>       phy-handle = <&etnphy0>;
>>>       status = "okay";
>>> @@ -262,6 +261,13 @@ etnphy0: ethernet-phy at 0 {
>>>               pinctrl-0 = <&pinctrl_etnphy0_int>;
>>>               interrupt-parent = <&gpio5>;
>>>               interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
>>> +            /* Reset SHOULD be a PHY property */
>>
>> Comment belongs into commit message.
> 
> Agreed.
> 
>>> +            reset-names = "phy";
>>> +            reset-gpios = <&gpio5 6 GPIO_ACTIVE_LOW>;
>>> +            reset-assert-us = <100>;
>>> +            reset-deassert-us = <25000>;
>>> +            /* Energy detect sometimes causes link failures */
>>> +            smsc,disable-energy-detect;
>>
>> Unrelated change not described in the commit message.
> 
> Oh, this has accidentally made it into here from our DT. Thanks for spotting it!
> 
>> Cheers,
>> Ahmad
>>
>>>               status = "okay";
>>>           };
>>>  
>>> ---
>>> base-commit: 0cc53520e68bea7fb80fdc6bdf8d226d1b6a98d9
>>> change-id: 20250815-b4-tx6ul-dt-phy-rst-7afc190a6907
>>>
>>> Best regards,
>>
>>
> 
> Bence
> 
> 


-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |