[PATCH v4 1/3] dt-bindings: pinctrl: Add support for Broadcom STB pin controller

[Rob Herring]

On Thu, Aug 28, 2025 at 02:47:38PM +0200, Andrea della Porta wrote:
> From: "Ivan T. Ivanov" <iivanov at suse.de>
> 
> The STB pin controller represents a family whose silicon instances
> are found e.g. on BCM2712 SoC.
> 
> In particular, on RaspberryPi 5, there are two separate instantiations
> of the same IP block which differ in the number of pins that are
> associated and the pinmux functions for each of those pins. The
> -aon- variant stands for 'Always On'.
> 
> Depending on the revision of the BCM2712 (CO or D0), the pin
> controller instance has slight differences in the register layout.
> 
> Signed-off-by: Ivan T. Ivanov <iivanov at suse.de>
> Signed-off-by: Andrea della Porta <andrea.porta at suse.com>
> ---
>  .../pinctrl/brcm,bcm2712c0-pinctrl.yaml       | 137 ++++++++++++++++++
>  1 file changed, 137 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/brcm,bcm2712c0-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2712c0-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2712c0-pinctrl.yaml
> new file mode 100644
> index 000000000000..1e5d5234ee8d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2712c0-pinctrl.yaml
> @@ -0,0 +1,137 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/brcm,bcm2712c0-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Broadcom STB family pin controller
> +
> +maintainers:
> +  - Ivan T. Ivanov <iivanov at suse.de>
> +  - A. della Porta <andrea.porta at suse.com>
> +
> +description: >
> +  Broadcom's STB family of memory-mapped pin controllers.
> +
> +  This includes the pin controllers inside the BCM2712 SoC which
> +  are instances of the STB family and has two silicon variants,
> +  C0 and D0, which differs slightly in terms of registers layout.
> +
> +  The -aon- (Always On) variant is the same IP block but differs
> +  in the number of pins that are associated and the pinmux functions
> +  for each of those pins.
> +
> +allOf:
> +  - $ref: pinctrl.yaml#
> +
> +properties:
> +  compatible:
> +    enum:
> +      - brcm,bcm2712c0-pinctrl
> +      - brcm,bcm2712c0-aon-pinctrl
> +      - brcm,bcm2712d0-pinctrl
> +      - brcm,bcm2712d0-aon-pinctrl
> +
> +  reg:
> +    maxItems: 1
> +
> +patternProperties:
> +  '-state$':
> +    oneOf:
> +      - $ref: '#/$defs/brcmstb-pinctrl-state'
> +      - patternProperties:
> +          '-pins$':
> +            $ref: '#/$defs/brcmstb-pinctrl-state'
> +        additionalProperties: false
> +
> +$defs:
> +  brcmstb-pinctrl-state:
> +    allOf:
> +      - $ref: pincfg-node.yaml#
> +      - $ref: pinmux-node.yaml#
> +
> +    description: >
> +      Pin controller client devices use pin configuration subnodes (children
> +      and grandchildren) for desired pin configuration.
> +
> +      Client device subnodes use below standard properties.
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode (either this or "groups" must be specified).
> +        items:
> +          pattern: '^((aon_)?s?gpio[0-6]?[0-9])|(emmc_(clk|cmd|dat[0-7]|ds))$'
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +        enum: [ gpio, alt1, alt2, alt3, alt4, alt5, alt6, alt7, alt8,
> +                aon_cpu_standbyb, aon_fp_4sec_resetb, aon_gpclk, aon_pwm,
> +                arm_jtag, aud_fs_clk0, avs_pmu_bsc, bsc_m0, bsc_m1, bsc_m2,
> +                bsc_m3, clk_observe, ctl_hdmi_5v, enet0, enet0_mii, enet0_rgmii,
> +                ext_sc_clk, fl0, fl1, gpclk0, gpclk1, gpclk2, hdmi_tx0_auto_i2c,
> +                hdmi_tx0_bsc, hdmi_tx1_auto_i2c, hdmi_tx1_bsc, i2s_in, i2s_out,
> +                ir_in, mtsif, mtsif_alt, mtsif_alt1, pdm, pkt, pm_led_out, sc0,
> +                sd0, sd2, sd_card_a, sd_card_b, sd_card_c, sd_card_d, sd_card_e,
> +                sd_card_f, sd_card_g, spdif_out, spi_m, spi_s, sr_edm_sense, te0,
> +                te1, tsio, uart0, uart1, uart2, usb_pwr, usb_vbus, uui, vc_i2c0,
> +                vc_i2c3, vc_i2c4, vc_i2c5, vc_i2csl, vc_pcm, vc_pwm0, vc_pwm1,
> +                vc_spi0, vc_spi3, vc_spi4, vc_spi5, vc_uart0, vc_uart2, vc_uart3,
> +                vc_uart4 ]
> +
> +      bias-disable: true
> +      bias-pull-down: true
> +      bias-pull-up: true
> +
> +    required:
> +      - pins
> +
> +    if:
> +      properties:
> +        pins:
> +          not:
> +            contains:
> +              pattern: "^emmc_(clk|cmd|dat[0-7]|ds)$"
> +    then:
> +      required:
> +        - function
> +    else:
> +      properties:
> +        function: false
> +
> +    additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    brcm_pinctrl: pinctrl at 7d504100 {

Drop unused label.

> +        compatible = "brcm,bcm2712c0-pinctrl";
> +        reg = <0x7d504100 0x30>;
> +
> +        bt-shutdown-default-state {
> +           function = "gpio";
> +           pins = "gpio29";

Wrong indentation. With those fixed,

Reviewed-by: Rob Herring (Arm) <robh at kernel.org>

> +        };
> +
> +        uarta-default-state {
> +            rts-tx-pins {
> +                function = "uart0";
> +                pins = "gpio24", "gpio26";
> +                bias-disable;
> +            };
> +
> +            cts-rx-pins {
> +                function = "uart0";
> +                pins = "gpio25", "gpio27";
> +                bias-pull-up;
> +            };
> +        };
> +    };
> -- 
> 2.35.3
>