[PATCH] arm64: dts: imx95-19x19-evk: correct the phy setting for flexcan1/2

[Frank Li]

On Tue, Aug 19, 2025 at 10:43:37AM +0800, Haibo Chen wrote:
> 1, the phy support up to 8Mbit/s databitrate for CAN FD.
>    refer to product data sheet:
>      https://www.nxp.com/docs/en/data-sheet/TJA1463.pdf
> 2, the standby pin of the phy is ACTIVE_LOW.
> 3, the phy of flexcan2 connect the standby/en pin to PCAL6408 on i2c4 bus.
>
> Fixes: 02b7adb791e1 ("arm64: dts: imx95-19x19-evk: add adc0 flexcan[1,2] i2c[2,3] uart5 spi3 and tpm3")
> Signed-off-by: Haibo Chen <haibo.chen at nxp.com>
> ---
>  arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts | 10 +++++-----
>  1 file changed, 5 insertions(+), 5 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> index 2f949a0d48d2d8066388884703c3b3cd678f16e1..9d034275c847606919af8ee4a80a00599abf4d8b 100644
> --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> @@ -80,17 +80,17 @@ linux_cma: linux,cma {
>  	flexcan1_phy: can-phy0 {
>  		compatible = "nxp,tjr1443";
>  		#phy-cells = <0>;
> -		max-bitrate = <1000000>;
> +		max-bitrate = <8000000>;
>  		enable-gpios = <&i2c6_pcal6416 6 GPIO_ACTIVE_HIGH>;
> -		standby-gpios = <&i2c6_pcal6416 5 GPIO_ACTIVE_HIGH>;
> +		standby-gpios = <&i2c6_pcal6416 5 GPIO_ACTIVE_LOW>;

It use go though CAN phy.

Frank
>  	};
>
>  	flexcan2_phy: can-phy1 {
>  		compatible = "nxp,tjr1443";
>  		#phy-cells = <0>;
> -		max-bitrate = <1000000>;
> -		enable-gpios = <&i2c6_pcal6416 4 GPIO_ACTIVE_HIGH>;
> -		standby-gpios = <&i2c6_pcal6416 3 GPIO_ACTIVE_HIGH>;
> +		max-bitrate = <8000000>;
> +		enable-gpios = <&i2c4_gpio_expander_21 4 GPIO_ACTIVE_HIGH>;
> +		standby-gpios = <&i2c4_gpio_expander_21 3 GPIO_ACTIVE_LOW>;
>  	};
>
>  	reg_vref_1v8: regulator-1p8v {
>
> ---
> base-commit: 3ac864c2d9bb8608ee236e89bf561811613abfce
> change-id: 20250819-can-dts-fix-62ac1d02c007
>
> Best regards,
> --
> Haibo Chen <haibo.chen at nxp.com>
>