[PATCH v5 14/16] media: uapi: Add parameters structs to mali-c55-config.h
Daniel Scally
dan.scally at ideasonboard.com
Wed May 29 08:28:56 PDT 2024
Add structures describing the ISP parameters to mali-c55-config.h
Acked-by: Nayden Kanchev <nayden.kanchev at arm.com>
Co-developed-by: Jacopo Mondi <jacopo.mondi at ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi at ideasonboard.com>
Signed-off-by: Daniel Scally <dan.scally at ideasonboard.com>
---
Changes in v5:
- New patch
.../uapi/linux/media/arm/mali-c55-config.h | 669 ++++++++++++++++++
1 file changed, 669 insertions(+)
diff --git a/include/uapi/linux/media/arm/mali-c55-config.h b/include/uapi/linux/media/arm/mali-c55-config.h
index 8fb89af6c874..fce14bc74f4a 100644
--- a/include/uapi/linux/media/arm/mali-c55-config.h
+++ b/include/uapi/linux/media/arm/mali-c55-config.h
@@ -179,4 +179,673 @@ struct mali_c55_stats_buffer {
__u32 reserved3[15];
} __attribute__((packed));
+/**
+ * enum mali_c55_param_buffer_version - Mali-C55 parameters block versioning
+ *
+ * @MALI_C55_PARAM_BUFFER_V0: First version of Mali-C55 parameters block
+ */
+enum mali_c55_param_buffer_version {
+ MALI_C55_PARAM_BUFFER_V0,
+};
+
+/**
+ * enum mali_c55_param_block_type - Enumeration of Mali-C55 parameter blocks
+ *
+ * This enumeration defines the types of Mali-C55 parameters block. Each block
+ * configures a specific processing block of the Mali-C55 ISP. The block
+ * type allows the driver to correctly interpret the parameters block data.
+ *
+ * It is the responsibility of userspace to correctly set the type of each
+ * parameters block.
+ *
+ * @MALI_C55_PARAM_BLOCK_SENSOR_OFFS: Sensor pre-shading black level offset
+ * @MALI_C55_PARAM_BLOCK_AEXP_HIST: Auto-exposure 1024-bin histogram
+ * configuration
+ * @MALI_C55_PARAM_BLOCK_AEXP_IHIST: Post-Iridix auto-exposure 1024-bin
+ * histogram configuration
+ * @MALI_C55_PARAM_BLOCK_AEXP_HIST_WEIGHTS: Auto-exposure 1024-bin histogram
+ * weighting
+ * @MALI_C55_PARAM_BLOCK_AEXP_IHIST_WEIGHTS: Post-Iridix auto-exposure 1024-bin
+ * histogram weighting
+ * @MALI_C55_PARAM_BLOCK_DIGITAL_GAIN: Digital gain
+ * @MALI_C55_PARAM_BLOCK_AWB_GAINS: Auto-white balance gains
+ * @MALI_C55_PARAM_BLOCK_AWB_CONFIG: Auto-white balance statistics config
+ * @MALI_C55_PARAM_BLOCK_AWB_GAINS_AEXP: Auto-white balance gains for AEXP-0 tap
+ * @MALI_C55_PARAM_MESH_SHADING_CONFIG : Mesh shading tables configuration
+ * @MALI_C55_PARAM_MESH_SHADING_SELECTION: Mesh shading table selection
+ * @MALI_C55_PARAM_BLOCK_SENTINEL: First non-valid block index
+ */
+enum mali_c55_param_block_type {
+ MALI_C55_PARAM_BLOCK_SENSOR_OFFS,
+ MALI_C55_PARAM_BLOCK_AEXP_HIST,
+ MALI_C55_PARAM_BLOCK_AEXP_IHIST,
+ MALI_C55_PARAM_BLOCK_AEXP_HIST_WEIGHTS,
+ MALI_C55_PARAM_BLOCK_AEXP_IHIST_WEIGHTS,
+ MALI_C55_PARAM_BLOCK_DIGITAL_GAIN,
+ MALI_C55_PARAM_BLOCK_AWB_GAINS,
+ MALI_C55_PARAM_BLOCK_AWB_CONFIG,
+ MALI_C55_PARAM_BLOCK_AWB_GAINS_AEXP,
+ MALI_C55_PARAM_MESH_SHADING_CONFIG,
+ MALI_C55_PARAM_MESH_SHADING_SELECTION,
+ MALI_C55_PARAM_BLOCK_SENTINEL,
+};
+
+/**
+ * struct mali_c55_params_block_header - Mali-C55 parameter block header
+ *
+ * This structure represents the common part of all the ISP configuration
+ * blocks. Each parameters block shall embed an instance of this structure type
+ * as its first member, followed by the block-specific configuration data. The
+ * driver inspects this common header to discern the block type and its size and
+ * properly handle the block content by casting it to the correct block-specific
+ * type.
+ *
+ * The @type field is one of the values enumerated by
+ * :c:type:`mali_c55_param_block_type` and specifies how the data should be
+ * interpreted by the driver. The @size field specifies the size of the
+ * parameters block and is used by the driver for validation purposes. The
+ * @enabled field specifies if the ISP block should be enabled (and configured
+ * according to the provided parameters) or disabled.
+ *
+ * .. code-block:: c
+ *
+ * struct mali_c55_params_block_header *block = ...;
+ *
+ * switch (block->type) {
+ * case MALI_C55_PARAM_BLOCK_SENSOR_OFFS:
+ * struct mali_c55_params_sensor_off_preshading *sensor_offs =
+ * (struct mali_c55_params_sensor_off_preshading *)block;
+ *
+ * if (block->size !=
+ * sizeof(struct mali_c55_params_sensor_off_preshading))
+ * return -EINVAL;
+ *
+ * handle_sensor_offs(sensor_offs);
+ * break;
+ *
+ * case MALI_C55_PARAM_BLOCK_AEXP_HIST:
+ * struct mali_c55_params_aexp_hist *aexp_hist =
+ * (struct mali_c55_params_aexp_hist)block;
+ *
+ * if (block->size != sizeof(mali_c55_params_aexp_hist))
+ * return -EINVAL;
+ *
+ * handle_aexp_hist(aesp_hist);
+ * break;
+ *
+ * ...
+ *
+ * }
+ *
+ * Userspace is responsible for correctly populating the parameters block header
+ * fields (@type, @enabled and @size) and correctly populate the block-specific
+ * parameters.
+ *
+ * For example:
+ *
+ * .. code-block:: c
+ *
+ * void populate_sensor_offs(struct mali_c55_params_block_header *block) {
+ * block->type = MALI_C55_PARAM_BLOCK_SENSOR_OFFS;
+ * block->enabled = true;
+ * block->size = sizeof(struct mali_c55_params_sensor_off_preshading);
+ *
+ * struct mali_c55_params_sensor_off_preshading *sensor_offs =
+ * (struct mali_c55_params_sensor_off_preshading *)block;
+ *
+ * sensor_offs->chan00 = offset00;
+ * sensor_offs->chan01 = offset01;
+ * sensor_offs->chan10 = offset10;
+ * sensor_offs->chan11 = offset11;
+ * }
+ *
+ * @type: The parameters block type (enum mali_c55_param_block_type)
+ * @enabled: Block enabled/disabled flag
+ * @size: Size (in bytes) of the parameters block
+ */
+struct mali_c55_params_block_header {
+ enum mali_c55_param_block_type type;
+ bool enabled;
+ size_t size;
+};
+
+/**
+ * struct mali_c55_params_sensor_off_preshading - offset subtraction for each
+ * color channel
+ *
+ * Provides removal of the sensor black level from the sensor data. Separate
+ * offsets are provided for each of the four Bayer component color channels
+ * which are defaulted to R, Gr, Gb, B.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @chan00: Offset for color channel 00 (default: R)
+ * @chan01: Offset for color channel 01 (default: Gr)
+ * @chan10: Offset for color channel 10 (default: Gb)
+ * @chan11: Offset for color channel 11 (default: B)
+ */
+struct mali_c55_params_sensor_off_preshading {
+ struct mali_c55_params_block_header header;
+ __u32 chan00;
+ __u32 chan01;
+ __u32 chan10;
+ __u32 chan11;
+};
+
+/**
+ * enum mali_c55_aexp_hist_tap_points - Tap points for the AEXP histogram
+ * @MALI_C55_AEXP_HIST_TAP_WB: After static white balance
+ * @MALI_C55_AEXP_HIST_TAP_FS: After WDR Frame Stitch
+ * @MALI_C55_AEXP_HIST_TAP_TPG: After the test pattern generator
+ */
+enum mali_c55_aexp_hist_tap_points {
+ MALI_C55_AEXP_HIST_TAP_WB = 0,
+ MALI_C55_AEXP_HIST_TAP_FS,
+ MALI_C55_AEXP_HIST_TAP_TPG,
+};
+
+/**
+ * enum mali_c55_aexp_skip_x - Horizontal pixel skipping
+ * @MALI_C55_AEXP_SKIP_X_EVERY_2ND: Collect every 2nd pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_3RD: Collect every 3rd pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_4TH: Collect every 4th pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_5TH: Collect every 5th pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_8TH: Collect every 8th pixel horizontally
+ * @MALI_C55_AEXP_SKIP_X_EVERY_9TH: Collect every 9th pixel horizontally
+ */
+enum mali_c55_aexp_skip_x {
+ MALI_C55_AEXP_SKIP_X_EVERY_2ND,
+ MALI_C55_AEXP_SKIP_X_EVERY_3RD,
+ MALI_C55_AEXP_SKIP_X_EVERY_4TH,
+ MALI_C55_AEXP_SKIP_X_EVERY_5TH,
+ MALI_C55_AEXP_SKIP_X_EVERY_8TH,
+ MALI_C55_AEXP_SKIP_X_EVERY_9TH
+};
+
+/**
+ * enum mali_c55_aexp_skip_y - Vertical pixel skipping
+ * @MALI_C55_AEXP_SKIP_Y_ALL: Collect every single pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_2ND: Collect every 2nd pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_3RD: Collect every 3rd pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_4TH: Collect every 4th pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_5TH: Collect every 5th pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_8TH: Collect every 8th pixel vertically
+ * @MALI_C55_AEXP_SKIP_Y_EVERY_9TH: Collect every 9th pixel vertically
+ */
+enum mali_c55_aexp_skip_y {
+ MALI_C55_AEXP_SKIP_Y_ALL,
+ MALI_C55_AEXP_SKIP_Y_EVERY_2ND,
+ MALI_C55_AEXP_SKIP_Y_EVERY_3RD,
+ MALI_C55_AEXP_SKIP_Y_EVERY_4TH,
+ MALI_C55_AEXP_SKIP_Y_EVERY_5TH,
+ MALI_C55_AEXP_SKIP_Y_EVERY_8TH,
+ MALI_C55_AEXP_SKIP_Y_EVERY_9TH
+};
+
+/**
+ * enum mali_c55_aexp_row_column_offset - Start from the first or second row or
+ * column
+ * @MALI_C55_AEXP_FIRST_ROW_OR_COL: Start from the first row / column
+ * @MALI_C55_AEXP_SECOND_ROW_OR_COL: Start from the second row / column
+ */
+enum mali_c55_aexp_row_column_offset {
+ MALI_C55_AEXP_FIRST_ROW_OR_COL = 1,
+ MALI_C55_AEXP_SECOND_ROW_OR_COL = 2,
+};
+
+/**
+ * enum mali_c55_aexp_hist_plane_mode - Mode for the AEXP Histograms
+ * @MALI_C55_AEXP_HIST_COMBINED: All color planes in one 1024-bin histogram
+ * @MALI_C55_AEXP_HIST_SEPARATE: Each color plane in one 256-bin histogram with a bin width of 16
+ * @MALI_C55_AEXP_HIST_FOCUS_00: Top left plane in the first bank, rest in second bank
+ * @MALI_C55_AEXP_HIST_FOCUS_01: Top right plane in the first bank, rest in second bank
+ * @MALI_C55_AEXP_HIST_FOCUS_10: Bottom left plane in the first bank, rest in second bank
+ * @MALI_C55_AEXP_HIST_FOCUS_11: Bottom right plane in the first bank, rest in second bank
+ *
+ * In the "focus" modes statistics are collected into two 512-bin histograms
+ * with a bin width of 8. One colour plane is in the first histogram with the
+ * remainder combined into the second. The four options represent which of the
+ * four positions in a bayer pattern are the focused plane.
+ */
+enum mali_c55_aexp_hist_plane_mode {
+ MALI_C55_AEXP_HIST_COMBINED = 0,
+ MALI_C55_AEXP_HIST_SEPARATE = 1,
+ MALI_C55_AEXP_HIST_FOCUS_00 = 4,
+ MALI_C55_AEXP_HIST_FOCUS_01 = 5,
+ MALI_C55_AEXP_HIST_FOCUS_10 = 6,
+ MALI_C55_AEXP_HIST_FOCUS_11 = 7,
+};
+
+/**
+ * struct mali_c55_params_aexp_hist - configuration for AEXP metering hists
+ *
+ * This struct allows users to configure the 1024-bin AEXP histograms. Broadly
+ * speaking the parameters allow you to mask particular regions of the image and
+ * to select different kinds of histogram.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @skip_x: Horizontal decimation. See enum mali_c55_aexp_skip_x
+ * @offset_x: Column to start from. See enum mali_c55_aexp_row_column_offset
+ * @skip_y: Vertical decimation. See enum mali_c55_aexp_skip_y
+ * @offset_y: Row to start from. See enum mali_c55_aexp_row_column_offset
+ * @scale_bottom: scale of bottom half of range: 0=1x ,1=2x, 2=4x, 4=8x, 4=16x
+ * @scale_top: scale of top half of range: 0=1x ,1=2x, 2=4x, 4=8x, 4=16x
+ * @plane_mode: Plane separation mode. See enum mali_c55_aexp_hist_plane_mode
+ * @tap_point: Tap point for histogram from enum mali_c55_aexp_hist_tap_points.
+ * This parameter is unused for the post-Iridix Histogram
+ */
+struct mali_c55_params_aexp_hist {
+ struct mali_c55_params_block_header header;
+ __u8 skip_x;
+ __u8 offset_x;
+ __u8 skip_y;
+ __u8 offset_y;
+ __u8 scale_bottom;
+ __u8 scale_top;
+ __u8 plane_mode;
+ __u8 tap_point;
+};
+
+/**
+ * struct mali_c55_params_aexp_weights - Array of weights for AEXP metering
+ *
+ * This struct allows users to configure the weighting for both of the 1024-bin
+ * AEXP histograms. The pixel data collected for each zone is multiplied by the
+ * corresponding weight from this array, which may be zero if the intention is
+ * to mask off the zone entirely.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @nodes_used_horiz: Number of active zones horizontally [0..15]
+ * @nodes_used_vert: Number of active zones vertically [0..15]
+ * @zone_weights: Zone weighting. Index is row*col where 0,0 is the top
+ * left zone continuing in raster order. Each zone can be
+ * weighted in the range [0..15]. The number of rows and
+ * columns is defined by @nodes_used_vert and
+ * @nodes_used_horiz
+ */
+struct mali_c55_params_aexp_weights {
+ struct mali_c55_params_block_header header;
+ __u8 nodes_used_horiz;
+ __u8 nodes_used_vert;
+ __u8 zone_weights[MALI_C55_MAX_ZONES];
+};
+
+/**
+ * struct mali_c55_params_digital_gain - Digital gain value
+ *
+ * This struct carries a digital gain value to set in the ISP
+ *
+ * @header: The Mali-C55 parameters block header
+ * @gain: The digital gain value to apply, in Q5.8 format.
+ */
+struct mali_c55_params_digital_gain {
+ struct mali_c55_params_block_header header;
+ __u16 gain;
+};
+
+/**
+ * enum mali_c55_awb_stats_mode - Statistics mode for AWB
+ * @MALI_C55_AWB_MODE_GRBR: Statistics collected as Green/Red and Blue/Red ratios
+ * @MALI_C55_AWB_MODE_RGBG: Statistics collected as Red/Green and Blue/Green ratios
+ */
+enum mali_c55_awb_stats_mode {
+ MALI_C55_AWB_MODE_GRBR = 0,
+ MALI_C55_AWB_MODE_RGBG,
+};
+
+/**
+ * struct mali_c55_params_awb_gains - Gain settings for auto white balance
+ *
+ * This struct allows users to configure the gains for auto-white balance. There
+ * are four gain settings corresponding to each colour channel in the bayer
+ * domain. Although named generically, the association between the gain applied
+ * and the colour channel is done automatically within the ISP depending on the
+ * input format, and so the following mapping always holds true::
+ *
+ * gain00 = R
+ * gain01 = Gr
+ * gain10 = Gb
+ * gain11 = B
+ *
+ * All of the gains are stored in Q4.8 format.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @gain00: Multiplier for colour channel 00
+ * @gain01: Multiplier for colour channel 01
+ * @gain10: Multiplier for colour channel 10
+ * @gain11: Multiplier for colour channel 11
+ */
+struct mali_c55_params_awb_gains {
+ struct mali_c55_params_block_header header;
+ __u16 gain00;
+ __u16 gain01;
+ __u16 gain10;
+ __u16 gain11;
+};
+
+/**
+ * enum mali_c55_params_awb_tap_points - Tap points for the AWB statistics
+ * @MALI_C55_AWB_STATS_TAP_PF: Immediately after the Purple Fringe block
+ * @MALI_C55_AWB_STATS_TAP_CNR: Immediately after the CNR block
+ */
+enum mali_c55_params_awb_tap_points {
+ MALI_C55_AWB_STATS_TAP_PF = 0,
+ MALI_C55_AWB_STATS_TAP_CNR,
+};
+
+/**
+ * struct mali_c55_params_awb_config - Stats settings for auto-white balance
+ *
+ * This struct allows the configuration of the statistics generated for auto
+ * white balance. Pixel intensity limits can be set to exclude overly bright or
+ * dark regions of an image from the statistics entirely. Colour ratio minima
+ * and maxima can be set to discount pixels who's ratios fall outside the
+ * defined boundaries; there are two sets of registers to do this - the
+ * "min/max" ratios which bound a region and the "high/low" ratios which further
+ * trim the upper and lower ratios. For example with the boundaries configured
+ * as follows, only pixels whos colour ratios falls into the region marked "A"
+ * would be counted::
+ *
+ * cr_high
+ * 2.0 | |
+ * | cb_max --> _________________________v_____
+ * 1.8 | | \ |
+ * | | \ |
+ * 1.6 | | \ |
+ * | | \ |
+ * c 1.4 | cb_low -->|\ A \|<-- cb_high
+ * b | | \ |
+ * 1.2 | | \ |
+ * r | | \ |
+ * a 1.0 | cb_min --> |____\_________________________|
+ * t | ^ ^ ^
+ * i 0.8 | | | |
+ * o | cr_min | cr_max
+ * s 0.6 | |
+ * | cr_low
+ * 0.4 |
+ * |
+ * 0.2 |
+ * |
+ * 0.0 |_______________________________________________________________
+ * 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
+ * cr ratios
+ *
+ * @header: The Mali-C55 parameters block header
+ * @tap_point: The tap point from enum mali_c55_params_awb_tap_points
+ * @stats_mode: AWB statistics collection mode, see :c:type:`mali_c55_awb_stats_mode`
+ * @white_level: Upper pixel intensity (I.E. raw pixel values) limit
+ * @black_level: Lower pixel intensity (I.E. raw pixel values) limit
+ * @cr_max: Maximum R/G ratio (Q4.8 format)
+ * @cr_min: Minimum R/G ratio (Q4.8 format)
+ * @cb_max: Maximum B/G ratio (Q4.8 format)
+ * @cb_min: Minimum B/G ratio (Q4.8 format)
+ * @nodes_used_horiz: Number of active zones horizontally [0..15]
+ * @nodes_used_vert: Number of active zones vertically [0..15]
+ * @cr_high: R/G ratio trim high (Q4.8 format)
+ * @cr_low: R/G ratio trim low (Q4.8 format)
+ * @cb_high: B/G ratio trim high (Q4.8 format)
+ * @cb_low: B/G ratio trim low (Q4.8 format)
+ */
+struct mali_c55_params_awb_config {
+ struct mali_c55_params_block_header header;
+ __u8 tap_point;
+ __u8 stats_mode;
+ __u16 white_level;
+ __u16 black_level;
+ __u16 cr_max;
+ __u16 cr_min;
+ __u16 cb_max;
+ __u16 cb_min;
+ __u8 nodes_used_horiz;
+ __u8 nodes_used_vert;
+ __u16 cr_high;
+ __u16 cr_low;
+ __u16 cb_high;
+ __u16 cb_low;
+};
+
+#define MALI_C55_NUM_MESH_SHADING_ELEMENTS 3072
+
+/**
+ * struct mali_c55_params_mesh_shading_config - Mesh shading configuration
+ *
+ * The mesh shading correction module allows programming a separate table of
+ * either 16x16 or 32x32 node coefficients for 3 different light sources. The
+ * final correction coefficients applied are computed by blending the
+ * coefficients from two tables together.
+ *
+ * A page of 1024 32-bit integers is associated to each colour channel, with
+ * pages stored consecutively in memory. Each 32-bit integer packs 3 8-bit
+ * correction coefficients for a single node, one for each of the three light
+ * sources. The 8 most significant bits are unused. The following table
+ * describes the layout::
+ *
+ * +----------- Page (Colour Plane) 0 -------------+
+ * | @mesh[i] | Mesh Point | Bits | Light Source |
+ * +-----------+------------+-------+--------------+
+ * | 0 | 0,0 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ * | 1 | 0,1 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ * | ... | ... | ... | ... |
+ * +-----------+------------+-------+--------------+
+ * | 1023 | 31,31 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +----------- Page (Colour Plane) 1 -------------+
+ * | @mesh[i] | Mesh Point | Bits | Light Source |
+ * +-----------+------------+-------+--------------+
+ * | 1024 | 0,0 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ * | 1025 | 0,1 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ * | ... | ... | ... | ... |
+ * +-----------+------------+-------+--------------+
+ * | 2047 | 31,31 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +----------- Page (Colour Plane) 2 -------------+
+ * | @mesh[i] | Mesh Point | Bits | Light Source |
+ * +-----------+------------+-------+--------------+
+ * | 2048 | 0,0 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ * | 2049 | 0,1 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ * | ... | ... | ... | ... |
+ * +-----------+------------+-------+--------------+
+ * | 3071 | 31,31 | 16,23 | LS2 |
+ * | | | 08-15 | LS1 |
+ * | | | 00-07 | LS0 |
+ * +-----------+------------+-------+--------------+
+ *
+ * The @mesh_scale member determines the precision and minimum and maximum gain.
+ * For example if @mesh_scale is 0 and therefore selects 0 - 2x gain, a value of
+ * 0 in a coefficient means 0.0 gain, a value of 128 means 1.0 gain and 255
+ * means 2.0 gain.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @mesh_show: Output the mesh data rather than image data
+ * @mesh_scale: Set the precision and maximum gain range of mesh shading
+ * - 0 = 0-2x gain
+ * - 1 = 0-4x gain
+ * - 2 = 0-8x gain
+ * - 3 = 0-16x gain
+ * - 4 = 1-2x gain
+ * - 5 = 1-3x gain
+ * - 6 = 1-5x gain
+ * - 7 = 1-9x gain
+ * @mesh_page_r: Mesh page select for red colour plane [0..2]
+ * @mesh_page_g: Mesh page select for green colour plane [0..2]
+ * @mesh_page_b: Mesh page select for blue colour plane [0..2]
+ * @mesh_width: Number of horizontal nodes minus 1 [15,31]
+ * @mesh_height: Number of vertical nodes minus 1 [15,31]
+ * @mesh: Mesh shading correction tables
+ */
+struct mali_c55_params_mesh_shading_config {
+ struct mali_c55_params_block_header header;
+ bool mesh_show;
+ __u8 mesh_scale;
+ __u8 mesh_page_r;
+ __u8 mesh_page_g;
+ __u8 mesh_page_b;
+ __u8 mesh_width;
+ __u8 mesh_height;
+ __u32 mesh[MALI_C55_NUM_MESH_SHADING_ELEMENTS];
+};
+
+/** enum mali_c55_params_mesh_alpha_bank - Mesh shading table bank selection
+ * @MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS1 - Select Light Sources 0 and 1
+ * @MALI_C55_MESH_ALPHA_BANK_LS1_AND_LS2 - Select Light Sources 1 and 2
+ * @MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS2 - Select Light Sources 0 and 2
+ */
+enum mali_c55_params_mesh_alpha_bank {
+ MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS1 = 0,
+ MALI_C55_MESH_ALPHA_BANK_LS1_AND_LS2 = 1,
+ MALI_C55_MESH_ALPHA_BANK_LS0_AND_LS2 = 4
+};
+
+/**
+ * struct mali_c55_params_mesh_shading_selection - Mesh table selection
+ *
+ * The module computes the final correction coefficients by blending the ones
+ * from two light source tables, which are selected (independently for each
+ * colour channel) by the @mesh_alpha_bank_r/g/b fields.
+ *
+ * The final blended coefficients for each node are calculated using the
+ * following equation:
+ *
+ * Final coefficient = (a x LS\ :sub:`b`\ + (256 - a) x LS\ :sub:`a`\) / 256
+ *
+ * Where a is the @mesh_alpha_r/g/b value, and LS\ :sub:`a`\ and LS\ :sub:`b`\
+ * are the node cofficients for the two tables selected by the
+ * @mesh_alpha_bank_r/g/b value.
+ *
+ * The scale of the applied correction may also be controlled by tuning the
+ * @mesh_strength member. This is a modifier to the final coefficients which can
+ * be used to globally reduce the gains applied.
+ *
+ * @header: The Mali-C55 parameters block header
+ * @mesh_alpha_bank_r: Red mesh table select (c:type:`enum mali_c55_params_mesh_alpha_bank`)
+ * @mesh_alpha_bank_g: Green mesh table select (c:type:`enum mali_c55_params_mesh_alpha_bank`)
+ * @mesh_alpha_bank_b: Blue mesh table select (c:type:`enum mali_c55_params_mesh_alpha_bank`)
+ * @mesh_alpha_r: Blend coefficient for R [0..255]
+ * @mesh_alpha_g: Blend coefficient for G [0..255]
+ * @mesh_alpha_b: Blend coefficient for B [0..255]
+ * @mesh_strength: Mesh strength in Q4.12 format [0..4096]
+ */
+struct mali_c55_params_mesh_shading_selection {
+ struct mali_c55_params_block_header header;
+ __u8 mesh_alpha_bank_r;
+ __u8 mesh_alpha_bank_g;
+ __u8 mesh_alpha_bank_b;
+ __u8 mesh_alpha_r;
+ __u8 mesh_alpha_g;
+ __u8 mesh_alpha_b;
+ __u16 mesh_strength;
+};
+
+/**
+ * define MALI_C55_PARAMS_MAX_SIZE - Maximum size of all Mali C55 Parameters
+ *
+ * Though the parameters for the Mali-C55 are passed as optional blocks, the
+ * driver still needs to know the absolute maximum size so that it can allocate
+ * a buffer sized appropriately to accomodate userspace attempting to set all
+ * possible parameters in a single frame.
+ */
+#define MALI_C55_PARAMS_MAX_SIZE \
+ sizeof(struct mali_c55_params_sensor_off_preshading) + \
+ sizeof(struct mali_c55_params_aexp_hist) + \
+ sizeof(struct mali_c55_params_aexp_weights) + \
+ sizeof(struct mali_c55_params_aexp_hist) + \
+ sizeof(struct mali_c55_params_aexp_weights) + \
+ sizeof(struct mali_c55_params_digital_gain) + \
+ sizeof(struct mali_c55_params_awb_gains) + \
+ sizeof(struct mali_c55_params_awb_config) + \
+ sizeof(struct mali_c55_params_awb_gains) + \
+ sizeof(struct mali_c55_params_mesh_shading_config) + \
+ sizeof(struct mali_c55_params_mesh_shading_selection)
+
+/**
+ * struct mali_c55_params_buffer - 3A configuration parameters
+ *
+ * This struct contains the configuration parameters of the Mali-C55 ISP
+ * algorithms, serialized by userspace into an opaque data buffer. Each
+ * configuration parameter block is represented by a block-specific structure
+ * which contains a :c:type:`mali_c55_params_block_header` entry as first
+ * member. Userspace populates the @data buffer with configuration parameters
+ * for the blocks that it intends to configure. As a consequence, the data
+ * buffer effective size changes according to the number of ISP blocks that
+ * userspace intends to configure.
+ *
+ * The parameters buffer is versioned by the @version field to allow modifying
+ * and extending its definition. Userspace should populate the @version field to
+ * inform the driver about the version it intends to use. The driver will parse
+ * and handle the @data buffer according to the data layout specific to the
+ * indicated revision and return an error if the desired revision is not
+ * supported.
+ *
+ * For each ISP block that userspace wants to configure, a block-specific
+ * structure is appended to the @data buffer, one after the other without gaps
+ * in between nor overlaps. Userspace shall populate the @total_size field with
+ * the effective size, in bytes, of the @data buffer.
+ *
+ * The expected memory layout of the parameters buffer is::
+ *
+ * +-------------------- struct mali_c55_params_buffer ------------------+
+ * | version = MALI_C55_PARAM_BUFFER_V0; |
+ * | total_size = sizeof(struct mali_c55_params_sensor_off_preshading) |
+ * | sizeof(struct mali_c55_params_aexp_hist); |
+ * | +------------------------- data ---------------------------------+ |
+ * | | +--------- struct mali_c55_params_sensor_off_preshading ------+ | |
+ * | | | +-------- struct mali_c55_params_block_header header -----+ | | |
+ * | | | | type = MALI_C55_PARAM_BLOCK_SENSOR_OFFS; | | | |
+ * | | | | enabled = 1; | | | |
+ * | | | | size = | | | |
+ * | | | | sizeof(struct mali_c55_params_sensor_off_preshading);| | | |
+ * | | | +---------------------------------------------------------+ | | |
+ * | | | chan00 = ...; | | |
+ * | | | chan01 = ...; | | |
+ * | | | chan10 = ...; | | |
+ * | | | chan11 = ...; | | |
+ * | | +------------ struct mali_c55_params_aexp_hist ---------------+ | |
+ * | | | +-------- struct mali_c55_params_block_header header -----+ | | |
+ * | | | | type = MALI_C55_PARAM_BLOCK_AEXP_HIST; | | | |
+ * | | | | enabled = 1; | | | |
+ * | | | | size = sizeof(struct mali_c55_params_aexp_hist); | | | |
+ * | | | +---------------------------------------------------------+ | | |
+ * | | | skip_x = ...; | | |
+ * | | | offset_x = ...; | | |
+ * | | | skip_y = ...; | | |
+ * | | | offset_y = ...; | | |
+ * | | | scale_bottom = ...; | | |
+ * | | | scale_top = ...; | | |
+ * | | | plane_mode = ...; | | |
+ * | | | tap_point = ...; | | |
+ * | | +-------------------------------------------------------------+ | |
+ * | +-----------------------------------------------------------------+ |
+ * +---------------------------------------------------------------------+
+ *
+ * @version: The Mali-C55 parameters buffer version
+ * @total_size: The Mali-C55 configuration data effective size, excluding this
+ * header
+ * @data: The Mali-C55 configuration blocks data
+ */
+struct mali_c55_params_buffer {
+ enum mali_c55_param_buffer_version version;
+ size_t total_size;
+ __u8 data[MALI_C55_PARAMS_MAX_SIZE];
+};
+
#endif /* __UAPI_MALI_C55_CONFIG_H */
--
2.34.1
More information about the linux-arm-kernel
mailing list