[PATCH v6 1/2] dt-bindings: phy: Add i.MX8Q HSIO SerDes PHY binding

Frank Li Frank.li at nxp.com
Tue May 28 07:39:07 PDT 2024


On Tue, May 28, 2024 at 10:59:13AM +0800, Richard Zhu wrote:
> Add i.MX8QM and i.MX8QXP HSIO SerDes PHY binding.
> Introduce one HSIO configuration 'fsl,hsio-cfg', which need be set at
> initialization according to board design.
> 
> Signed-off-by: Richard Zhu <hongxing.zhu at nxp.com>
> ---
>  .../bindings/phy/fsl,imx8qm-hsio.yaml         | 164 ++++++++++++++++++
>  1 file changed, 164 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/fsl,imx8qm-hsio.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/fsl,imx8qm-hsio.yaml b/Documentation/devicetree/bindings/phy/fsl,imx8qm-hsio.yaml
> new file mode 100644
> index 000000000000..8af342ef3be3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/fsl,imx8qm-hsio.yaml
> @@ -0,0 +1,164 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/fsl,imx8qm-hsio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Freescale i.MX8QM SoC series High Speed IO(HSIO) SERDES PHY
> +
> +maintainers:
> +  - Richard Zhu <hongxing.zhu at nxp.com>
> +
> +properties:
> +  compatible:
> +    enum:
> +      - fsl,imx8qm-hsio
> +      - fsl,imx8qxp-hsio
> +  reg:
> +    items:
> +      - description: Base address and length of the PHY block
> +      - description: HSIO control and status registers(CSR) of the PHY
> +      - description: HSIO CSR of the controller bound to the PHY
> +      - description: HSIO CSR for MISC
> +
> +  reg-names:
> +    items:
> +      - const: reg
> +      - const: phy
> +      - const: ctrl
> +      - const: misc
> +
> +  "#phy-cells":
> +    const: 3
> +    description:
> +      The first defines lane index.
> +      The second defines the type of the PHY refer to the include phy.h.
> +      The third defines the controller index, indicated which controller
> +      is bound to the lane.
> +
> +  clocks:
> +    minItems: 5
> +    maxItems: 14
> +
> +  clock-names:
> +    minItems: 5
> +    maxItems: 14
> +
> +  fsl,hsio-cfg:
> +    description:

Here need "|" because you want keep format for below table.


> +      Specifies the use case of the HSIO module in the hardware design.
> +      Regarding the design of i.MX8QM HSIO subsystem, HSIO module can be
> +      confiured as following three use cases.
> +      +-------------------------------------+
> +      |                | i.MX8QM            |
> +      |----------------|--------------------|
> +      |                | Lane0| Lane1| Lane2|
> +      |----------------|------|------|------|
> +      | pcieax2sata    | PCIEA| PCIEA| SATA |
> +      |----------------|------|------|------|
> +      | pcieax2pcieb   | PCIEA| PCIEA| PCIEB|
> +      |----------------|------|------|------|
> +      | pcieapciebsata | PCIEA| PCIEB| SATA |
> +      +-------------------------------------+
> +    $ref: /schemas/types.yaml#/definitions/string
> +    enum: [ pcieax2sata, pcieax2pcieb, pcieapciebsata]

how about:
	pciea-x2-sata, pciea-x2-pcieb, pciea-pcieb-sata

> +    default: pcieapciebsata
> +
> +  fsl,refclk-pad-mode:
> +    description:
> +      Specifies the mode of the refclk pad used. INPUT(PHY refclock is
> +      provided externally via the refclk pad) or OUTPUT(PHY refclock is
> +      derived from SoC internal source and provided on the refclk pad).
> +      This property not exists means unused(PHY refclock is derived from
> +      SoC internal source).
> +    $ref: /schemas/types.yaml#/definitions/string
> +    enum: [ input, output, unused ]
> +    default: unused
> +
> +  power-domains:
> +    minItems: 1
> +    maxItems: 2
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - "#phy-cells"
> +  - clocks
> +  - clock-names
> +  - fsl,hsio-cfg
> +
> +allOf:
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - fsl,imx8qxp-hsio
> +    then:
> +      properties:
> +        clock-names:
> +          items:
> +            - const: pclk0
> +            - const: apb_pclk0
> +            - const: phy0_crr
> +            - const: ctl0_crr
> +            - const: misc_crr
> +        power-domains:
> +          maxItems: 1
> +
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - fsl,imx8qm-hsio
> +    then:
> +      properties:
> +        clock-names:
> +          items:
> +            - const: pclk0
> +            - const: pclk1
> +            - const: apb_pclk0
> +            - const: apb_pclk1
> +            - const: pclk2
> +            - const: epcs_tx
> +            - const: epcs_rx
> +            - const: apb_pclk2
> +            - const: phy0_crr
> +            - const: phy1_crr
> +            - const: ctl0_crr
> +            - const: ctl1_crr
> +            - const: ctl2_crr
> +            - const: misc_crr
> +        power-domains:
> +          minItems: 2
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/imx8-clock.h>
> +    #include <dt-bindings/clock/imx8-lpcg.h>
> +    #include <dt-bindings/firmware/imx/rsrc.h>
> +    #include <dt-bindings/phy/phy-imx8-pcie.h>
> +
> +    phy at 5f1a0000 {
> +        compatible = "fsl,imx8qxp-hsio";
> +        reg = <0x5f1a0000 0x10000>,
> +              <0x5f120000 0x10000>,
> +              <0x5f140000 0x10000>,
> +              <0x5f160000 0x10000>;
> +        reg-names = "reg", "phy", "ctrl", "misc";
> +        clocks = <&phyx1_lpcg IMX_LPCG_CLK_0>,
> +                 <&phyx1_lpcg IMX_LPCG_CLK_4>,
> +                 <&phyx1_crr1_lpcg IMX_LPCG_CLK_4>,
> +                 <&pcieb_crr3_lpcg IMX_LPCG_CLK_4>,
> +                 <&misc_crr5_lpcg IMX_LPCG_CLK_4>;
> +        clock-names = "pclk0", "apb_pclk0", "phy0_crr", "ctl0_crr", "misc_crr";
> +        power-domains = <&pd IMX_SC_R_SERDES_1>;
> +        #phy-cells = <3>;
> +        fsl,hsio-cfg = "pcieapciebsata";
> +        fsl,refclk-pad-mode = "input";
> +    };
> +...
> -- 
> 2.37.1
> 



More information about the linux-arm-kernel mailing list