[PATCH v3 1/2] PM / devfreq: exynos: Use Use devm_clk_get_enabled() helpers

Chanwoo Choi chanwoo at kernel.org
Wed May 8 08:45:30 PDT 2024


On Wed, Apr 17, 2024 at 1:45 PM Anand Moon <linux.amoon at gmail.com> wrote:
>
> The devm_clk_get_enabled() helpers:
>     - call devm_clk_get()
>     - call clk_prepare_enable() and register what is needed in order to
>      call clk_disable_unprepare() when needed, as a managed resource.
>
> This simplifies the code and avoids the calls to clk_disable_unprepare().
>
> While at it, use dev_err_probe consistently, and use its return value
> to return the error code.
>
> Signed-off-by: Anand Moon <linux.amoon at gmail.com>
> ---
> v3 - No change
> v2 - No change
> ---
>  drivers/devfreq/exynos-bus.c | 21 ++++-----------------
>  1 file changed, 4 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c
> index 245898f1a88e..153340b6685f 100644
> --- a/drivers/devfreq/exynos-bus.c
> +++ b/drivers/devfreq/exynos-bus.c
> @@ -160,7 +160,6 @@ static void exynos_bus_exit(struct device *dev)
>         platform_device_unregister(bus->icc_pdev);
>
>         dev_pm_opp_of_remove_table(dev);
> -       clk_disable_unprepare(bus->clk);
>         dev_pm_opp_put_regulators(bus->opp_token);
>  }
>
> @@ -171,7 +170,6 @@ static void exynos_bus_passive_exit(struct device *dev)
>         platform_device_unregister(bus->icc_pdev);
>
>         dev_pm_opp_of_remove_table(dev);
> -       clk_disable_unprepare(bus->clk);
>  }
>
>  static int exynos_bus_parent_parse_of(struct device_node *np,
> @@ -247,23 +245,15 @@ static int exynos_bus_parse_of(struct device_node *np,
>         int ret;
>
>         /* Get the clock to provide each bus with source clock */
> -       bus->clk = devm_clk_get(dev, "bus");
> -       if (IS_ERR(bus->clk)) {
> -               dev_err(dev, "failed to get bus clock\n");
> -               return PTR_ERR(bus->clk);
> -       }
> -
> -       ret = clk_prepare_enable(bus->clk);
> -       if (ret < 0) {
> -               dev_err(dev, "failed to get enable clock\n");
> -               return ret;
> -       }
> +       bus->clk = devm_clk_get_enabled(dev, "bus");
> +       if (IS_ERR(bus->clk))
> +               return dev_err_probe(dev, PTR_ERR(bus->clk), "failed to get bus clock\n");

nitpick. I recommend that better to keep 80 char on one line as following
for the readability.

               return dev_err_probe(dev, PTR_ERR(bus->clk),
                                          "failed to get bus clock\n");


>
>         /* Get the freq and voltage from OPP table to scale the bus freq */
>         ret = dev_pm_opp_of_add_table(dev);
>         if (ret < 0) {
>                 dev_err(dev, "failed to get OPP table\n");
> -               goto err_clk;
> +               return ret;
>         }
>
>         rate = clk_get_rate(bus->clk);
> @@ -281,8 +271,6 @@ static int exynos_bus_parse_of(struct device_node *np,
>
>  err_opp:
>         dev_pm_opp_of_remove_table(dev);
> -err_clk:
> -       clk_disable_unprepare(bus->clk);
>
>         return ret;
>  }
> @@ -453,7 +441,6 @@ static int exynos_bus_probe(struct platform_device *pdev)
>
>  err:
>         dev_pm_opp_of_remove_table(dev);
> -       clk_disable_unprepare(bus->clk);
>  err_reg:
>         dev_pm_opp_put_regulators(bus->opp_token);
>
> --
> 2.44.0
>
>


-- 
Best Regards,
Chanwoo Choi
Samsung Electronics



More information about the linux-arm-kernel mailing list