[PATCH v2] arm64: dts: imx8mp: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200

[Marek Vasut]

The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT to cater for this change.
Prototype rev.100 SoM was never publicly available and was manufactured in
limited series, anything currently available is rev.200 or newer, so it is
safe to update the DT this way.

Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: Andrew Lunn <andrew at lunn.ch>
Cc: Conor Dooley <conor+dt at kernel.org>
Cc: Fabio Estevam <festevam at gmail.com>
Cc: Krzysztof Kozlowski <krzk+dt at kernel.org>
Cc: Pengutronix Kernel Team <kernel at pengutronix.de>
Cc: Rob Herring <robh at kernel.org>
Cc: Sascha Hauer <s.hauer at pengutronix.de>
Cc: Shawn Guo <shawnguo at kernel.org>
Cc: devicetree at vger.kernel.org
Cc: imx at lists.linux.dev
Cc: kernel at dh-electronics.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: linux-kernel at vger.kernel.org
---
V2: Update the commit message, rev.100 SoM was a prototype that is not available
---
 arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
index 848df53c48685..4f7721a44daaa 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
@@ -110,14 +110,14 @@ mdio {
 		#size-cells = <0>;
 
 		/* Up to one of these two PHYs may be populated. */
-		ethphy0f: ethernet-phy at 0 { /* SMSC LAN8740Ai */
+		ethphy0f: ethernet-phy at 1 { /* SMSC LAN8740Ai */
 			compatible = "ethernet-phy-id0007.c110",
 				     "ethernet-phy-ieee802.3-c22";
 			interrupt-parent = <&gpio3>;
 			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-0 = <&pinctrl_ethphy0>;
 			pinctrl-names = "default";
-			reg = <0>;
+			reg = <1>;
 			reset-assert-us = <1000>;
 			reset-deassert-us = <1000>;
 			reset-gpios = <&ioexp 4 GPIO_ACTIVE_LOW>;
@@ -156,14 +156,14 @@ mdio {
 		#size-cells = <0>;
 
 		/* Up to one PHY may be populated. */
-		ethphy1f: ethernet-phy at 1 { /* SMSC LAN8740Ai */
+		ethphy1f: ethernet-phy at 2 { /* SMSC LAN8740Ai */
 			compatible = "ethernet-phy-id0007.c110",
 				     "ethernet-phy-ieee802.3-c22";
 			interrupt-parent = <&gpio4>;
 			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-0 = <&pinctrl_ethphy1>;
 			pinctrl-names = "default";
-			reg = <1>;
+			reg = <2>;
 			reset-assert-us = <1000>;
 			reset-deassert-us = <1000>;
 			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
-- 
2.43.0