[PATCH] arm64: dts: imx8mp: Update Fast ethernet PHY MDIO addresses to match DH i.MX8MP DHCOM rev.200

[Marek Vasut]

The production DH i.MX8MP DHCOM SoM rev.200 uses updated PHY MDIO addresses
for the Fast ethernet PHYs. Update the base SoM DT to cater for this change.

Signed-off-by: Marek Vasut <marex at denx.de>
---
Cc: Conor Dooley <conor+dt at kernel.org>
Cc: Fabio Estevam <festevam at gmail.com>
Cc: Krzysztof Kozlowski <krzk+dt at kernel.org>
Cc: Pengutronix Kernel Team <kernel at pengutronix.de>
Cc: Rob Herring <robh at kernel.org>
Cc: Sascha Hauer <s.hauer at pengutronix.de>
Cc: Shawn Guo <shawnguo at kernel.org>
Cc: devicetree at vger.kernel.org
Cc: imx at lists.linux.dev
Cc: kernel at dh-electronics.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: linux-kernel at vger.kernel.org
---
 arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
index 848df53c48685..4f7721a44daaa 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-dhcom-som.dtsi
@@ -110,14 +110,14 @@ mdio {
 		#size-cells = <0>;
 
 		/* Up to one of these two PHYs may be populated. */
-		ethphy0f: ethernet-phy at 0 { /* SMSC LAN8740Ai */
+		ethphy0f: ethernet-phy at 1 { /* SMSC LAN8740Ai */
 			compatible = "ethernet-phy-id0007.c110",
 				     "ethernet-phy-ieee802.3-c22";
 			interrupt-parent = <&gpio3>;
 			interrupts = <19 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-0 = <&pinctrl_ethphy0>;
 			pinctrl-names = "default";
-			reg = <0>;
+			reg = <1>;
 			reset-assert-us = <1000>;
 			reset-deassert-us = <1000>;
 			reset-gpios = <&ioexp 4 GPIO_ACTIVE_LOW>;
@@ -156,14 +156,14 @@ mdio {
 		#size-cells = <0>;
 
 		/* Up to one PHY may be populated. */
-		ethphy1f: ethernet-phy at 1 { /* SMSC LAN8740Ai */
+		ethphy1f: ethernet-phy at 2 { /* SMSC LAN8740Ai */
 			compatible = "ethernet-phy-id0007.c110",
 				     "ethernet-phy-ieee802.3-c22";
 			interrupt-parent = <&gpio4>;
 			interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 			pinctrl-0 = <&pinctrl_ethphy1>;
 			pinctrl-names = "default";
-			reg = <1>;
+			reg = <2>;
 			reset-assert-us = <1000>;
 			reset-deassert-us = <1000>;
 			reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
-- 
2.43.0