[PATCH 3/3] ARM: dts: sti: add thermal-zones support on stih418

[Patrice CHOTARD]

On 5/18/24 14:12, Raphael Gallais-Pou wrote:
> Add a 'thermal-zones' node for stih418.
> 
> A thermal-zone needs three components:
>   - thermal sensors, described in an earlier commit[1]
>   - cooling devices, specified for each CPU
>   - a thermal zone, describing the overall behavior.
> 
> The thermal zone needs references to both CPUs and thermal sensors,
> which phandle are also added. The thermal management will then be
> achieved on CPUs using the cpufreq framework.
> 
> [1] https://lore.kernel.org/lkml/20240320-thermal-v3-2-700296694c4a@gmail.com/
> 
> Signed-off-by: Raphael Gallais-Pou <rgallaispou at gmail.com>
> ---
>  arch/arm/boot/dts/st/stih407-family.dtsi |  6 +++--
>  arch/arm/boot/dts/st/stih418.dtsi        | 41 +++++++++++++++++++++++++++++---
>  2 files changed, 42 insertions(+), 5 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/st/stih407-family.dtsi b/arch/arm/boot/dts/st/stih407-family.dtsi
> index 29302e74aa1d..35a55aef7f4b 100644
> --- a/arch/arm/boot/dts/st/stih407-family.dtsi
> +++ b/arch/arm/boot/dts/st/stih407-family.dtsi
> @@ -33,7 +33,7 @@ delta_reserved: rproc at 44000000 {
>  	cpus {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		cpu at 0 {
> +		cpu0: cpu at 0 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a9";
>  			reg = <0>;
> @@ -52,8 +52,9 @@ cpu at 0 {
>  			clock-latency = <100000>;
>  			cpu0-supply = <&pwm_regulator>;
>  			st,syscfg = <&syscfg_core 0x8e0>;
> +			#cooling-cells = <2>;
>  		};
> -		cpu at 1 {
> +		cpu1: cpu at 1 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a9";
>  			reg = <1>;
> @@ -66,6 +67,7 @@ cpu at 1 {
>  					    1200000 0
>  					    800000  0
>  					    500000  0>;
> +			#cooling-cells = <2>;
>  		};
>  	};
>  
> diff --git a/arch/arm/boot/dts/st/stih418.dtsi b/arch/arm/boot/dts/st/stih418.dtsi
> index b35b9b7a7ccc..6622ffa8ecfa 100644
> --- a/arch/arm/boot/dts/st/stih418.dtsi
> +++ b/arch/arm/boot/dts/st/stih418.dtsi
> @@ -6,23 +6,26 @@
>  #include "stih418-clock.dtsi"
>  #include "stih407-family.dtsi"
>  #include "stih410-pinctrl.dtsi"
> +#include <dt-bindings/thermal/thermal.h>
>  / {
>  	cpus {
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		cpu at 2 {
> +		cpu2: cpu at 2 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a9";
>  			reg = <2>;
>  			/* u-boot puts hpen in SBC dmem at 0xa4 offset */
>  			cpu-release-addr = <0x94100A4>;
> +			#cooling-cells = <2>;
>  		};
> -		cpu at 3 {
> +		cpu3: cpu at 3 {
>  			device_type = "cpu";
>  			compatible = "arm,cortex-a9";
>  			reg = <3>;
>  			/* u-boot puts hpen in SBC dmem at 0xa4 offset */
>  			cpu-release-addr = <0x94100A4>;
> +			#cooling-cells = <2>;
>  		};
>  	};
>  
> @@ -44,6 +47,38 @@ usb2_picophy2: phy3 {
>  		reset-names = "global", "port";
>  	};
>  
> +	thermal-zones {
> +		cpu_thermal: cpu-thermal {
> +			polling-delay-passive = <250>;  /* 250ms */
> +			polling-delay = <1000>;         /* 1000ms */
> +
> +			thermal-sensors = <&thermal>;
> +
> +			trips {
> +				cpu_crit: cpu-crit {
> +					temperature = <95000>;  /* 95C */
> +					hysteresis = <2000>;
> +					type = "critical";
> +				};
> +				cpu_alert: cpu-alert {
> +					temperature = <85000>;  /* 85C */
> +					hysteresis = <2000>;
> +					type = "passive";
> +				};
> +			};
> +
> +			cooling-maps {
> +				map {
> +					trip = <&cpu_alert>;
> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> +							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +				};
> +			};
> +		};
> +	};
> +
>  	soc {
>  		rng11: rng at 8a8a000 {
>  			status = "disabled";
> @@ -107,7 +142,7 @@ mmc0: sdhci at 9060000 {
>  			assigned-clock-rates = <200000000>;
>  		};
>  
> -		thermal at 91a0000 {
> +		thermal: thermal at 91a0000 {
>  			compatible = "st,stih407-thermal";
>  			reg = <0x91a0000 0x28>;
>  			clock-names = "thermal";
> 

Hi Raphael

Reviewed-by: Patrice Chotard <patrice.chotard at foss.st.com>

Thanks
Patrice