[PATCH v2 0/8] Add R-Car fuse support

[Geert Uytterhoeven]

On Wed, May 29, 2024 at 11:29 AM Geert Uytterhoeven
<geert+renesas at glider.be> wrote:
> R-Car Gen3/Gen4 SoCs contain fuses indicating hardware support or
> hardware parameters.  Unfortunately the various SoCs require different
> mechanisms to read the state of the fuses:
>   - On R-Car Gen3, the fuse monitor registers are in the middle of the
>     Pin Function Controller (PFC) register block,
>   - On R-Car V3U and S4-8, the E-FUSE non-volatile memory is accessible
>     through a separate register block in the PFC,
>   - On R-Car V4H and V4M, the E-FUSE non-volatile memory is accessible
>     through the second register block of OTP_MEM.
>
> This patch series adds support for all 3 variants.  It provides an
> in-kernel API to read the fuses' states, as well as userspace access
> through the nvmem subsystem and sysfs:
>   - R-Car Gen3:    /sys/bus/platform/devices/rcar_fuse/fuse/nvmem
>   - R-Car V3U/S4:  /sys/bus/platform/devices/e6078800.fuse/fuse/nvmem
>   - R-Car V4H/V4M: /sys/bus/platform/devices/e61be000.otp/fuse/nvmem
>
> This has been tested on R-Car H3 ES2.0, M3-W and M3-W+, M3-N, V3M, V3H
> and V3H2, D3, E3, V3U, S4-8 ES1.0 and ES1.2, V4H, and V4M.
>
> For SoCs where E-FUSE is accessed through the PFC, it is not clear from
> the documentation if any PFC module clock needs to be enabled for fuse
> access.  According to experiments on R-Car S4-8, the module clock and
> reset only impact the GPIO functionality of the PFC, not the pinmux or
> fuse monitor functionalities.  So perhaps the clock/power-domains/resets
> properties should be dropped from the DT bindings and DTS, as well as
> the Runtime PM handling from the driver?
>
> Changes compared to v1[1]:
>   - Drop RFC state and broaden audience,
>   - Fix typo in one-line summary,
>   - Add Reviewed-by.
>
> Thanks for your comments!
>
> [1] https://lore.kernel.org/r/cover.1714642390.git.geert+renesas@glider.be
>
> Geert Uytterhoeven (8):
>   dt-bindings: fuse: Document R-Car E-FUSE / PFC
>   dt-bindings: fuse: Document R-Car E-FUSE / OTP_MEM
>   soc: renesas: Add R-Car fuse driver
>   pinctrl: renesas: Add R-Car Gen3 fuse support
>   arm64: dts: renesas: r8a779a0: Add E-FUSE node
>   arm64: dts: renesas: r8a779f0: Add E-FUSE node
>   arm64: dts: renesas: r8a779g0: Add OTP_MEM node
>   arm64: dts: renesas: r8a779h0: Add OTP_MEM node

I plan to queue these in renesas-devel/pinctrl for v6.11.

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds