[PATCH v5 10/12] ARM: dts: stm32: add ethernet1/2 RMII pins for STM32MP13F-DK board

[Christophe Roullier]

Those pins are used for Ethernet 1 and 2 on STM32MP13F-DK board.
ethernet1: RMII with crystal.
ethernet2: RMII without crystal.
Add analog gpio pin configuration ("sleep") to manage power mode on
stm32mp13.

Signed-off-by: Christophe Roullier <christophe.roullier at foss.st.com>
---
 arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi | 71 +++++++++++++++++++++
 1 file changed, 71 insertions(+)

diff --git a/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
index 32c5d8a1e06ac..7f72c62da0a64 100644
--- a/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
+++ b/arch/arm/boot/dts/st/stm32mp13-pinctrl.dtsi
@@ -13,6 +13,77 @@ pins {
 		};
 	};
 
+	eth1_rmii_pins_a: eth1-rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, AF11)>, /* ETH_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, AF11)>, /* ETH_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, AF11)>, /* ETH_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */
+				 <STM32_PINMUX('G', 2, AF11)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, AF11)>, /* ETH_RMII_RXD1 */
+				 <STM32_PINMUX('C', 1, AF10)>; /* ETH_RMII_CRS_DV */
+			bias-disable;
+		};
+
+	};
+
+	eth1_rmii_sleep_pins_a: eth1-rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RMII_TXD0 */
+				 <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RMII_TXD1 */
+				 <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RMII_TX_EN */
+				 <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RMII_REF_CLK */
+				 <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('G', 2, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RMII_RXD0 */
+				 <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RMII_RXD1 */
+				 <STM32_PINMUX('C', 1, ANALOG)>; /* ETH_RMII_CRS_DV */
+		};
+	};
+
+	eth2_rmii_pins_a: eth2-rmii-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, AF11)>, /* ETH_RMII_TXD0 */
+				 <STM32_PINMUX('G', 11, AF10)>, /* ETH_RMII_TXD1 */
+				 <STM32_PINMUX('G', 8, AF13)>, /* ETH_RMII_ETHCK */
+				 <STM32_PINMUX('F', 6, AF11)>, /* ETH_RMII_TX_EN */
+				 <STM32_PINMUX('B', 2, AF11)>, /* ETH_MDIO */
+				 <STM32_PINMUX('G', 5, AF10)>; /* ETH_MDC */
+			bias-disable;
+			drive-push-pull;
+			slew-rate = <1>;
+		};
+
+		pins2 {
+			pinmux = <STM32_PINMUX('F', 4, AF11)>, /* ETH_RMII_RXD0 */
+				 <STM32_PINMUX('E', 2, AF10)>, /* ETH_RMII_RXD1 */
+				 <STM32_PINMUX('A', 12, AF11)>; /* ETH_RMII_CRS_DV */
+			bias-disable;
+		};
+	};
+
+	eth2_rmii_sleep_pins_a: eth2-rmii-sleep-0 {
+		pins1 {
+			pinmux = <STM32_PINMUX('F', 7, ANALOG)>, /* ETH_RMII_TXD0 */
+				 <STM32_PINMUX('G', 11, ANALOG)>, /* ETH_RMII_TXD1 */
+				 <STM32_PINMUX('G', 8, ANALOG)>, /* ETH_RMII_ETHCK */
+				 <STM32_PINMUX('F', 6, ANALOG)>, /* ETH_RMII_TX_EN */
+				 <STM32_PINMUX('B', 2, ANALOG)>, /* ETH_MDIO */
+				 <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_MDC */
+				 <STM32_PINMUX('F', 4, ANALOG)>, /* ETH_RMII_RXD0 */
+				 <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RMII_RXD1 */
+				 <STM32_PINMUX('A', 12, ANALOG)>; /* ETH_RMII_CRS_DV */
+		};
+	};
+
 	i2c1_pins_a: i2c1-0 {
 		pins {
 			pinmux = <STM32_PINMUX('D', 12, AF5)>, /* I2C1_SCL */
-- 
2.25.1