[PATCH net-next v13 10/13] net: ethtool: pse-pd: Target the command to the requested PHY

[Maxime Chevallier]

PSE and PD configuration is a PHY-specific command. Instead of targeting
the command towards dev->phydev, use the request to pick the targeted
PHY device.

Signed-off-by: Maxime Chevallier <maxime.chevallier at bootlin.com>
Reviewed-by: Kory Maincent <kory.maincent at bootlin.com>
---
 net/ethtool/pse-pd.c | 16 ++++++----------
 1 file changed, 6 insertions(+), 10 deletions(-)

diff --git a/net/ethtool/pse-pd.c b/net/ethtool/pse-pd.c
index 2c981d443f27..3289a3631215 100644
--- a/net/ethtool/pse-pd.c
+++ b/net/ethtool/pse-pd.c
@@ -28,15 +28,13 @@ struct pse_reply_data {
 /* PSE_GET */
 
 const struct nla_policy ethnl_pse_get_policy[ETHTOOL_A_PSE_HEADER + 1] = {
-	[ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
+	[ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy_phy),
 };
 
-static int pse_get_pse_attributes(struct net_device *dev,
+static int pse_get_pse_attributes(struct phy_device *phydev,
 				  struct netlink_ext_ack *extack,
 				  struct pse_reply_data *data)
 {
-	struct phy_device *phydev = dev->phydev;
-
 	if (!phydev) {
 		NL_SET_ERR_MSG(extack, "No PHY is attached");
 		return -EOPNOTSUPP;
@@ -64,7 +62,7 @@ static int pse_prepare_data(const struct ethnl_req_info *req_base,
 	if (ret < 0)
 		return ret;
 
-	ret = pse_get_pse_attributes(dev, info->extack, data);
+	ret = pse_get_pse_attributes(req_base->phydev, info->extack, data);
 
 	ethnl_ops_complete(dev);
 
@@ -123,7 +121,7 @@ static int pse_fill_reply(struct sk_buff *skb,
 /* PSE_SET */
 
 const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1] = {
-	[ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy),
+	[ETHTOOL_A_PSE_HEADER] = NLA_POLICY_NESTED(ethnl_header_policy_phy),
 	[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL] =
 		NLA_POLICY_RANGE(NLA_U32, ETHTOOL_PODL_PSE_ADMIN_STATE_DISABLED,
 				 ETHTOOL_PODL_PSE_ADMIN_STATE_ENABLED),
@@ -135,11 +133,10 @@ const struct nla_policy ethnl_pse_set_policy[ETHTOOL_A_PSE_MAX + 1] = {
 static int
 ethnl_set_pse_validate(struct ethnl_req_info *req_info, struct genl_info *info)
 {
-	struct net_device *dev = req_info->dev;
 	struct nlattr **tb = info->attrs;
 	struct phy_device *phydev;
 
-	phydev = dev->phydev;
+	phydev = req_info->phydev;
 	if (!phydev) {
 		NL_SET_ERR_MSG(info->extack, "No PHY is attached");
 		return -EOPNOTSUPP;
@@ -171,12 +168,11 @@ ethnl_set_pse_validate(struct ethnl_req_info *req_info, struct genl_info *info)
 static int
 ethnl_set_pse(struct ethnl_req_info *req_info, struct genl_info *info)
 {
-	struct net_device *dev = req_info->dev;
 	struct pse_control_config config = {};
 	struct nlattr **tb = info->attrs;
 	struct phy_device *phydev;
 
-	phydev = dev->phydev;
+	phydev = req_info->phydev;
 	/* These values are already validated by the ethnl_pse_set_policy */
 	if (pse_has_podl(phydev->psec))
 		config.podl_admin_control = nla_get_u32(tb[ETHTOOL_A_PODL_PSE_ADMIN_CONTROL]);
-- 
2.45.1