[PATCH net-next v12 00/13] Introduce PHY listing and link_topology tracking

[Maxime Chevallier]

Hello everyone,

This is V12 for the link topology addition, allowing to track all PHYs
that are linked to netdevices.

This version is based on the V11 that was partially applied during last
cycle, then reverted as some issues were found by Nathan and Heiner, which lead
som some discussions to address them. Therefore, all issues that were reported
and the proposed fixes (thanks Heiner !) are taken into account, all of which
ended-up in patch 01/13.

The rest of the series is mostly untouched, the main points being an
update of the PSE-PD part following the PoE support added by Köry and
some fixes regarding the documentation (a broken ref found by Jakub).

I've gathered all of Andrew's reviews on V11, however as I had to rework
the pse-pd part a bit, I haven't added the tag on this patch (patch
10/13).

Discussions on the patch 01/13 updates can be found here :

https://lore.kernel.org/netdev/20240412104615.3779632-1-maxime.chevallier@bootlin.com/
https://lore.kernel.org/netdev/20240429131008.439231-1-maxime.chevallier@bootlin.com/
https://lore.kernel.org/netdev/20240507102822.2023826-1-maxime.chevallier@bootlin.com/

As a remainder, here's what the PHY listings would look like :
 - eth0 has a 88x3310 acting as media converter, and an SFP module with
   an embedded 88e1111 PHY
 - eth2 has a 88e1510 PHY

# ethtool --show-phys *

PHY for eth0:
PHY index: 1
Driver name: mv88x3310
PHY device name: f212a600.mdio-mii:00
Downstream SFP bus name: sfp-eth0
PHY id: 0
Upstream type: MAC

PHY for eth0:
PHY index: 2
Driver name: Marvell 88E1111
PHY device name: i2c:sfp-eth0:16
PHY id: 21040322
Upstream type: PHY
Upstream PHY index: 1
Upstream SFP name: sfp-eth0

PHY for eth2:
PHY index: 1
Driver name: Marvell 88E1510
PHY device name: f212a200.mdio-mii:00
PHY id: 21040593
Upstream type: MAC

Ethtool patches : https://github.com/minimaxwell/ethtool/tree/mc/main

Link to v11: https://lore.kernel.org/netdev/20240404093004.2552221-1-maxime.chevallier@bootlin.com/
Link to V10: https://lore.kernel.org/netdev/20240304151011.1610175-1-maxime.chevallier@bootlin.com/
Link to V9: https://lore.kernel.org/netdev/20240228114728.51861-1-maxime.chevallier@bootlin.com/
Link to V8: https://lore.kernel.org/netdev/20240220184217.3689988-1-maxime.chevallier@bootlin.com/
Link to V7: https://lore.kernel.org/netdev/20240213150431.1796171-1-maxime.chevallier@bootlin.com/
Link to V6: https://lore.kernel.org/netdev/20240126183851.2081418-1-maxime.chevallier@bootlin.com/
Link to V5: https://lore.kernel.org/netdev/20231221180047.1924733-1-maxime.chevallier@bootlin.com/
Link to V4: https://lore.kernel.org/netdev/20231215171237.1152563-1-maxime.chevallier@bootlin.com/
Link to V3: https://lore.kernel.org/netdev/20231201163704.1306431-1-maxime.chevallier@bootlin.com/
Link to V2: https://lore.kernel.org/netdev/20231117162323.626979-1-maxime.chevallier@bootlin.com/
Link to V1: https://lore.kernel.org/netdev/20230907092407.647139-1-maxime.chevallier@bootlin.com/


Maxime Chevallier (13):
  net: phy: Introduce ethernet link topology representation
  net: sfp: pass the phy_device when disconnecting an sfp module's PHY
  net: phy: add helpers to handle sfp phy connect/disconnect
  net: sfp: Add helper to return the SFP bus name
  net: ethtool: Allow passing a phy index for some commands
  netlink: specs: add phy-index as a header parameter
  net: ethtool: Introduce a command to list PHYs on an interface
  netlink: specs: add ethnl PHY_GET command set
  net: ethtool: plca: Target the command to the requested PHY
  net: ethtool: pse-pd: Target the command to the requested PHY
  net: ethtool: cable-test: Target the command to the requested PHY
  net: ethtool: strset: Allow querying phy stats by index
  Documentation: networking: document phy_link_topology

 Documentation/netlink/specs/ethtool.yaml      |  62 ++++
 Documentation/networking/ethtool-netlink.rst  |  52 +++
 Documentation/networking/index.rst            |   1 +
 .../networking/phy-link-topology.rst          | 121 +++++++
 MAINTAINERS                                   |   1 +
 drivers/net/phy/Makefile                      |   2 +-
 drivers/net/phy/marvell-88x2222.c             |   2 +
 drivers/net/phy/marvell.c                     |   2 +
 drivers/net/phy/marvell10g.c                  |   2 +
 drivers/net/phy/phy_device.c                  |  46 +++
 drivers/net/phy/phy_link_topology.c           | 105 ++++++
 drivers/net/phy/phylink.c                     |   3 +-
 drivers/net/phy/qcom/at803x.c                 |   2 +
 drivers/net/phy/qcom/qca807x.c                |   2 +
 drivers/net/phy/sfp-bus.c                     |  15 +-
 include/linux/netdevice.h                     |   4 +-
 include/linux/phy.h                           |   6 +
 include/linux/phy_link_topology.h             |  82 +++++
 include/linux/sfp.h                           |   8 +-
 include/uapi/linux/ethtool.h                  |  16 +
 include/uapi/linux/ethtool_netlink.h          |  21 ++
 net/core/dev.c                                |  15 +
 net/ethtool/Makefile                          |   2 +-
 net/ethtool/cabletest.c                       |  16 +-
 net/ethtool/netlink.c                         |  57 +++-
 net/ethtool/netlink.h                         |  10 +
 net/ethtool/phy.c                             | 306 ++++++++++++++++++
 net/ethtool/plca.c                            |  19 +-
 net/ethtool/pse-pd.c                          |  16 +-
 net/ethtool/strset.c                          |  17 +-
 30 files changed, 968 insertions(+), 45 deletions(-)
 create mode 100644 Documentation/networking/phy-link-topology.rst
 create mode 100644 drivers/net/phy/phy_link_topology.c
 create mode 100644 include/linux/phy_link_topology.h
 create mode 100644 net/ethtool/phy.c

-- 
2.45.1