[PATCH v6 6/7] arm64: dts: add description for solidrun cn9131 solidwan board
Josua Mayer
josua at solid-run.com
Sun Jun 2 08:49:41 PDT 2024
Add description for the SolidRun CN9131 SolidWAN, based on CN9130 SoM
with an extra communication processor on the carrier board.
This board differentiates itself from CN9130 Clearfog by providing
additional SoC native network interfaces and pci buses:
2x 10Gbps SFP+
4x 1Gbps RJ45
1x miniPCI-E
1x m.2 b-key with sata, usb-2.0 and usb-3.0
1x m.2 m-key with pcie and usb-2.0
1x m.2 b-key with pcie, usb-2.0, usb-3.0 and 2x sim slots
1x mpcie with pcie only
2x type-a usb-2.0/3.0
Signed-off-by: Josua Mayer <josua at solid-run.com>
---
arch/arm64/boot/dts/marvell/Makefile | 1 +
arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts | 637 +++++++++++++++++++++
2 files changed, 638 insertions(+)
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index 019f2251d696..16f9d7156d9f 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -30,3 +30,4 @@ dtb-$(CONFIG_ARCH_MVEBU) += ac5x-rd-carrier-cn9131.dtb
dtb-$(CONFIG_ARCH_MVEBU) += ac5-98dx35xx-rd.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-base.dtb
dtb-$(CONFIG_ARCH_MVEBU) += cn9130-cf-pro.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += cn9131-cf-solidwan.dtb
diff --git a/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts b/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts
new file mode 100644
index 000000000000..b1ea7dcaed17
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/cn9131-cf-solidwan.dts
@@ -0,0 +1,637 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Josua Mayer <josua at solid-run.com>
+ *
+ * DTS for SolidRun CN9130 Clearfog Base.
+ *
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+
+#include "cn9130.dtsi"
+#include "cn9130-sr-som.dtsi"
+
+/*
+ * Instantiate the external CP115
+ */
+
+#define CP11X_NAME cp1
+#define CP11X_BASE f4000000
+#define CP11X_PCIEx_MEM_BASE(iface) (0xe2000000 + (iface * 0x1000000))
+#define CP11X_PCIEx_MEM_SIZE(iface) 0xf00000
+#define CP11X_PCIE0_BASE f4600000
+#define CP11X_PCIE1_BASE f4620000
+#define CP11X_PCIE2_BASE f4640000
+
+#include "armada-cp115.dtsi"
+
+#undef CP11X_NAME
+#undef CP11X_BASE
+#undef CP11X_PCIEx_MEM_BASE
+#undef CP11X_PCIEx_MEM_SIZE
+#undef CP11X_PCIE0_BASE
+#undef CP11X_PCIE1_BASE
+#undef CP11X_PCIE2_BASE
+
+/ {
+ model = "SolidRun CN9131 SolidWAN";
+ compatible = "solidrun,cn9131-solidwan",
+ "solidrun,cn9130-sr-som", "marvell,cn9130";
+
+ aliases {
+ ethernet0 = &cp1_eth1;
+ ethernet1 = &cp1_eth2;
+ ethernet2 = &cp0_eth1;
+ ethernet3 = &cp0_eth2;
+ ethernet4 = &cp0_eth0;
+ ethernet5 = &cp1_eth0;
+ gpio0 = &ap_gpio;
+ gpio1 = &cp0_gpio1;
+ gpio2 = &cp0_gpio2;
+ gpio3 = &cp1_gpio1;
+ gpio4 = &cp1_gpio2;
+ gpio5 = &expander0;
+ i2c0 = &cp0_i2c0;
+ i2c1 = &cp0_i2c1;
+ i2c2 = &cp1_i2c1;
+ mmc0 = &ap_sdhci0;
+ mmc1 = &cp0_sdhci0;
+ rtc0 = &cp0_rtc;
+ rtc1 = &carrier_rtc;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&cp0_led_pins &cp1_led_pins>;
+
+ /* for sfp-1 (J42) */
+ led-sfp1-activity {
+ label = "sfp1:green";
+ gpios = <&cp0_gpio1 7 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* for sfp-1 (J42) */
+ led-sfp1-link {
+ label = "sfp1:yellow";
+ gpios = <&cp0_gpio1 4 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* (J28) */
+ led-sfp0-activity {
+ label = "sfp0:green";
+ gpios = <&cp1_gpio2 22 GPIO_ACTIVE_HIGH>;
+ };
+
+ /* (J28) */
+ led-sfp0-link {
+ label = "sfp0:yellow";
+ gpios = <&cp1_gpio2 23 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ /* Type-A port on J53 */
+ reg_usb_a_vbus0: regulator-usb-a-vbus0 {
+ compatible = "regulator-fixed";
+ pinctrl-0 = <&cp0_reg_usb_a_vbus0_pins>;
+ pinctrl-names = "default";
+ regulator-name = "vbus0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&cp0_gpio1 27 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ reg_usb_a_vbus1: regulator-usb-a-vbus1 {
+ compatible = "regulator-fixed";
+ pinctrl-0 = <&cp0_reg_usb_a_vbus1_pins>;
+ pinctrl-names = "default";
+ regulator-name = "vbus1";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpios = <&cp0_gpio1 28 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ };
+
+ sfp0: sfp-0 {
+ compatible = "sff,sfp";
+ pinctrl-0 = <&cp0_sfp0_pins>;
+ pinctrl-names = "default";
+ i2c-bus = <&cp0_i2c1>;
+ los-gpios = <&cp0_gpio2 2 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&cp0_gpio2 1 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cp0_gpio1 31 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <2000>;
+ };
+
+ sfp1: sfp-1 {
+ compatible = "sff,sfp";
+ pinctrl-0 = <&cp1_sfp1_pins>;
+ pinctrl-names = "default";
+ i2c-bus = <&cp1_i2c1>;
+ los-gpios = <&cp1_gpio2 2 GPIO_ACTIVE_HIGH>;
+ mod-def0-gpios = <&cp1_gpio2 18 GPIO_ACTIVE_LOW>;
+ tx-disable-gpios = <&cp1_gpio2 1 GPIO_ACTIVE_HIGH>;
+ tx-fault-gpios = <&cp1_gpio2 17 GPIO_ACTIVE_HIGH>;
+ maximum-power-milliwatt = <2000>;
+ };
+};
+
+&cp0_ethernet {
+ status = "okay";
+};
+
+/* SRDS #2 - SFP+ 10GE */
+&cp0_eth0 {
+ managed = "in-band-status";
+ phy-mode = "10gbase-r";
+ phys = <&cp0_comphy2 0>;
+ sfp = <&sfp0>;
+ status = "okay";
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp0_eth1 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ /* Without mdio phy access rely on sgmii auto-negotiation. */
+ phys = <&cp0_comphy3 1>;
+ status = "okay";
+};
+
+/* SRDS #1 - SGMII */
+&cp0_eth2 {
+ /delete-property/ pinctrl-0;
+ /delete-property/ pinctrl-names;
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ phy = <&cp0_phy1>;
+ phys = <&cp0_comphy1 2>;
+};
+
+&cp0_gpio1 {
+ pcie0-0-w-disable-hog {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie0.0-w-disable";
+ };
+
+ /* J34 */
+ m2-full-card-power-off-hog {
+ gpio-hog;
+ gpios = <8 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+};
+
+&cp0_i2c0 {
+ /* assembly option */
+ fan-controller at 18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ };
+
+ expander0: gpio at 41 {
+ compatible = "nxp,pca9536";
+ reg = <0x41>;
+
+ usb-a-vbus0-ilimit-hog {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "vbus0-ilimit";
+ };
+
+ /* duplicate connection, controlled by soc gpio */
+ usb-vbus0-enable-hog {
+ gpio-hog;
+ gpios = <1 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "vbus0-enable";
+ };
+
+ usb-a-vbus1-ilimit-hog {
+ gpio-hog;
+ gpios = <2 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "vbus1-ilimit";
+ };
+
+ /* duplicate connection, controlled by soc gpio */
+ usb-vbus1-enable-hog {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "vbus1-enable";
+ };
+ };
+
+ carrier_eeprom: eeprom at 52 {
+ compatible = "atmel,24c02";
+ reg = <0x52>;
+ pagesize = <8>;
+ };
+
+ /* usb-hub at 60 */
+
+ /* assembly option */
+ carrier_rtc: rtc at 68 {
+ compatible = "st,m41t83";
+ reg = <0x68>;
+ pinctrl-0 = <&cp1_rtc_pins>;
+ pinctrl-names = "default";
+ interrupt-parent = <&cp1_gpio1>;
+ interrupts = <12 IRQ_TYPE_EDGE_FALLING>;
+ reset-gpios = <&cp1_gpio1 13 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cp0_i2c1 {
+ /*
+ * Routed to SFP.
+ * Limit to 100kHz for compatibility with SFP modules,
+ * featuring AT24C01A/02/04 at addresses 0x50/0x51.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&cp0_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cp0_mdio {
+ /*
+ * SoM + Carrier each have a PHY at address 0.
+ * Remove the SoM phy node, and skip adding the carrier node.
+ * SGMII Auto-Negotation is enabled by bootloader for
+ * autonomous operation without mdio control.
+ */
+ /delete-node/ ethernet-phy at 0;
+
+ /* U17016 */
+ cp0_phy1: ethernet-phy at 1 {
+ reg = <1>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link is 1000Mbps: On (yellow)
+ * - LED[1]: link/activity: On/blink (green)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a17>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+/* SRDS #0 - miniPCIe */
+&cp0_pcie0 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy0 0>;
+ status = "okay";
+};
+
+/* SRDS #5 - M.2 B-Key (J34) */
+&cp0_pcie2 {
+ num-lanes = <1>;
+ phys = <&cp0_comphy5 2>;
+ status = "okay";
+};
+
+&cp0_pinctrl {
+ pinctrl-0 = <&cp0_m2_0_shutdown_pins &cp0_mpcie_rfkill_pins>;
+ pinctrl-names = "default";
+
+ cp0_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+
+ cp0_led_pins: cp0-led-pins {
+ marvell,pins = "mpp4", "mpp7";
+ marvell,function = "gpio";
+ };
+
+ cp0_m2_0_shutdown_pins: cp0-m2-0-shutdown-pins {
+ marvell,pins = "mpp8";
+ marvell,function = "gpio";
+ };
+
+ cp0_mmc0_pins: cp0-mmc0-pins {
+ marvell,pins = "mpp43", "mpp56", "mpp57", "mpp58",
+ "mpp59", "mpp60", "mpp61";
+ marvell,function = "sdio";
+ };
+
+ cp0_mpcie_rfkill_pins: cp0-mpcie-rfkill-pins {
+ marvell,pins = "mpp6";
+ marvell,function = "gpio";
+ };
+
+ cp0_reg_usb_a_vbus0_pins: cp0-reg-usb-a-vbus0-pins {
+ marvell,pins = "mpp27";
+ marvell,function = "gpio";
+ };
+
+ cp0_reg_usb_a_vbus1_pins: cp0-reg-usb-a-vbus1-pins {
+ marvell,pins = "mpp28";
+ marvell,function = "gpio";
+ };
+
+ cp0_sfp0_pins: cp0-sfp0-pins {
+ marvell,pins = "mpp31", "mpp32", "mpp33", "mpp34";
+ marvell,function = "gpio";
+ };
+
+ cp0_spi1_cs1_pins: cp0-spi1-cs1-pins {
+ marvell,pins = "mpp12";
+ marvell,function = "spi1";
+ };
+};
+
+/* microSD */
+&cp0_sdhci0 {
+ pinctrl-0 = <&cp0_mmc0_pins>;
+ pinctrl-names = "default";
+ bus-width = <4>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&cp0_spi1 {
+ /* add pin for chip-select 1 */
+ pinctrl-0 = <&cp0_spi1_pins &cp0_spi1_cs1_pins>;
+
+ flash at 1 {
+ compatible = "jedec,spi-nor";
+ reg = <1>;
+ /* read command supports max. 50MHz */
+ spi-max-frequency = <50000000>;
+ };
+};
+
+/* USB-2.0 Host to USB-Hub */
+&cp0_usb3_0 {
+ phys = <&cp0_utmi0>;
+ phy-names = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* SRDS #4 - USB-3.0 Host to USB-Hub */
+&cp0_usb3_1 {
+ phys = <&cp0_comphy4 1>, <&cp0_utmi1>;
+ phy-names = "comphy", "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&cp0_utmi {
+ status = "okay";
+};
+
+&cp0_utmi1 {
+ status = "disabled";
+};
+
+&cp1_ethernet {
+ status = "okay";
+};
+
+/* SRDS #4 - SFP+ 10GE */
+&cp1_eth0 {
+ managed = "in-band-status";
+ phy-mode = "10gbase-r";
+ phys = <&cp1_comphy4 0>;
+ sfp = <&sfp1>;
+ status = "okay";
+};
+
+/* SRDS #3 - SGMII 1GE */
+&cp1_eth1 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ phy = <&cp1_phy0>;
+ phys = <&cp0_comphy3 1>;
+ status = "okay";
+};
+
+/* SRDS #5 - SGMII 1GE */
+&cp1_eth2 {
+ managed = "in-band-status";
+ phy-mode = "sgmii";
+ phy = <&cp1_phy1>;
+ phys = <&cp0_comphy5 2>;
+ status = "okay";
+};
+
+&cp1_gpio1 {
+ status = "okay";
+
+ /* J30 */
+ m2-full-card-power-off-hog-0 {
+ gpio-hog;
+ gpios = <29 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+
+ /* J44 */
+ m2-full-card-power-off-hog-1 {
+ gpio-hog;
+ gpios = <30 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "m2-full-card-power-off";
+ };
+};
+
+&cp1_gpio2 {
+ status = "okay";
+};
+
+&cp1_i2c1 {
+ /*
+ * Routed to SFP.
+ * Limit to 100kHz for compatibility with SFP modules,
+ * featuring AT24C01A/02/04 at addresses 0x50/0x51.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&cp1_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&cp1_mdio {
+ pinctrl-0 = <&cp1_mdio_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ cp1_phy0: ethernet-phy at 0 {
+ reg = <0>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link is 1000Mbps: On (yellow)
+ * - LED[1]: link/activity: On/blink (green)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a17>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+
+ cp1_phy1: ethernet-phy at 1 {
+ reg = <1>;
+ /*
+ * Configure LEDs default behaviour:
+ * - LED[0]: link is 1000Mbps: On (yellow)
+ * - LED[1]: link/activity: On/blink (green)
+ * - LED[2]: high impedance (floating)
+ */
+ marvell,reg-init = <3 16 0xf000 0x0a17>;
+
+ leds {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ led at 0 {
+ reg = <0>;
+ color = <LED_COLOR_ID_YELLOW>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+
+ led at 1 {
+ reg = <1>;
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_LAN;
+ default-state = "keep";
+ };
+ };
+ };
+};
+
+/* SRDS #0 - M.2 (J30) */
+&cp1_pcie0 {
+ num-lanes = <1>;
+ phys = <&cp1_comphy0 0>;
+ status = "okay";
+};
+
+&cp1_rtc {
+ status = "disabled";
+};
+
+/* SRDS #1 - SATA on M.2 (J44) */
+&cp1_sata0 {
+ phys = <&cp1_comphy1 0>;
+ status = "okay";
+
+ /* only port 0 is available */
+ /delete-node/ sata-port at 1;
+};
+
+&cp1_syscon0 {
+ cp1_pinctrl: pinctrl {
+ compatible = "marvell,cp115-standalone-pinctrl";
+ pinctrl-0 = <&cp1_m2_1_shutdown_pins &cp1_m2_2_shutdown_pins>;
+ pinctrl-names = "default";
+
+ cp1_i2c1_pins: cp0-i2c1-pins {
+ marvell,pins = "mpp35", "mpp36";
+ marvell,function = "i2c1";
+ };
+
+ cp1_led_pins: cp1-led-pins {
+ marvell,pins = "mpp54", "mpp55";
+ marvell,function = "gpio";
+ };
+
+ cp1_m2_1_shutdown_pins: cp1-m2-1-shutdown-pins {
+ marvell,pins = "mpp29";
+ marvell,function = "gpio";
+ };
+
+ cp1_m2_2_shutdown_pins: cp1-m2-2-shutdown-pins {
+ marvell,pins = "mpp30";
+ marvell,function = "gpio";
+ };
+
+ cp1_mdio_pins: cp1-mdio-pins {
+ marvell,pins = "mpp37", "mpp38";
+ marvell,function = "ge";
+ };
+
+ cp1_rtc_pins: cp1-rtc-pins {
+ marvell,pins = "mpp12", "mpp13";
+ marvell,function = "gpio";
+ };
+
+ cp1_sfp1_pins: cp1-sfp1-pins {
+ marvell,pins = "mpp33", "mpp34", "mpp49", "mpp50";
+ marvell,function = "gpio";
+ };
+ };
+};
+
+/*
+ * SRDS #2 - USB-3.0 Host to M.2 (J44)
+ * USB-2.0 Host to M.2 (J30)
+ */
+&cp1_usb3_0 {
+ phys = <&cp1_comphy2 0>, <&cp1_utmi0>;
+ phy-names = "comphy", "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+/* USB-2.0 Host to M.2 (J44) */
+&cp1_usb3_1 {
+ phys = <&cp1_utmi1>;
+ phy-names = "utmi";
+ dr_mode = "host";
+ status = "okay";
+};
+
+&cp1_utmi {
+ status = "okay";
+};
--
2.35.3
More information about the linux-arm-kernel
mailing list