[PATCH 3/3] arm64: dts: imx8mq-evk: add typec node

[Xu Yang]

On Mon, Jul 29, 2024 at 10:56:31PM +0300, Dmitry Baryshkov wrote:
> On Mon, Jul 29, 2024 at 04:10:39PM GMT, Xu Yang wrote:
> > The first port of USB with type-C connector, which has dual data
> > role and dual power role.
> > 
> > Signed-off-by: Xu Yang <xu.yang_2 at nxp.com>
> > ---
> >  arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 93 ++++++++++++++++++++
> >  1 file changed, 93 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > index 7507548cdb16..008e8c37c76b 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
> > @@ -6,6 +6,7 @@
> >  
> >  /dts-v1/;
> >  
> > +#include <dt-bindings/usb/pd.h>
> >  #include "imx8mq.dtsi"
> >  
> >  / {
> > @@ -27,6 +28,20 @@ pcie0_refclk: pcie0-refclk {
> >  		clock-frequency = <100000000>;
> >  	};
> >  
> > +	ptn36043: typec-mux {
> > +		compatible = "nxp,ptn36043", "gpio-sbu-mux";
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_typec_mux>;
> > +		select-gpios =<&gpio3 15 GPIO_ACTIVE_LOW>;
> > +		orientation-switch;
> > +
> > +		port {
> > +			usb3_data_ss: endpoint {
> > +				remote-endpoint = <&typec_con_ss>;
> > +			};
> > +		};
> 
> If this the "SBU" mux, then why is it connected to the SS lines?
> Where are the SS lines further going?

The gpio-mux is able to switch SS line. ptn36043 is SS orientation
swich here.

> 
> > +	};
> > +
> >  	reg_pcie1: regulator-pcie {
> >  		compatible = "regulator-fixed";
> >  		pinctrl-names = "default";
> > @@ -315,6 +330,50 @@ vgen6_reg: vgen6 {
> >  			};
> >  		};
> >  	};
> > +
> > +	ptn5110: tcpc at 50 {
> > +		compatible = "nxp,ptn5110", "tcpci";
> > +		reg = <0x50>;
> > +		pinctrl-names = "default";
> > +		pinctrl-0 = <&pinctrl_typec>;
> > +		interrupt-parent = <&gpio3>;
> > +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> > +
> > +		usb_con: connector {
> > +			compatible = "usb-c-connector";
> > +			label = "USB-C";
> > +			power-role = "dual";
> > +			data-role = "dual";
> > +			try-power-role = "sink";
> > +			source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
> > +			sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
> > +				     PDO_VAR(5000, 20000, 3000)>;
> > +			op-sink-microwatt = <15000000>;
> > +			self-powered;
> > +
> > +			ports {
> > +				#address-cells = <1>;
> > +				#size-cells = <0>;
> > +
> > +				port at 0 {
> > +					reg = <0>;
> > +
> > +					typec_dr_sw: endpoint {
> 
> the DR (dual role) isn't a physical signal. These ports descrbie HS
> (high speed) lanes, please consider naming them correspondingly.

Okay.

> 
> > +						remote-endpoint = <&usb3_drd_sw>;
> > +					};
> > +				};
> > +
> > +
> > +				port at 1 {
> > +					reg = <1>;
> > +
> > +					typec_con_ss: endpoint {
> > +						remote-endpoint = <&usb3_data_ss>;
> > +					};
> > +				};
> 
> No SBU port?

Yes, this board doesn't use SBU signal.

Thanks,
Xu Yang

> 
> > +			};
> > +		};
> > +	};
> >  };
> >  
> >  &lcdif {
> > @@ -445,6 +504,28 @@ &uart1 {
> >  	status = "okay";
> >  };
> >  
> > +&usb3_phy0 {
> > +	status = "okay";
> > +};
> > +
> > +&usb_dwc3_0 {
> > +	dr_mode = "otg";
> > +	hnp-disable;
> > +	srp-disable;
> > +	adp-disable;
> > +	usb-role-switch;
> > +	role-switch-default-mode = "none";
> > +	snps,dis-u1-entry-quirk;
> > +	snps,dis-u2-entry-quirk;
> > +	status = "okay";
> > +
> > +	port {
> > +		usb3_drd_sw: endpoint {
> > +			remote-endpoint = <&typec_dr_sw>;
> > +		};
> > +	};
> > +};
> > +
> >  &usb3_phy1 {
> >  	status = "okay";
> >  };
> > @@ -597,6 +678,18 @@ MX8MQ_IOMUXC_SPDIF_RX_SPDIF1_IN		0xd6
> >  		>;
> >  	};
> >  
> > +	pinctrl_typec: typecgrp {
> > +		fsl,pins = <
> > +			MX8MQ_IOMUXC_NAND_CE2_B_GPIO3_IO3		0x17059
> > +		>;
> > +	};
> > +
> > +	pinctrl_typec_mux: typecmuxgrp {
> > +		fsl,pins = <
> > +			MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15		0x16
> > +		>;
> > +	};
> > +
> >  	pinctrl_uart1: uart1grp {
> >  		fsl,pins = <
> >  			MX8MQ_IOMUXC_UART1_RXD_UART1_DCE_RX		0x49
> > -- 
> > 2.34.1
> > 
> 
> -- 
> With best wishes
> Dmitry