[PATCH v2 1/3] dt-bindings: net: bluetooth: Add support for Amlogic Bluetooth

[Krzysztof Kozlowski]

On 18/07/2024 09:42, Yang Li via B4 Relay wrote:
> From: Yang Li <yang.li at amlogic.com>
> 
> Add binding document for Amlogic Bluetooth chipsets attached over UART.
> 
> Signed-off-by: Yang Li <yang.li at amlogic.com>
> ---
>  .../bindings/net/bluetooth/amlogic,w155s2-bt.yaml  | 66 ++++++++++++++++++++++
>  1 file changed, 66 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/net/bluetooth/amlogic,w155s2-bt.yaml b/Documentation/devicetree/bindings/net/bluetooth/amlogic,w155s2-bt.yaml
> new file mode 100644
> index 000000000000..2e433d5692ff
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/bluetooth/amlogic,w155s2-bt.yaml
> @@ -0,0 +1,66 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# Copyright (C) 2024 Amlogic, Inc. All rights reserved
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/net/bluetooth/amlogic,w155s2-bt.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Amlogic Bluetooth chips
> +
> +description:
> +  This binding describes UART-attached Amlogic bluetooth chips.

<form letter>
This is a friendly reminder during the review process.

It seems my or other reviewer's previous comments were not fully
addressed. Maybe the feedback got lost between the quotes, maybe you
just forgot to apply it. Please go back to the previous discussion and
either implement all requested changes or keep discussing them.

Thank you.
</form letter>


> +
> +maintainers:
> +  - Yang Li <yang.li at amlogic.com>
> +
> +properties:
> +  compatible:
> +    oneOf:
> +      - const: amlogic,w155s2-bt
> +      - items:
> +          - enum:
> +              - amlogic,w265s1-bt
> +              - amlogic,w265p1-bt
> +              - amlogic,w265s2-bt
> +          - const: amlogic,w155s2-bt
> +
> +  bt-enable-gpios:

enable-gpios

> +    maxItems: 1
> +    description: gpio specifier used to enable BT

Drop, redundant.

> +
> +  bt-supply:

It's called "bt" in schematics or datasheet? Feels unusual. Please list
all the pins if you claim that's a real name.



> +    description: bluetooth chip 3.3V supply regulator handle
> +
> +  clocks:
> +    maxItems: 1
> +    description: clock provided to the controller (32.768KHz)
> +
> +  antenna-number:
> +    default: 1
> +    description: device supports up to two antennas

Keep it consistent - either descriptions are the last property or
somewhere else. Usually the last.

> +    $ref: /schemas/types.yaml#/definitions/uint32

And what does it mean? What happens if BT uses antenna number 2, not 1?
What is connected to the other antenna? It really feels useless to say
which antenna is connected to hardware.

> +
> +  firmware-name:
> +    description: specify the path of firmware bin to load

Missing maxItems

> +    $ref: /schemas/types.yaml#/definitions/string-array

That's redundant, drop.

> +


Best regards,
Krzysztof