[PATCH RFC v2 4/4] arm: dts: marvell: armada-388-clearfog: add description for usb phys

[Josua Mayer]

Clearfog Base and Pro use three sets of USB-2.0 signals going to various
connectors. Only two were enabled so far without links to their phys.
Further there were some minor issues with usb port descriptions.

Firstly add references for each phy to the corresponding controller
nodes. At the same time redeclarations of controller nodes are replaced
with references to labels in armada-38x.dtsi.

Secondly enable USB-2.0 controller routed to Clearfog Base M.2 /
Clearfog Pro mPCIe connectors.

FInally add missing dr_mode properties to stop utmi phy driver from
complaining.

Signed-off-by: Josua Mayer <josua at solid-run.com>
---
 .../boot/dts/marvell/armada-388-clearfog-base.dts  |  8 ++++++
 arch/arm/boot/dts/marvell/armada-388-clearfog.dts  |  8 ++++++
 arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi | 30 ++++++++++++++--------
 3 files changed, 36 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
index f7daa3bc707e..09ba024e432e 100644
--- a/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog-base.dts
@@ -66,3 +66,11 @@ rear_button_pins: rear-button-pins {
 		marvell,function = "gpio";
 	};
 };
+
+/* SRDS #4 - USB-2.0/3.0 Host, M.2 */
+&usb3_0 {
+	phys = <&utmi1>;
+	phy-names = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/marvell/armada-388-clearfog.dts b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
index 09bf2e6d4ed0..4f5bb5867f20 100644
--- a/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dts
@@ -182,3 +182,11 @@ &spi1 {
 	 */
 	pinctrl-0 = <&spi1_pins &clearfog_spi1_cs_pins &mikro_spi_pins>;
 };
+
+/* USB-2.0 Host, CON2 - nearest CPU */
+&usb3_0 {
+	phys = <&utmi1>;
+	phy-names = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi b/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
index f8a06ae4a3c9..0497fe13f56d 100644
--- a/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
+++ b/arch/arm/boot/dts/marvell/armada-388-clearfog.dtsi
@@ -51,16 +51,6 @@ sdhci at d8000 {
 				vmmc-supply = <&reg_3p3v>;
 				wp-inverted;
 			};
-
-			usb at 58000 {
-				/* CON3, nearest  power. */
-				status = "okay";
-			};
-
-			usb3 at f8000 {
-				/* CON7 */
-				status = "okay";
-			};
 		};
 
 		pcie {
@@ -243,3 +233,23 @@ &uart1 {
 	pinctrl-names = "default";
 	status = "okay";
 };
+
+/* USB-2.0 Host, CON3 - nearest power */
+&usb0 {
+	phys = <&utmi0>;
+	phy-names = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+/* SRDS #3 - USB-2.0/3.0 Host, Type-A connector */
+&usb3_1 {
+	phys = <&utmi2>;
+	phy-names = "utmi";
+	dr_mode = "host";
+	status = "okay";
+};
+
+&utmi {
+	status = "okay";
+};

-- 
2.35.3