[PATCH 2/2] arm64: dts: rockchip: Add support for rk3588 GenBook
Dragan Simic
dsimic at manjaro.org
Tue Jul 16 06:50:47 PDT 2024
Hello Andy,
On 2024-07-16 12:07, Andy Yan wrote:
> 在 2024-07-15 22:47:04，"Dragan Simic" <dsimic at manjaro.org> 写道：
>> On 2024-07-15 12:44, Andy Yan wrote:
>>> At 2024-07-14 23:27:54, "Dragan Simic" <dsimic at manjaro.org> wrote:
>>>> Please see a few comments below.
>>>>
>>>> On 2024-07-14 13:28, Andy Yan wrote:
>>>>> Cool Pi GenBook works as a mother board connect with CM5 [0].
>>>>
>>>> s/mother board/carrier board/
>>>
>>> This can be changed to carrier board in next version。
>>>
>>>> s/CM5/GenM5/
>>>
>>> In fact, the SOM is called CM5 always[0]， even this laptop was
>>> called cm5 laptop from the
>>> very beginning of the design。
>>> They just gave it a new name GenBook when it comes to crowdsupply.
>>>
>>> The dtsi for CM5 is aready landing upstream，I inclulde it in the
>>> current genbook dts。
>>>
>>> [0]https://forum.cool-pi.com/topic/98/cool-pi-5-compute-module-minipc-carrier-board-spec
>>
>> Ah, that's quite interesting, it was probably renamed for marketing
>> purposes. Thanks for the clarification.
>>
>> To add to the confusion, none of "GenBook", "CM5" or "GenM5" appear
>> on the labels found on the actual PCBs. [1] Instead, there are only
>> some rather generic terms.
>
> So we can keep the name as it is now ？
As far as I'm concerned, yes. Everything points to "CoolPi CM5"
and "CoolPi GenBook" being the rigth names in the upstream kernel
for the SoM and the carrier board, respectively.
However, please see another comment below.
>> [1]
>> https://www.crowdsupply.com/img/6185/60c35852-7a58-4b6f-80fc-af3a0e3d6185/genbook-rk3588-main-board-close-up_jpg_gallery-lg.jpg
>>
>>>>> Specification:
>>>>> - Rockchip RK3588
>>>>> - LPDDR5X 8/32 GB
>>>>> - eMMC 64 GB
>>>>> - HDMI Type A out x 1
>>>>> - USB 3.0 Host x 1
>>>>> - USB-C 3.0 with DisplayPort AltMode
>>>>> - PCIE M.2 E Key for RTL8852BE Wireless connection
>>>>> - PCIE M.2 M Key for NVME connection
>>>>> - eDP panel with 1920x1080
>>>>>
>>>>> This patch add basic support to bringup eMMC/USB HOST/WiFi
>>>>> and can also drive a HDMI output with out of tree hdmi patches.
>>>>>
>>>>> [0]
>>>>> https://www.crowdsupply.com/shenzhen-tianmao-technology-co-ltd/genbook-rk3588
>>>>>
>>>>> Signed-off-by: Andy Yan <andyshrk at 163.com>
>>>>> ---
>>>>>
>>>>> arch/arm64/boot/dts/rockchip/Makefile | 1 +
>>>>> .../dts/rockchip/rk3588-coolpi-genbook.dts | 296
>>>>> ++++++++++++++++++
>>>>> 2 files changed, 297 insertions(+)
>>>>> create mode 100644
>>>>> arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>
>>>> It would be better to split this into two files: a dtsi for the
>>>> GenM5
>>>> system
>>>> on module, and a dts for the GenBook carrier board. That way, the
>>>> dts(i) files
>>>> would describe the actual hardware better.
>>>>
>>>>> diff --git a/arch/arm64/boot/dts/rockchip/Makefile
>>>>> b/arch/arm64/boot/dts/rockchip/Makefile
>>>>> index 8fa469db400c..0fad54939bbd 100644
>>>>> --- a/arch/arm64/boot/dts/rockchip/Makefile
>>>>> +++ b/arch/arm64/boot/dts/rockchip/Makefile
>>>>> @@ -122,6 +122,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) +=
>>>>> rk3568-wolfvision-pf5-display-vz.dtbo
>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) +=
>>>>> rk3568-wolfvision-pf5-io-expander.dtbo
>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-sige7.dtb
>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-cm5-evb.dtb
>>>>> +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-coolpi-genbook.dtb
>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-io.dtb
>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6a-wifi.dtbo
>>>>> dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-edgeble-neu6b-io.dtb
>>>>> diff --git a/arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>> b/arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>> new file mode 100644
>>>>> index 000000000000..28357c6f05fb
>>>>> --- /dev/null
>>>>> +++ b/arch/arm64/boot/dts/rockchip/rk3588-coolpi-genbook.dts
>>>>> @@ -0,0 +1,296 @@
>>>>> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
>>>>> +/*
>>>>> + * Copyright (c) 2024 Rockchip Electronics Co., Ltd.
>>>>> + *
>>>>> + */
>>>>> +
>>>>> +/dts-v1/;
>>>>> +
>>>>> +#include <dt-bindings/leds/common.h>
>>>>> +#include "rk3588-coolpi-cm5.dtsi"
>>>>> +
>>>>> +/ {
>>>>> + model = "RK3588 CoolPi GenBook";
It would be better to omit "RK3588" from the model name and use
"CM5" instead, because that more precisely reflects the "dependency
graph", so to speak. Thus, I'd suggest that "CoolPi CM5 GenBook"
is used as the model name.
Technically, "CoolPi CM5 on GenBook carrier board" would be a more
correct model name, so that's another option, but the above-proposed
"CoolPi CM5 GenBook" sounds more like a finished product/device
than just some carrier board with an SoM.
>>>>> + compatible = "coolpi,genbook", "coolpi,pi-cm5",
>>>>> "rockchip,rk3588";
>>>>> +
>>>>> + backlight: backlight {
>>>>> + compatible = "pwm-backlight";
>>>>> + enable-gpios = <&gpio4 RK_PA3 GPIO_ACTIVE_HIGH>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&bl_en>;
>>>>> + power-supply = <&vcc12v_dcin>;
>>>>> + pwms = <&pwm6 0 25000 0>;
>>>>> + };
>>>>> +
>>>>> + leds: leds {
>>>>> + compatible = "gpio-leds";
>>>>> +
>>>>> + heartbeat_led: led-0 {
>>>>> + color = <LED_COLOR_ID_GREEN>;
>>>>> + function = LED_FUNCTION_STATUS;
>>>>> + gpios = <&gpio1 RK_PB0 GPIO_ACTIVE_HIGH>;
>>>>> + linux,default-trigger = "heartbeat";
>>>>> + };
>>>>> +
>>>>> + wlan_led: led-1 {
>>>>> + color = <LED_COLOR_ID_GREEN>;
>>>>> + function = LED_FUNCTION_WLAN;
>>>>> + gpios = <&gpio0 RK_PC5 GPIO_ACTIVE_HIGH>;
>>>>> + };
>>>>> +
>>>>> + charging_red: led-2 {
>>>>> + function = LED_FUNCTION_CHARGING;
>>>>> + color = <LED_COLOR_ID_RED>;
>>>>> + gpios = <&gpio3 RK_PD2 GPIO_ACTIVE_HIGH>;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + vcc12v_dcin: vcc12v-dcin-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc12v_dcin";
>>>>> + regulator-always-on;
>>>>> + regulator-boot-on;
>>>>> + regulator-min-microvolt = <12000000>;
>>>>> + regulator-max-microvolt = <12000000>;
>>>>> + };
>>>>> +
>>>>> + vcc_sys: vcc-sys-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc_sys";
>>>>> + regulator-always-on;
>>>>> + regulator-boot-on;
>>>>> + regulator-min-microvolt = <7000000>;
>>>>> + regulator-max-microvolt = <7000000>;
>>>>> + vin-supply = <&vcc12v_dcin>;
>>>>> + };
>>>>> +
>>>>> + vcc5v0_sys: vcc5v0-sys-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc5v0_sys";
>>>>> + regulator-always-on;
>>>>> + regulator-boot-on;
>>>>> + regulator-min-microvolt = <7000000>;
>>>>> + regulator-max-microvolt = <7000000>;
>>>>> + vin-supply = <&vcc_sys>;
>>>>> + };
>>>>> +
>>>>> + vcc3v3_sys: vcc3v3-sys-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc3v3_sys";
>>>>> + regulator-always-on;
>>>>> + regulator-boot-on;
>>>>> + regulator-min-microvolt = <3300000>;
>>>>> + regulator-max-microvolt = <3300000>;
>>>>> + vin-supply = <&vcc5v0_sys>;
>>>>> + };
>>>>> +
>>>>> + vcc3v3_lcd: vcc3v3-lcd-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc3v3_lcd";
>>>>> + enable-active-high;
>>>>> + gpio = <&gpio1 RK_PC4 GPIO_ACTIVE_HIGH>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&lcdpwr_en>;
>>>>> + vin-supply = <&vcc3v3_sys>;
>>>>> + };
>>>>> +
>>>>> + vcc5v0_usb: vcc5v0-usb-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc5v0_usb";
>>>>> + regulator-boot-on;
>>>>> + regulator-always-on;
>>>>> + enable-active-high;
>>>>> + regulator-min-microvolt = <5000000>;
>>>>> + regulator-max-microvolt = <5000000>;
>>>>> + gpio = <&gpio1 RK_PD5 GPIO_ACTIVE_HIGH>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&usb_pwren>;
>>>>> + vin-supply = <&vcc_sys>;
>>>>> + };
>>>>> +
>>>>> + vcc5v0_usb_host0: vcc5v0_usb30_host: vcc5v0-usb-host-regulator {
>>>>> + compatible = "regulator-fixed";
>>>>> + regulator-name = "vcc5v0_host";
>>>>> + regulator-boot-on;
>>>>> + regulator-always-on;
>>>>> + enable-active-high;
>>>>> + regulator-min-microvolt = <5000000>;
>>>>> + regulator-max-microvolt = <5000000>;
>>>>> + gpio = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&usb_host_pwren>;
>>>>> + vin-supply = <&vcc5v0_usb>;
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&gmac0 {
>>>>> + status = "disabled";
>>>>> +};
>>>>> +
>>>>> +/* M.2 E-Key */
>>>>> +&pcie2x1l0 {
>>>>> + reset-gpios = <&gpio4 RK_PA2 GPIO_ACTIVE_HIGH>;
>>>>> + vpcie3v3-supply = <&vcc3v3_sys>;
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&pcie_clkreq &pcie_wake &pcie_rst &wifi_pwron
>>>>> &bt_pwron>;
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&pcie2x1l2 {
>>>>> + status = "disabled";
>>>>> +};
>>>>> +
>>>>> +&pcie30phy {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +/* M.2 M-Key ssd */
>>>>> +&pcie3x4 {
>>>>> + reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
>>>>> + vpcie3v3-supply = <&vcc3v3_sys>;
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&pinctrl {
>>>>> + lcd {
>>>>> + lcdpwr_en: lcdpwr-en {
>>>>> + rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>;
>>>>> + };
>>>>> +
>>>>> + bl_en: bl-en {
>>>>> + rockchip,pins = <4 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + usb {
>>>>> + usb_pwren: usb-pwren {
>>>>> + rockchip,pins = <1 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> +
>>>>> + usb_otg_pwren: usb-otg-pwren {
>>>>> + rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> +
>>>>> + usb_host_pwren: usb-host-pwren {
>>>>> + rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> + };
>>>>> +
>>>>> + wifi {
>>>>> + bt_pwron: bt-pwron {
>>>>> + rockchip,pins = <3 RK_PA6 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> +
>>>>> + pcie_clkreq: pcie-clkreq {
>>>>> + rockchip,pins = <4 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> +
>>>>> + pcie_rst: pcie-rst {
>>>>> + rockchip,pins = <4 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> +
>>>>> + wifi_pwron: wifi-pwron {
>>>>> + rockchip,pins = <3 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> +
>>>>> + pcie_wake: pcie-wake {
>>>>> + rockchip,pins = <4 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
>>>>> + };
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&pwm6 {
>>>>> + pinctrl-0 = <&pwm6m1_pins>;
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&sdmmc {
>>>>> + status = "disabled";
>>>>> +};
>>>>> +
>>>>> +&sfc {
>>>>> + pinctrl-names = "default";
>>>>> + pinctrl-0 = <&fspim2_pins>;
>>>>> + status = "okay";
>>>>> +
>>>>> + flash at 0 {
>>>>> + compatible = "jedec,spi-nor";
>>>>> + reg = <0x0>;
>>>>> + spi-max-frequency = <100000000>;
>>>>> + spi-rx-bus-width = <4>;
>>>>> + spi-tx-bus-width = <1>;
>>>>> + };
>>>>> +};
>>>>> +
>>>>> +&u2phy0 {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy0_otg {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&usbdp_phy0 {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy1 {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy1_otg {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy2 {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy3 {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy2_host {
>>>>> + phy-supply = <&vcc5v0_usb_host0>;
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&u2phy3_host {
>>>>> + phy-supply = <&vcc5v0_usb>;
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&usbdp_phy1 {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +/* For Keypad */
>>>>> +&usb_host0_ehci {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&usb_host0_ohci {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +/* Type C port */
>>>>> +&usb_host0_xhci {
>>>>> + dr_mode = "peripheral";
>>>>> + maximum-speed = "high-speed";
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +/* connected to a HUB for camera and BT */
>>>>> +&usb_host1_ehci {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +&usb_host1_ohci {
>>>>> + status = "okay";
>>>>> +};
>>>>> +
>>>>> +/* USB A out */
>>>>> +&usb_host1_xhci {
>>>>> + dr_mode = "host";
>>>>> + status = "okay";
>>>>> +};
More information about the linux-arm-kernel
mailing list